Leaderboard
Popular Content
Showing content with the highest reputation on 19/09/21 in all areas
-
Not a single one of my RIF's has a mosfet ( more bloody electronics to go wrong , I hate tech ! ) and they all run 7.4 Lipo's . Biggest thing to be aware of is not over discharging the battery. If I use the same gun all day I change the battery at lunch time.4 points
-
airsoft things you don't understand
Druid799 and 3 others reacted to Cannonfodder for a topic
People who turn up to a site week in week only to spend every minute whinning and bitching. If the site is that bad then why come in the first place?4 points -
airsoft things you don't understand
Druid799 and 2 others reacted to SgtTalbert for a topic
3 points -
Most of, if not all ?, of my guns are older generation kit, before mosfets became a "thing", & I run them all on 7.4 lipo's without any issues, did have an 11.1 but stopped using it as it spun everything waay to quickly for my liking.3 points
-
One of the things I found during my first few games is that I was finishing the day with a headache, although I was packing litres of water away during the day and having lunch. Unfortunately water doesn't replace the electrolytes you use during the game and lose through sweating. I take a 4 pack of lucozade sport now, as they were my go to drink when I used to play football, finish the day headache free now!2 points
-
I've got one of those too, must get round to actually using it ! Lol2 points
-
TM MP5 NGRS Owners
Ghost_86 and one other reacted to mightyjebus for a topic
G&P RIS Rail and G&P scope mount fit fine. A saddle bag 7.4v Lipo can be fitted in the front RIS however I might need to shorten the wires slightly for it to look a bit better. *edit - A suystema TW5 full stock will fit with a bit of dremeling or sanding.2 points -
@Vialli, definitely get 7.4v Li-Po's [1300mAh or higher that will fit] ...and a good charger. (SkyRC S60) Of my 16 AEGs, only one has a MOSFET. All use 7.4v except the Lonex BAW which uses 11.1v because of the recoil system but it doesn't have a MOSFET. The main downside of not using a MOSFET is arching on the trigger contacts will eventually damage the surfaces possibly to the point of not making good contact anymore but that would take a VERY long time. Using 11.1v will obviously accelerate the process so I'll have to keep an eye on that but even so it will take a long time to have a noticeable effect. Pulling the trigger slowly is worse for this situation.2 points
-
airsoft things you don't understand
Chicken pie and one other reacted to Shamal for a topic
Yeah but I really can't understand that. What's not to like? For myself I pay my money,get dressed up go along have a great time,chat,drink some coffee and maybe get a few hits during the day which is a bonus. I'm under no illusions as to my abilities. I may as well have a flashing beacon on my head because my prowess at concealment is sadly lacking. I can't lay down( I would probably have a sleep if I did),kneeling is a pain and there are very few trees wide enough or my shape as to provide cover lol. But I'm not there to win prizes for fashion or form. It's because I like it. 👍 Regards2 points -
Fuck that indeed, no amount of excuses from his end would convince me he can be trusted 👿2 points
-
it wasnt a rif, it was a firearm (airgun). Important difference2 points
-
Using lipos without a mosfet.
