Supporters Sitting Duck Posted August 6, 2015 Supporters Share Posted August 6, 2015 While my gearbox is open, I'm wondering whether or not I should hard wire the mosfet in? YES IF YOU CAN SOLDER Even just running 7.4v - if you got a neodym motor & lipo for the sake of contacts it should be done coz you will be pushing more juice through it if using existing wire - just make sure it is tidy where the tiny pin passes through box on "normal" V2's Dunno about the jumbo V2's layout - but on conventional V2's keep it tidy behind trigger switch or you might short some wires when you put it back together but yes all them little tweaks do add up to better response in the end - well in my book they seem to do A nice recent purchase was a 14mm CCW tap & die set - high quality engineering from a precision toolmaker (some backstreet pi$$ pot guy with a lathe in the slums of China no doubt via fleabay) Had a few cheap silencers that the threads were a little iffy on all off them - not anymore redid a couple and now they screw up all the way instead of getting stuck halfway down the outer barrel's thread very happy chappy ebay item # 160637665606 - brilliant mofo & ebay item # 160637665354 (not used this yet btw) oh and 2 out of 4 mofo motors arrived as well for smashing hell out of my next gearboxes plus some more dean connectors, stuff for spares box etc...... Zak Da Mack 1 Link to comment Share on other sites More sharing options...
joshcowin Posted August 6, 2015 Share Posted August 6, 2015 Well if land warrior have them in by tomorrow then i will be buying one preferbly the srxl if not i will get a krytac Link to comment Share on other sites More sharing options...
Moderators djben9 Posted August 6, 2015 Moderators Share Posted August 6, 2015 901 chest rig and pouches in Tan.....thanks UKT for the code....Thanks others who pushed me that way!! hahahabest to buy when discounts are on, can always sell on or to brother or ebay later! Lozart 1 Link to comment Share on other sites More sharing options...
Supporters Ian_Gere Posted August 6, 2015 Supporters Share Posted August 6, 2015 While my gearbox is open, I'm wondering whether or not I should hard wire the mosfet in? Definitely - there's not much benefit from a MOSFET unless you do hardwire it. Link to comment Share on other sites More sharing options...
Unrustle_Thine_Jimmies Posted August 6, 2015 Share Posted August 6, 2015 picked these up just now. Absoloute hell cycling to the othet end of Lviv in 35 degree heat. Not the only ones,others were for m8s and not airsoft releated. Cost about 10 UAH for production,and 10 UAH for the velcro. About 80 cents per patch,as they already had the vectors for them Happy, Bottledtorment, Ian_Gere and 1 other 4 Link to comment Share on other sites More sharing options...
joshcowin Posted August 7, 2015 Share Posted August 7, 2015 a krytac spr, we xdm ,dymag hex mid caps (5) and batteries Link to comment Share on other sites More sharing options...
airsofter2015 Posted August 7, 2015 Share Posted August 7, 2015 Where to start since its my birthday i have just spent £360 on airsoft gear an Mtp plate carrier,Milcom boots,2 M4 midcaps,fobus G19 holster,2 batteries,a gun bag,some green gas,We G19,We G19 spare magazine,Mechanix gloves,2 morale patches and a mesh mask. Sitting Duck 1 Link to comment Share on other sites More sharing options...
Supporters Popular Post Lozart Posted August 7, 2015 Supporters Popular Post Share Posted August 7, 2015 It's sooo beautifuuuuulllll........ Sitting Duck, AirsoftTed, Ian_Gere and 2 others 5 Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted August 7, 2015 Supporters Share Posted August 7, 2015 It's sooo beautifuuuuulllll........ Congratulations on your new arrival. Lozart 1 Link to comment Share on other sites More sharing options...
Supporters Sitting Duck Posted August 7, 2015 Supporters Share Posted August 7, 2015 Congratulations on your new arrival. When is the Christening ?? Link to comment Share on other sites More sharing options...
