Leaderboard

As some of you asked for fotos of my collection, I took a few pics 🙂 We restored a house a few years ago and I got the rare opportunity to turn a room into my personal little "museum". The only downside: The showcases are full already... 😅 As mentioned in the new members thread, I'm a collector for quite some time now and I'm interested in anything that's odd / old / rare / shellejecting / japanese / gasdriven in general and recently got a knack for a bit more steel here and there. Unfortunately, the showcases in the middle still lack lighting 😑 Disclaimer: Everything in that room is legal and according to german laws, the guns themselves aswell as the showcases, which are locked, when I'm not there. The guns outside the showcases are 0.5 joules, so they don't fall under german gun laws, but are categorized as toys.

Pistol from L3wisD, rails from TSAirsoft, RMR from Aliexpress and the torch I picked up in the states a while back.

Hi, ALL! 👋 Going this Sunday to Red Alert, anyone else on here going? See how things go, with possibly a 2nd lockdown!?.... 🤔 This will be my only game in October, see how next month goes, ones better than none! 🔫 💷GAMBLE💷

Arrived an hour or so ago. CM16 SRS in Battleship Grey. This is my new "project" gun. Granted it's currently 3rd in line but couldn't resist at the price.

Cheers, I'm fairly stock internally just an npas that is relevant but the bit I'm really after is the figures as I'm running an original BCG with a bit of saving up for a lightweight option ( is the g&p a lightweight number as I don't like Angry Gun stuff - had a couple of gash items from them). Anyway any knowledge would be great, perhaps if we could nail it down to ballpark figures for a stock gun we could add it the downloadable mws thread document that's on here to cut down on repeat questions as this thread is huge.

I am still trying to figure out how to quote someone as I am new to using forums, but I have the same thing, I think they are so much fun I really don´t care about all the extra stuff that they need done. I have to be careful with wanting more FPS as here in NI we have a law that they cant go over 328fps or 1 Joule which is quite annoying to be fair.

Depends on the site, I played indoor cqb in the winter where the temp was same as outside. You do not need to upgrade internals for mapp gas if you use it when it’s cold - it will have the same effect on the gun as green gas when it’s warm. The fun starts when you’re looking for more recoil or FPS or both and switch to a more powerful gas when it’s warm thus increasing the wear on internals - then you need upgrades. Anyway, gas guns are so much fun I don’t mind the additional maintenance, fiddling with it it’s also part of this hobby (at least for me).

I don’t have any numbers, I can get it to you this weekend if I go out skirmishing as it’s going to be below 10C. Mapp gas brand does not matter, internal upgrades are not needed as mapp gas in cold weather will have same pressure output as green gas on a warm day. But indeed some math should be done here.

same, i mean when you're selling secondhand stuff you're gonna be taking such a loss anyway from depreciation. same with paypal fees, end of the day it's the price you pay for convenience of being able to safely accept money and not worth arguing over. skipping a days shooting is going to save you more money than you're gonna lose in postage+fee's most of the time.

I always give an all inclusive price for anything over £20 and let the buyer ask about a lower price if he wants to collect. Since all but two transactions I've made on here have been posted it makes far more sense to cater to those transactions.

I said “close to 0”. I use 14kg green gas in temperatures not less than 10C. Below I use propylene (mapp gas) and I did not notice any issues.

woah woah woah hold up there, a stock TM MWS with green gas will struggle at 0°C and it's unavoidable. This kind of freezing weather is simply out of the effective operating temperature range of green gas. The chart below says that Green gas/Nuprol 2.0 at 10°C will have a pressure of 5.6 bar/81 PSI which is really weak already, even Nuprol 1.0 says that it operates at 8 bar/115PSI, at it's optimal temperature. I get around 1 magazine of "full power" shots out my a single mag fully gassed up with green gas at a temperature of 9°C. My first shot clocks in at 89m/s (281fps) and my last few end up around 79m/s (256fps) and there is a very significant difference in feel and sound between those first and last shots too. The first 10-15 shots are very consistent, but then the magazine starts to get cold as shit and the fps dips by 1m/s every other shot. Also bear in mind my magazines are the newer versions which supposedly don't require the green gas mod. The saving grace here is that you can simply run higher pressure gas such as red (nuprol 3.0) at these kinds of temperatures. Red/Nuprol 3.0 at 10 degrees will have a pressure of 7.7 bar which is perfectly acceptable for an MWS, and if you're at sub 0 temperatures, black gas is likely your only option or HPA tapped magazines, but lets be honest we're using GBBRs so we DONT have to carry around a damn air tank so that's not an option 😁 Also, you can simply get a light weight/aluminium bolt to improve your gas efficiency in cold weather. There are quite a few options out there too.

https://www.vipertacticalshop.co.uk/viper-tactical-elite-jacket-titanium.html?variation_id=2294 Order a size up to though dude. The reviews mentioned it's a tight sizing and they were right. I ordered a XXL and it fits like an XL. Great jacket actually. I'll get some photos later.

MK18 rail added to my MWS. May get a tan CTR and switch out the grip for a tan RVG. Dunno yet. Judt need some MK18 iron sites now.

Just my AUG on Sunday. Running sweet as a nut so proud owner moment.

Yeah modded mine too. Just annoyed the correct trades didnt come out as well as I was hoping. I did set it up as a Mk3.... but then a few pics arose of the Mk2 type. And was surprised to see still using the looped hammer. So thought I'd stick with the early mk2 until the WE mk3 came out.

#mp5 #staysafe

I'd take one over two aaaany day personally, but beauty is in the eye. T-1 maybe, but I think the 30mm tube classic aimpoints overall have much too much volume/surface area for tiny SMGs I have to say.

Got myself a CYMA XM177 E2 and made a battle belt works a treat also got a PBS4 superessor for the AK.

Finally got around to a family photo... My god, what have I done. My wallet... But it is glorious.

Finally after a month of waiting this gorgeous thing showed up... Northeast Sten MkV GBB. Absolutely beautiful replica, and packs a serious kick. Breaks down almost exactly like the real steel, and operates very similarly. The bolt will even fly out the back if you leave the stock off and fire it, so don't do that. I also recorded a little bit of slow motion-footage to show off the action... I will say one thing though, my second mag seal has already gone, but such are the perils of limited run GBB replicas... EDIT: I've since fixed this issue, the inner gas chamber just needed reseating.

I would much rather see I want £XX amount rather than have to do sums, Just add a tenner for delivery and fees if its a small item and £20 for a RIF. and leave arguing room. Its really not difficult. And dont get me started on the posters who put collection only. And dont put a location *facepalm*