JamesAirsofterAgent and one other reacted to Leonine for a topic
I guess 7.4v LiPos won’t hurt right? 🤔 As long as you use them correctly I guess they should be ok. Correct me if wrong though.2 points -
Macks airsoft dreamers of the week thread
Rogerborg and one other reacted to Cannonfodder for a topic
Also wants payment via PayPal friends and family or bank transfer. Fuck that2 points -
Another RIF incident in the news... Its only a matter of time now
Rogerborg and one other reacted to Cannonfodder for a topic
Wow, some of the ideas put up here would kill off airsoft just as quickly as any government legislation Tbh I kind of agree. Waving a rif around in public and/or pointing it at a police officer should automatically put you up for a Darwin award2 points -
The new TM NGRS mp5. Had my first game last Sunday with it and as with all TM guns it obviously shoots amazing out the box but with the new MOSFET system, just a huge improvement on trigger response and no lock ups on semi which essentially saves the need for a titan. Trigger pull is short which is nice with good spring tension and the fire selector has a firm click and no play between each setting which is unlike any other AEG mp5 unless your lucky enough to have a TW5. Converted to a SD straight out the box as that's my preferred mp5 variant. I jubilee clip a lower kac rail with a stubby tango grip and looking at sourcing a eotech for the devgru look. As my user name suggests I love mp5s grew up seeing them in films and TV shows, I normally run a MWS as performance wise it's hard to beat but the build quality and performance of the mp5 is outstanding so I bumped the FPS up out the box so its now up there with the MWS and I personally feel like the MWS will start gathering dust now ha.2 points
-
Yes did build up a SD6. Finished it last night came out lovely. Wasn't too hard to build if you can get original ICS parts and have access to a lathe to build an adapter. Longer barrel and new spring bumped my FPS up too 340 so looking forward to using it tomorrow for its first outing. Also fitted my magpul guard and gemtech QD suppressor from my other ngrs mp5 I built myself to see what fitted and they went straight on. I have a real steel sliding stock that I wanna try out but I think only the rails of the stock will fit with some milling so I might stick with the original as it's way more solid than any sliding stock on Rif.2 points
-
Hi all I recently played a game at a different site from my normal one. all my guns were firing way under the FPS. but now I’ve been told that they were all too hot due to the joules. At that site the max J for a rif that has full auto is 1.14J ( uk law is 1.3) The site told me this is due to their insurance. but in the five years I’ve been playing Airsoft I never have been to a site that request you to measure in Joules. The law came out in 2017 and has taken them till 2021 to enforce it on this site. so my question is how does everyone feel about this and is everyone finding this problem across the UK? https://assets.publishing.service.gov.uk/government/uploads/system/uploads/attachment_data/file/610380/2017_04_19_-_PCA2017_firearms_provisions_-_HO_Circular_-_final.pdf1 point
-
Once accidentally left an alarm still attached to a battery after taking it out of the gatt , went to charge it the following Saturday ready for the next days gameday and discovered it was dead as a dodo AND ballooned up like a Bratwurst ! 🤦♂️1 point
-
Sure you can mention me, buddy. I'm 6ft 2, average build floating towards the dad bod, and I don't know if it's cuz I've hit mid 30s but I've noticed I've started to sweat more than a glassblowers arse while doing exercise! I've kept off the sugar loaded fizzy drinks, hence why the coke zero I took the following month did naff all! Would recommend the raspberry lucozade sport over the orange tho 😂👍1 point
-
What annoys me? People that get upset that other people aren't having fun properly.1 point
-
Fun fact (not really but you’ll get it 😉) if using a lipo alarm always remove it at the end of the day because if you don’t within a couple of days it will have killed your battery ! 😱it draws a minute amount of power so if your Batt is depleted from use it’s just enough to end your battery . Rather ironic really that the alarm that’s supposed to protect your batteries will kill them if left unsupervised ! 🤦♂️1 point
-
Thanks for all the advice,7.4 lipo it is then.one to fit in the full stock of my mp5 and a crane stock version to fit the handguard in an ics m4 and that sky rc s60 charger.1 point
-
Another RIF incident in the news... Its only a matter of time now
Tactical Pith Helmet reacted to Spartan09 for a topic
Well.... IIRC, they did also try an escape attempt at colditz by carving a pistol out of bars of soap and painting it with paint stolen from the theatre... And then dressing in stolen german uniforms and trying to walk out of the front gate...1 point -
It is not difficult to do, just take your time.1 point
-
airsoft things you don't understand
JamesAirsofterAgent reacted to Hobbnob for a topic
"Good luck passing chrono with 5.56 mate" XD1 point -
