Leaderboard

*Big bag, little gun. *Travel light, leave the spare eye pro, leave the 5 layers, take only as many bbs as you need, *travel in your gear with riding kit over it. *Simple chest rig or belt kit. Don't bother with the plate carrier, helmet and kitchen sink. *Travel to sites that provides drinks better still lunch. I have ridden and it's not too bad, just have to be slick and light. If your m4 doesn't fit in a rucksack, split the receiver into two halfs and even a 16" m4 should squeeze in a rucksack.

I own TM recoil Scar-L, Scar-H and 416. They are without a doubt the best guns I own. Having owned others scars, the TM ones are head and shoulders above them and that's before you even start upgrading them. Absolutely worth the money

You can also get SOPMOD PMAGs which are 120, that's what i've been using on my HK416. I've seen a few kicking about on ebay, although i'm not 100% they aren't clones.

Agree with that I would never buy an ak that looks similar to an M4 in any way.

Cheers guys, still tinkering with the idea of a cyma MP5 but understand the risks could be high. Hmmmm I like the ICS but not the pricetag. will just have to see how things go with savings. Maybe I tell the wife it was the cyma I bought but actually pick up an ICS.......

Sorry to hijack what pouches do you run with the scar h have you any pics of how your scar looks?

Here we go again: Ordered a AirsoftPro reinforced piston for my SVD, the swap-able piston head is a nice feature.

Steel sear arrived, as I expected, it's just a heavy lump of steel. More stuff to come.

As already said above: Most sites will probably tell you to get a one-piece paintball or fencing-style mask, but it's worth asking as the real purpose is just to protect your teeth as well as your eyes for insurance reasons. If they're ok with that then you'll be set.

Yep, I am going Yeah it's mainly a woodland site, but they do have a village or two lol. It's a big site!!! Wear good boots You won't need a pack up, they have catering Take your hits bla bla usual stuff mate

yup - smaller basic fet will do if your gun is not double cycling (AB is an option but imho only if your really need it) I doubt if you will be running a blowback ultra quick yup you gotta open up the box to rewire on V2's decide where fet will go and perhaps use existing wire + 1 extra signal wire at switch (2 posi go on same contact then signal on other running back to fet) try and disturb as little as possible - ensure spring has least tension when you open it 10mm round earth magnet under AR latch and she open quite easily with minimal explosion Would advise AoE or at least look into it, neoprene/sorbothane check piston o-ring seal, cylinder head seal etc.... (if using ptfe tape ensure not to block the port for blowback on cylinder head etc..) possible o-ring nozzle and maybe bearing spring guide if gun is not too close to site fps You lose a bit of fps doing AoE but good seals claw that back spring guide is ok but can add 15 or so fps - hence see how gun shoots fps wise first It is all a question of where do start n stop but most of the above are basic wise tweaks to consider Your gun atm might be running ok - I mean fit deans connectors will help for now and see how she goes as your running 7.4v lipo If and when she starts to play up - THEN open her up to service and mess about with unless you are mechanically confident and want it done sooner than later Just pointing out - if it ain't broke don't try to fix it - well not just yet coz I'd hate to see anybody pop back and say: "where the f*ck does thit bit go ?" or "now she won't fire/feed"

Pico are a good choice. Yes, you will have to open up the gearbox to do the install. If its shooting fine then don't bother changing anything else, if you need a but more fps then consider a heavier spring. There's tonnes of guides on YouTube on how to take apart a v2 gearbox.

Try this version:

If u are a lone wolf like me then this should b for u. https://m.youtube.com/watch?v=BXgrujvpiXU

Buy the November 2015 copy of Airsoft Action magazine, there is a three page article on painting your gun (pages 46-48) with good pictures.

I'd love to make a montage or do a gameplay run to "Badboi" by Pegboard Nerds:

Save some money and do it yourself, it's not that hard

I hear what you're saying but £70 for a "real steel" piece of kit? It's really not much when you look at what you get. Granted the needs of airsofters aren't really up there with actual soldiers so maybe some of us need to lower our sights in terms of how gucci the kit needs to be?

Just make sure what part of the woods you are hiding in, do not want to go scaring off all those out enjoying their favourite dogging site.

Fixed

The problem with masking off trades is that they'll inevitably end up looking a bit rubbish. If you REALLY want to keep it all try and see if you can get decals made (if you have an inkjet printer you can get special paper and make your own). Personally - I wouldn't worry about it.

And the award for best use of airsoft guns and gratuitous sauxy minx goes to....

https://www.google.co.uk/search?q=beta+project+ak&es_sm=122&tbm=isch&tbo=u&source=univ&sa=X&ei=lfV9VIyXHoSXOJ-0geAF&ved=0CC0Q7Ak&biw=1280&bih=685