Supporters Sitting Duck Posted May 2, 2015 Supporters Share Posted May 2, 2015 They are a bit of a bollock ache v2's There are a couple of ways to route the wires in box and in grip most go for the standard wire each side in box but if using much thicker wire and 2 x fet wire's say on a rear wired box it can get a bit cramped by motor, so options are widen box at rear and run both motor wires down back, only fet wires go across motor entry in box G&G default is to run two seperate wires out of both sides of box, then run both at back of grip rather than either side of motor The DSG I ran both at back of box, both at back of grip, one laid low on negative terminal of motor, then positive ran the long way round motor on top of negative Reason being there is a blank or plate on bottom of grip motor plate preventing a shorter direct route - could cut a groove but routed it as was allowed.... It did actually lay quite well - was pleased coz thought it would never fit in on such thicker wire - but it did go in there quite easily in the end - well reasonably easy Still a bollock ache all the same, luckily there are a few options but yes you can solder on a v2 but is regarded as more of pain to remove & service box where as v3's remove frame/motor cage, and you got access to box - even solder/desolder the switch wires without needing to open box fitting a fet on a v3 & upgrade wire can all be done without opening the box - though as we know it don't hurt to crack it open and aoe,seals,grease to ensure she is fet & juice ready...... Yes only worked on a few v3's but I do like them as being a bit more user friendly to work on especially electrical wise & test purposes with motor cage on and test away deffo an improvement on the older v2's in my humble opinion. But that don't mean I prefer AK's over the Fords of Airsoft - M4's (I ain't joining the dark side just yet but admit they got a better build/layout) Ian_Gere 1 Link to comment Share on other sites More sharing options...
BBrotherwood Posted May 3, 2015 Share Posted May 3, 2015 Just picked up a DPCU shirt (AUSCAM) for the start of my Australian loadout. Currently waiting to see if I can get some DPCU trousers from a fleebay seller in Australia as even with postage it works out cheaper then any other alternative I have seen so far. Airsoft_Mr B 1 Link to comment Share on other sites More sharing options...
DX115FALCON Posted May 3, 2015 Share Posted May 3, 2015 My custom Moonman patch arrived from Stitch Me Up earlier this week. Just got my hands on it today. Love it! Link to comment Share on other sites More sharing options...
AirsoftTed Posted May 3, 2015 Share Posted May 3, 2015 I'm going to get a patch that says " Cramped Bed Ted". I'll leave the image upto your imaginations :lol: Link to comment Share on other sites More sharing options...
Supporters Ian_Gere Posted May 3, 2015 Supporters Share Posted May 3, 2015 I want one that says "East Mids Death Squad" but so far I haven't been able to find anyone to design the logo - a hooded skeletal Death drawing the string of a longbow, but facing forwards so the arrow head is massive in forced perspective, not sideways like archers are almost always portrayed, but also not looking like a Scooby Doo villain... Link to comment Share on other sites More sharing options...
Supporters Sitting Duck Posted May 3, 2015 Supporters Share Posted May 3, 2015 soz couldn't resist - mods delete as needed Ian_Gere 1 Link to comment Share on other sites More sharing options...
AirsoftTed Posted May 3, 2015 Share Posted May 3, 2015 I want one that says "East Mids Death Squad" but so far I haven't been able to find anyone to design the logo - a hooded skeletal Death drawing the string of a longbow, but facing forwards so the arrow head is massive in forced perspective, not sideways like archers are almost always portrayed, but also not looking like a Scooby Doo villain... I've give it a crack for you mate. Could you email me a rough sketch so I've got an idea to work from? Link to comment Share on other sites More sharing options...
Supporters Esoterick Posted May 3, 2015 Supporters Share Posted May 3, 2015 Tokyo Marui Recoil Shock Recce rifle Magpul AFG2 Magpul XTM rail panels Marui swivel sling adapter This is going to be an expensive project, glad i'm not doing the tech stuff Airsoft_Mr B and M_P 2 Link to comment Share on other sites More sharing options...
BBrotherwood Posted May 3, 2015 Share Posted May 3, 2015 Oooh I may have sent a slightly shirty response back to the Australian seller after all I got back from him was 'no'. Ian_Gere 1 Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted May 3, 2015 Supporters Share Posted May 3, 2015 Tokyo Marui Recoil Shock Recce rifle Magpul AFG2 Magpul XTM rail panels Marui swivel sling adapter This is going to be an expensive project, glad i'm not doing the tech stuff Im jealous. I keep looking at the Tm recoils but can never make my mind up which one I want. Link to comment Share on other sites More sharing options...
Supporters Esoterick Posted May 3, 2015 Supporters Share Posted May 3, 2015 Im jealous. I keep looking at the Tm recoils but can never make my mind up which one I want. Yeah it was a tough choice but it was narrowed down by the fact I already have a HK416 and a load of PMAGs. I was leaning towards the SCAR but the Recce caught my eye, plan is to get an R Hop fitted plus a load of other internal work by Kingdom of Airsoft. Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted May 3, 2015 Supporters Share Posted May 3, 2015 Yeah it was a tough choice but it was narrowed down by the fact I already have a HK416 and a load of PMAGs. I was leaning towards the SCAR but the Recce caught my eye, plan is to get an R Hop fitted plus a load of other internal work by Kingdom of Airsoft. I love scar h and the 417 but the mags are huge on both which makes pouches a pain. Link to comment Share on other sites More sharing options...