You can replace the trigger contacts multiple times for the price of the cheapest mosfet. It's not something to worry about.1 point
-
Does anyone know of some decent airsoft channels where the people videoing dont have
GAMBLE reacted to JamesAirsofterAgent for a status update
Does anyone know of some decent airsoft channels where the people videoing dont have insane RIFs, just your average joe equipment/rifs?1 point -
The 300 bar dive tank is the correct tank to fill your "gun tank" with. I've currently got a 3litre one but will be upgrading to a 7litre tomorrow as too many of my mates run HPA now and I run 3, but could use upto 5 of mine with HPA now.1 point
-
On that point, I have a lipo "alarm", essentially a little chip with a buzzer on it that will sound if the battery gets to the point it needs changing, hopefully before it does itself any harm, & itplug in to the batteries charging lead so easy to switch between gats1 point
-
airsoft things you don't understand
shadowfacex reacted to alxndrhll for a topic
The folks that dip out before a day is over (or the 'Photo Ops' as I call them). Show up, get their photos to show they were there, contribute very little to game(s) and then disppear early citing a whole number of reasons ranging from injuries to 'the entire other team are cheating'. Just never understood it, and if I was to be leaving early I'd absolutely be getting a refund before I did. I'm aware there are absolutely cases where there is an entirely valid reason, and I'm not talking about those. But especially since all the pandemic restrictions lifted I feel like there are half the people remaining at the end of the day than what there were at the start, seemingly irrelevant of the site. It's been touched on by a few folks, but this is one of the only... perhaps the only hobby I've had where people seem to have it as a hobby, but not actually like playing the game 🤷♂️.1 point -
Might be the nub itself has slipped? I've made the same changes to my apache but have used an omega nub. It barely needs the hop on, so might be worth looking at? Can you see it pressing on the hop rubber before you re- assemble it?1 point
-
Working out the best BB weight
AirSniper reacted to Adolf Hamster for a topic
assuming your son's is the left-hand one then looks like it's not too bad with only one shot being significantly low. the range of readings if you discount that flier is really not too bad and the lower average more likely just means the spring being a tad softer. chrono data like that is about as good a diagnosis of air seal as you can get without stripping the box or having some range time to check vertical dispersion.1 point -
airsoft things you don't understand
shadowfacex reacted to Wavey_Gravey for a topic
Why people are happy to pay £30+ not including fuel, bb’s, gas and everything in between to spend the day…for lack of a better phrase, floating. You get out what you put in and I find a lot of people moaning they had a crap / slow day are the ones that float and never get stuck in.1 point -
General aeg range
Pewpewpetie reacted to Rogerborg for a topic
/thread You can get hits at longer range, on targets who helpfully stand still while you figure out where your BBs are hooking, slicing, lobbing or dropping at this exact point in time. Anyone who tells you that their gnu shoots like a laser out to 70m is delusional, or trying to sell it to you.1 point -
If a criminal wants a fake gun that looks real enough to commit a crime with then they don't need anything that looks even close to what we use. They could easily make something that looks realistic enough (or even easier than that they could simply buy an airgun that's just as realistic-looking as any of our RIFs), so imposing any further restrictions would be utterly pointless.1 point
-
airsoft things you don't understand
JamesAirsofterAgent reacted to shadowfacex for a topic
@Adolf Hamster has already mentioned late starts and overly long briefs. If you need a special brief for newbs/rental, do it separately, tell them to come earlier, I don’t care, but don’t take 1hr for a brief just because you need to explain fundamental principles of shooting BBs to 5 people when the party is 120 strong. I don’t get power players, hyped up on adrenaline, who consistently do not take their shots and jump left and right dodging BBs when they get visibly and audibly hit then banged with a frag (or a few). Goddamn John Wick wannabes. What’s the point? You wanna piss off a few other guys so they spray you till you take your hits? Bad outcome for everyone.1 point -
Another RIF incident in the news... Its only a matter of time now
John_W reacted to Oneshotscott for a topic
Like.. Ermmm.. TWO TONE..... yikes1 point -
1 point
-
airsoft things you don't understand
Akuma121 reacted to Jaylordofwaargh for a topic
Patches.....i can understand event patches its the patch walls i cannot understand. Full disclosure, I do have a handfull of patches - a couple of deadpool crossovers a fb group patch, event patch and a couple of freebiees from said event. However, when i look at patchwalls or inside guncase displays i just think 'there is a guns worth of patches there.. ..' Agreed with moaning/not playing. But what i truly dont get is how people turn up to sites late or only start prepping when called out tp gamezone. These people fuck me off the most as i dont understand why you wouldnt get a whole days worth of shooting...1 point -
