Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 28/02/19 in all areas

  1. Wolfgeorge

    Gun picture thread

    Brass Chromeplated Prime Colt 1911 Commemorative WWII European theater Wolf
    3 points
  2. 2 points
  3. G&G L22A2. Shmexy little low profile RDS and an FMA PEQ10. The Rail Riser arrived this morning and now the RDS is at the perfect height and although I'm still waiting on the foregrip to arrive, it's done. The more I look at the rifle, the more the upper receiver is begging for attention. I just can't decide whether to go OD, a darker shade of tan or take it back to black and slap some decals on it. Opinions? 😁
    2 points
  4. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 Statement Defense elite glock 004 WE base Custom order cerakote toy & real toy & real toy & real
    2 points
  5. Got one of these from LWA today - cheers chaps for not selling it or sending me a stock one instead..... G&G say 29rps and it will perform with a 7.4v like a 11.1v lipo Well that 29rps must be with a 11.1v I reckon coz been doing a quick chrono and it hits about 21-22 with a fresh 7.4v lipo OK quick review - mods feel free to move this but posted here as it is "news" but deffo not good news imho Gets her out of box, small tamiya on there - hmmm ok was expecting maybe deans or mini-deans Also Standard G&G sticker on gearbox - not perhaps a Top Tech sticker ??? Hmmm was expect a TT sticker as it is supposed to have a DSG & ceramic bearings in there, plus probably a m160+ spring to compensate for the half stroke from the DSG...... Connects a fresh 7.4v lipo switches to semi - goes full auto - WTF ????? messes about with selector - but can't get her to fire semi at all - great got a friggin lemon selector switch Then checks the instructions afterwards in typical bloke style..... NO SEMI AUTO MODE ON HC05 !!!! Oh that is just dandy - design a CQB gun that don't do semi when often up close you have to switch to semi only !!! Also was expecting better than stock wiring and perhaps a mosfet in there didn't appear to have fet in there but didn't look ultra hard coz just wanted to see how quick she fires then...... WTF on the chrono with a decent mag - 21rps, try again hhhmmmm 20.5rps - that is crap OK dry fire test against the AK12 I did - yup sounds similar but even with a used 7.4v I'd give the AK12 the edge That beefy motor AK12 hits 24.8rps on fresh 7.4v Which means my M4 mag ain't misfeeding to give low results - she is hitting about 20 to 21 max on a 7.4v Soz but that is crap to me and not what I was expecting or lead to believe from the hype................. OK very very fresh 11.1v lipo kicking out about 12.3v test: 33 to 35rps and about 290 to 300fps - did about 4 or 5 bursts on 11.1v but as I think it ain't got a fet in there ain't gonna go real nutz coz the poor trigger may decide to have a bigger meltdown than some teenage drama queen not getting their own way........ So at £155 or £180 rrp from LWA - they only had 3 and they are all gone yesterday afternoon Is it worth it ??????????? out of the box - NO - mainly coz no semi but also not that great rof for a DSG imho With tweaks - I think uhmm well uhmm not sure now I've ripped her wide open and seen not able to get cut off/semi working it must be pulling some beefy motor if it is a DSG and beefy spring, plus does have ceramic bearings in there they ain't cheap either..... Will need a rewire and fet but then she should safely be able to use it at 40+ on 11.1v or 26 on 7.4v Still can't see it hitting 29rps on 7.4v even with 16awg deans etc...... well "maybe" if the wires are soldered to motor and high performance/fresh of charge mofo 7.4v battery but that is after a rewire and deans and is really really doing all you can for max contact and zero resistance Also worth noting that G&G could have totally ripped off Seigtek DSG - RiotSC was not approached by G&G and it seems to be a clone of his gears he said Note the 3 holes on each side of gear - not SHS type or Modify's either if you look at the launch poster of the HC05 it shows a DSG exactly like the above pic So not impressed that G&G "could" have ripped off Seigtek DSG - RiotSC's design Even less impressed that a DSG performs - well not that great and not much better than a tweaked SSG AK12 is still on 18:1 but mega beefy motor - but no not that stupid to put 11.1v and get Pre Engagement But a fairly decent 12:1 shortstroke SSG would wipe the floor with the HC05 out of the box (must be like a 18:1 DSG gearing me thinks not any higher speed DSG) So yeah not quite as good performing as we are lead to think and NO SEMI - jeez that is dumb ahhh well a couple of pics: soz if they are a bit big, can't be ar$ed (like G&G's tech dept can't be ar$ed to do it properly) and the instructions when you find you not got semi ffs
    1 point
  6. Wo1f

    THE TM MWS thread

    The mws is about the only gbbr I haven’t had a bolt lock issue with. If you’ve tried unscrewing the buffer to no avail, I’d consider removing and cleaning the ZET plate and the areas it makes contact with. It sounds like it’s not rising quick enough to catch the bolt when it’s rearward. If you have a heavier recoil buffer or spring, try that and see if it makes a difference. Should give you an indication that the ZET plate isn’t moving quick enough.
    1 point
  7. THIS ADVERT IS 'UNCOMPLETED' - THIS MEANS THE ADVERTISER HASN'T BUMPED THIS LISTING, BUT IT COULD STILL BE WORTH CONTACTING THEM.