Supporters Esoterick Posted May 4, 2015 Supporters Share Posted May 4, 2015 I like the HK417 but the long variant TM have chosen is not my cup of tea. I'd imagine it looks alright with something on the rails but it was off putting to me. I remember there being talk of TM releasing different variants but i'm too impulsive to hang around for that lol. Link to comment Share on other sites More sharing options...
Supporters Ian_Gere Posted May 6, 2015 Supporters Share Posted May 6, 2015 From ehobbyasia.com SHS Metal Shim Set (Octagon / Circle / Copper Circle) Item Number SHS-SHIM $2.50 USD 1 $2.50 USD RA-Tech Hop Up Stability (Cushion) General Type Item Number RAG-P-002 $7.00 USD 1 $7.00 USD SHS Steel Gear Sector Clip (Delayer) Item Number SHS-DELAYER $2.50 USD 1 $2.50 USD Discount -$0.60 USD 1 -$0.60 USD Subtotal $11.40 USD Postage and packaging $8.00 USD Total $19.40 USD Link to comment Share on other sites More sharing options...
Supporters M_P Posted May 6, 2015 Supporters Share Posted May 6, 2015 I like the HK417 but the long variant TM have chosen is not my cup of tea. I'd imagine it looks alright with something on the rails but it was off putting to me. I remember there being talk of TM releasing different variants but i'm too impulsive to hang around for that lol. It's only a week or so till their next product announcement, they're getting quicker at releasing stuff with every release so could be closer than you think Or we could be let down with a 'boys' 75% replica. Esoterick 1 Link to comment Share on other sites More sharing options...
Airsoft_Mr B Posted May 6, 2015 Share Posted May 6, 2015 Platatac SAS Windproof Smock arrived Was $350 down to $50 Ian_Gere, AirsoftTed, TheFull9 and 1 other 4 Link to comment Share on other sites More sharing options...
Supporters SeniorSpaz87 Posted May 6, 2015 Supporters Share Posted May 6, 2015 I've given in and bought two AFUK Patches, and I will momentarily be buying a custom patch with my emblem (my pic on here). I think Moonman Dan listed a good place a few posts back... Airsoft_Mr B and Ian_Gere 2 Link to comment Share on other sites More sharing options...
clumpyedge Posted May 7, 2015 Share Posted May 7, 2015 x 2 pairs of TMC ranger green combats x 2 TM breacher tanks x 1 breacher pistol grip x 2 packs of white TM shells Airsoft_Mr B 1 Link to comment Share on other sites More sharing options...
Supporters Popular Post sp00n Posted May 7, 2015 Supporters Popular Post Share Posted May 7, 2015 so today i treated myself TM MEU tippmann #0001766 48ci tank Ninja line (some 0.2g bb's which came with the above ... but i use 0.25's) she is epic, amazing noise, RECOIL!!!! cannot wait to try her on the field (though i need to set up full auto at some point, and dial in the hop) ... just adding some rail covers and foregrip Monty, Sitting Duck, Airsoft_Mr B and 2 others 5 Link to comment Share on other sites More sharing options...
Supporters Sitting Duck Posted May 7, 2015 Supporters Share Posted May 7, 2015 nice pistol - lol very very nice one yeah I suppose the "other" gun is alright as a starter gun sp00n 1 Link to comment Share on other sites More sharing options...
airsoftwarrior147 Posted May 7, 2015 Share Posted May 7, 2015 Totally jelly of the the meu spoon, need to get me one soon. sp00n and Airsoft_Mr B 2 Link to comment Share on other sites More sharing options...
BBrotherwood Posted May 7, 2015 Share Posted May 7, 2015 Just brought the F88A2 replica from Evert What I wanted to do with my A1 all along but he has already managed a dam fine job of it He has also been kind enough to throw in the DPCU trousers to go with the shirt which I missed this morning in the post Cant wait to get it and my friend has asked if he could buy the A1 off me before I had even said if I was going to sell it or not Airsoft_Mr B and Monty 2 Link to comment Share on other sites More sharing options...
Supporters sp00n Posted May 7, 2015 Supporters Share Posted May 7, 2015 Totally jelly of the the meu spoon, need to get me one soon. Its nice .... i only wish that the manual was in English airsoftwarrior147 1 Link to comment Share on other sites More sharing options...
Happy Posted May 7, 2015 Share Posted May 7, 2015 Platatac SAS Windproof Smock arrived Was $350 down to $50 Nice find - love this pattern but already have too much gear/camo haha TheFull9 and Airsoft_Mr B 2 Link to comment Share on other sites More sharing options...
CommonComrade Posted May 7, 2015 Share Posted May 7, 2015 KJ Works G32C! Monty and Sitting Duck 2 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now