It would make sense to replace the older NGRS ARs with the new MOSFET and I totally get what you mean too haha. I already built my own NGRS mp5 before TM announced their own version which I've kept in the original A5 configuration with a magpul guard, Was actually easier to convert the TM version to a SD nothing is made of steel so easy to work with. Parts wise you need. SD front sight Guard and sleeve Suppressor I used ICS parts but they are discontinued so it was hard sourcing everything. Your'll need some 35mm steel bar and a lathe for the adapter I made. Also be confident with a Dremel and tap and dye set.1 point
-
Heck yea can they make that a rule where people are only allowed so long in safe area unless injured or damaged gun as you end up with half the team missing else for most of day.1 point
-
airsoft things you don't understand
Akuma121 reacted to JamesAirsofterAgent for a topic
Why people need in excess of 1 hour for a lunch break at a game day. Adult players who get angry when younger/new players are confused or maybe staying a little behind so they dont get hit as much. I don't get what they gain from shouting at these newer players to push up while they themselves, in all their gucci gear, are the furthest back. But most of all, people who pre-fire the hell out of CQB like its CSGO. Pet hate of mine, don't understand what they really gain from it other than looking like a knob and using a load of ammo/gas. Luckily it seems to be mostly a stateside thing, along with their bang bang rule.1 point -
airsoft things you don't understand
Jacob Wright reacted to strykerles for a topic
obsession with the mk23 and throwing stupid money at it when they are mushy and boring but they do have good range 😂1 point -
airsoft things you don't understand
Druid799 reacted to Adolf Hamster for a topic
see i can understand that, you see the reverse with folk in black outdoors, it's just the crossover between majority indoor/outdoor players having a dabble at the other side but can't be bothered buying new kit just to play indoors/outdoors. cmon man, moaning about things we don't like is a national institution1 point -
Fps vs joules and the law
John_W reacted to Adolf Hamster for a topic
that was my point, fps on 0.2j is a joule measurement, just in confusing units that make it seem like it isn't. the reason it's taken so long is because there's not much agreement in chrono standards, for example hop on or off, player weight or site weight, quote limits in fps or j, and sites generally can't be bothered putting too much effort into it, much easier to just remember a number. i've lost count of the number of times i've had to explain that no, my gun is not shooting low, it's heavy ammo, especially when they've set the weight on the chrono and are reading the fps figure (which is always a raw figure of the velocity measurement) rather than the calculated joule figure.1 point -
Fps vs joules and the law
Cannonfodder reacted to Rogerborg for a topic
Reality is a harsh mistress. The only "problem" here is that there are still sites out there who are chronoing like it's 1999. Can you please tell us which sites didn't spot that your toys were shooting hot, so that I can make a note to avoid them?1 point -
Fixed that for you.1 point
-
As the others members above have pointed out: 1. Your M904e is an excellent bit of kit that does all you ask of it. 2. Deep down, all airsoft guns are the same, they fling bb's, some marginally better than others but throwing cash at them doesn't always guarantee improvement. I agree you should have a backup gun, & yes it makes sense that it should have magazine compatibility with your 904, especially if your loadout limits the size of mags you can carry. the obvious plus to this is if one plays up mid game, it's a two minute job to leg it to the safezone to grab the spare, no fuss or time lost 😊. Your 904 is a stubby gun, why not consider one of the longer variants, 907h for example, set it up as a dmr, pretty it up with magnified sights etc, gives you another style of play on a platform that your familiar with, it's what I'd do, especially if my LCE restricted what mags I could carry. alternatively, if that's not the case, get what you like the look of (subject to positive reviews), me, I'm a sucker for the longer battle rifles, m14/G3/SLR, whatever floats your boat 🤔 PS @Rogerborg I'm nicking that picture, awesome, the truth will set them free lol 👍1 point
-
Tokyo Marui Thompson M1A1 (+ hi cap)
TheFedlessHorseman reacted to Tabitha for an advert
Just an option for you to help a sale but the Thompson you have there is the base weapon to creature the legendary M41A PULSE RIFLE from ALIENS/ALIENS 3/etc, etc. The Thompson is the 'hardest' part of the build to find, though it's not actually too rare, it's just that they get purchased alot of the time for either a WW2 load out or to make the mentioned Pulse Rifle. I hope that info / suggestion can get you a decent amount of extra eyes on the gun. Wish you luck for a decent sale. Tabi1 point