    • For sale
    • Used

    Hi guys here is my G&P M4 Airsoft rifle navy seal edition. High quality as you would expect from a G&P rifle, it shoots at 330 fps no issues whatsoever it shoots perfectly. It comes with two mags a hi cap and a low cap, it also comes with the correct G&P 2300 8.4 nunchuck battery for the crane stock. Its a bargain at £145.00 collected from Birmingham or £160.00 posted via parcel force 48hr tracked & signed for. Feel free to contact me directly on 07746673219

    £145

    1 point
  8. L3wisD

    Gun picture thread

    Haven't wandered into this thread in some time.... All I have to say is: @heroshark I need that USP Compact... my word I've come over in a hot flush.
    1 point
  9. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 COLT M727 GHK base
    1 point
  10. Pratting about in the house.
    1 point
  11. 1 point
  12. Few pictures of my work in progress MTP kit from a 'Mini-game' I did with a few mates a couple of weeks ago... Photos by our good friend 'PJ'. -Does this thing have anything in it? - I've since got a new lower mesh to go over the snood; one of the newer half soft ones. My old one was just a bit uncomfortable, especially over the snood. Although both are rather warm. Rainbow 6 Siege style victory pose! A couple more people I've convinced into the glorious money pit that is Airsoft! 😂 (One of them was too stubborn) -And thanks to my Brother and my Dad for lending us their guns for the day so we'd all be armed. Wouldn't have been much fun otherwise. It's far more interesting when your targets shoot back.
    1 point
  13. Few pictures from my last game.
    1 point
  14. As first post on this forum : One of my Teammate (left) and I (right).
    1 point
  15. Havent had chance to tune and shoot it yet but first impressions: I have never handled an airsoft weapon of this quality. When they call it a "training weapon" they werent kidding. I am very impressed at how compatible the parts are for these things. Ive chucked a bunch of aftermarket parts on as you can see, which confirmed for me almost everything is compatible with Milspec, AEG, and GBBR parts which is handy for anyone moving over to HPA that previously owned an M4/AR based gun. I am very glad wolverine made their rail system M-LOK over keymod. looks a feels 100 times nicer. I was lost for words at how light this thing was despite it being 90% full metal. I could give this to a young teenager and they would be able to sport this all day without a problem. Definitely lighter than my G&G Scar-L. Aesthetically and Ergonomically I cant find a single fault with the base gun bar two things. The only issues I faced was the split receiver (these things break down exactly like real AR's) was abit wobbly. Fortunately I had a spare G&P magic pin which resolved this issue right away. I havent seen many people speak about this issue on the forum so i could have been unlucky. But either way, if you find the same issues, its less than a tenner to amend. Secondly, my after market stock (AEG) was very wobbly when fitting. This was to be expected as ive heard many people mention this on the Wolverine Owners group on facebook. Easiest solution in the world: couple strips of electrical tape either side & the top of the buffer tube (where it would be hidden under the stock), slid the stock back ona nd no wobble at all. You'd never know the tape was there by sight also. My only suggestion to wolverine would be to have some kind of sling mount added to the stock gun or at least have it as a option in their "gun builder" on their site or high pressure airsoft's site. I had to find a mil spec AR sling mount end plate on ebay so i can use my single point sling.
    1 point
  16. Well I only got off about 100 shots before the gears broke but here's the latest addition to my collection: LCT AKM
    1 point
  17. This is entirely @rocketdogbert's fault. And it's lovely...
    1 point
  18. so I've finally bought my first GBBR and joined the TM can club all in one shot... it's a TM mws CQBR 😎 it also turns out that recoil on a rifle is quite entertaining, who knew 😁
    1 point
  19. heroshark

    Gun picture thread

    My hk pistols. Not all my hk pistols but these look nice as a group.
    1 point
  20. New gun box ‘Flambeau tactical AR gun case’ , not quite a Peli case but then again I’ve never actually ‘needed’ a gun case that will survive being dropped from 10miles up airsofting ? 😉
    1 point
  21. heroshark

    Gun picture thread

    I have a dust pan brush . I spray paint on to my workshop door work it on to the brush then on to the slide. I use various colours and when I worked it into the brush on the door picks up a little of what was already there. After that I take some tan colour water based model paint and dab it all over and just work it in with my hands for the grubby look.
    1 point
  22. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 INGLIS Browning hi power Chinese contract WE base SN:CH20 Custom order WE hi power base deep marking, deep 0.3mm custom Lanyard loop toy & real toy & real
    1 point
  23. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 FN M1935 Chinese contract SN:8503 WE base Custom order deep marking, deep 0.3mm real gun wood grip toy & real toy & real toy & real toy & real
    1 point
  24. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 COLT M1911 Early sn33 KJ base deep marking, deep 0.3mm real 1911 wood grip chamber unlock spring toy & real toy & real toy & real toy & real
    1 point
  25. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 HK G3 DMR VFC base Custom order cerakote finish finish
    1 point
  26. july_pi

    custom gbb

    【CUSTOM GBB WORKSHOP】 BERETTA M9A3 ksc base Tritium night sight grip fix cerakote
    1 point
  27. Well the gearbox is a bit crap tbh... They fitted 9mm ceramic bearings but not all the same ones... Sector & Spur/middle gear have 9mm outer & 5mm inner race ceramics Bevel gear though 9mm outer & 3mm inner race So in effect the sector/spur gears have thicker but not so common 5mm shafts Bevel - average bevel gear I suppose 3mm shaft Gear Ratio is 18:1 no mega spring spacers but jeez that spring (was at rest btw coz released AR latch) is a mofo Also all steel teeth & strengthen piston - std G&G piston head & plastic white cylinder head used in normal CM's seals not bad but is new with say 250 300 rounds through it - could/should be a tad better But AOE wasn't done either - just like CM's - yup 2nd tooth removed but that was it, maybe usual 2-4mm sorbo needed Nozzle - looked bog standard CM non o-ring nozzle - deffo could be a lot better Ah yes no cut off lever - ok should be able to put in one... NOPE - dual sector does NOT have any cam lift point(s) on there at all Great - coz they are 5mm shafts and 9mm outer rim bearings can't fit a SHS Dual Sector either (well I could I guess if I had say normal 9mm/3mm bearings but only got up to 8mm) On top of that the finish sector shimmed tight - ok got that a bit better but it snags at same point (deffo sector - well 99% it is sector with bad finish - very crap) but even after picking through all teeth on both sector/spur and smoothing over the back of sector coz it was that roughly cut finished still seems to snag/bind a little it seems - jeez this was really just chucked together Still haven't fully got it turning 101% smooth as I want to see it Cylinder - seemed to have grabbed a normal CM ported cylinder - ooh that ain't quite right and then took a Black n Decker to it to drill a 5mm hole as well (G&G's diy modding of drilling the hole not mine btw) Piston Spring Guide with bearing - this seemed to loose at the end and not fully tight or screwed together All in all a very pi$$ poor box - way below what I was hoping, the No semi you are kind of stuck with possible options could be a Seigtek DSG or perhaps say a Kong II burst wizard thingy fet but not ideal to get a quick change from full to semi plus all this extra cost and hassle when G&G should of done their homework better in the first place Seriously chaps - you ain't missing much at atm - this is not a great gun from G&G like we was told/hoping for atm they need to revise a lot of these issues - better quality gear/finishing & give us the semi as well ffs GEARBOX WITH DIFFERENT SIZE BEARINGS.... CRAP AOE & DIY PORTING OF CYLINDER DSG STILL SNAGGING ON SPUR, SOMETHING IS STILL SHARP AND CRAP PLUS THE SPRING BEARING GUIDE THAT ISN'T FULLY SECURED TOGETHER Not one of their best bits of AEG building and really should charged a bit more to put it together properly WITH SEMI AUTO !!!! use SHS DSG ffs if you don't want to use Seigtek's - but c'mon this is really a bit of a let down I feel (warranty void but wtf at least I know exactly why no semi & some other stuff) There is something deffo wrong with them gears and snagging/binding on sector/spur holding box together with just those 2 gears in there you get to a point and they snag keep going at this snag point and the very top of box starts to open/seperate then closes back after snag point the gears finish is like some really blunt cutting tool or more like roughly punched/cut out - hence me trying to file and try to reduce the rough snagging finish. It is either a bad - no very f*cking bad finish like I think or the shafts/gears are bent perhaps - jeez this is crap Never experienced stuff this bad before even on a crappy cheapo set of gears and the ceramics are quite deep needing very very few special shims on there so can't just keep adding shims (well they are bigger shims 5mm hole that I don't have and M5 washers are way way too fat) The ceramic bearings - well they ain't like them super duper Modify ones that seem to spin forever Actually had ordinary 8mm bearings spin better/longer but the ceramics are supposed to be much stronger. (well like I said not impressed with a not so long spin test on them) tired and fed up - will have a rethink - might contact G&G or just grab a normal box, radius it up fit SHS DSG + 16:1 bevel/spur not gonna be so great but shouldn't snag or bind and at least I might have a semi auto on that build..... Or other option I'm seriously considering is very hi-speed gears, short stroke, m125 spring, mega beefy motor and see if I can get a good deal over 30rps on 7.4v - sod G&G's lemony DSG build Unsure SHS Short Stroke SSG ultra hi-speed or SHS DSG option and have a semi at last - really don't know atm Have ordered up some 9mm bearings with 3mm centre's for now - yeah I know should be using bushings But couldn't easily find good 9mm bushings locally to arrive asap so I can put this pile of crap back together with other gears (got the bevel 9mm ceramic with 3mm centre to use or move to sector gear I guess or leave on bevel as it turns the most) Like to think I got a lemon - but if you was thinking about the HC05 - yeah just keep thinking for now, don't rush out to buy one I'm done for now S D
    1 point
×
×
  • Create New...