Supporters Lozart Posted August 7, 2015 Supporters Share Posted August 7, 2015 When is the Christening ?? Aug 16th at Our Lady of Plastic Death, Friar Street, Reading. All are welcome to feel it's warm embrace. Unrustle_Thine_Jimmies, Happy, Ian_Gere and 1 other 4 Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted August 7, 2015 Supporters Share Posted August 7, 2015 Aug 16th at Our Lady of Plastic Death, Friar Street, Reading. All are welcome to feel it's warm embrace. Damn not there until the 23rd Link to comment Share on other sites More sharing options...
Supporters Lozart Posted August 7, 2015 Supporters Share Posted August 7, 2015 Damn not there until the 23rd Boooooooo! Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted August 7, 2015 Supporters Share Posted August 7, 2015 Boooooooo! No need for that. Would love to make it but holiday has just cleaned me out. Was going to buy a new backup this month but the kids spent my airsoft fund. Lozart 1 Link to comment Share on other sites More sharing options...
Supporters ImTriggerHappy Posted August 7, 2015 Supporters Share Posted August 7, 2015 Missus did plenty of damage as well. Link to comment Share on other sites More sharing options...
Supporters Lozart Posted August 7, 2015 Supporters Share Posted August 7, 2015 No need for that. Would love to make it but holiday has just cleaned me out. Was going to buy a new backup this month but the kids spent my airsoft fund. There will be other times! I'm fortunate in that I don't have these "kids" of which you speak to spend all my money for me..... Ian_Gere 1 Link to comment Share on other sites More sharing options...
Sacarathe Posted August 7, 2015 Share Posted August 7, 2015 a krytac spr, we xdm ,dymag hex mid caps (5) and batteries What colour mags did you get? I wanted the OD, but not available from UK atm. Got one Black one though. Link to comment Share on other sites More sharing options...
clumpyedge Posted August 7, 2015 Share Posted August 7, 2015 x 3 TM MP7 GBB Mags Ranger Green Dust backpack from Military 1st Semapo Ranger green Combat trousers Flyye Ranger green JPC Link to comment Share on other sites More sharing options...
Supporters Ian_Gere Posted August 7, 2015 Supporters Share Posted August 7, 2015 It's sooo beautifuuuuulllll........ OMGonads, too sexy! Lozart 1 Link to comment Share on other sites More sharing options...
Raffles Posted August 7, 2015 Share Posted August 7, 2015 Tightbore and a few internal upgrades for my 1911 3 extra mags Seal, valve and spring rebuild kits for when the inevitable failures start Yet another protec helmet Link to comment Share on other sites More sharing options...
joshcowin Posted August 7, 2015 Share Posted August 7, 2015 What colour mags did you get? I wanted the OD, but not available from UK atm. Got one Black one though.i got a set of blacks which i wanted anyway Link to comment Share on other sites More sharing options...
Herv Posted August 7, 2015 Share Posted August 7, 2015 I asked the kind chap at Knight's Airsoft Armoury to build me a custom SAI Glock. WE Glock 17 GEN 4 SAI Redbackone Slide SAI Outerbarrel SAI Trigger Kit SAI Guns Modify Minimilist Magwell Mapleaf inner barrel and hop-up Undercutting Striplling RMR Sight + Surefire X300 Replica Torch (not pictured) http://imgur.com/a/VLUen sp00n, Monty, proffrink and 1 other 4 Link to comment Share on other sites More sharing options...
Berto Posted August 7, 2015 Share Posted August 7, 2015 I asked the kind chap at Knight's Airsoft Armoury to build me a custom SAI Glock. WE Glock 17 GEN 4 SAI Redbackone Slide SAI Outerbarrel SAI Trigger Kit SAI Guns Modify Minimilist Magwell Mapleaf inner barrel and hop-up Undercutting Striplling RMR Sight + Surefire X300 Replica Torch (not pictured) http://imgur.com/a/VLUen Apart from the barrel and hop, I've no idea what anything after the trigger kit is, but that is one sexy looking gun. Herv 1 Link to comment Share on other sites More sharing options...
Herv Posted August 7, 2015 Share Posted August 7, 2015 Hehehe. Basically SAI (Salient Arms International) do these for the real steel Glocks and they cost like $2,000. Apart from the barrel and hop, I've no idea what anything after the trigger kit is, but that is one sexy looking gun. Link to comment Share on other sites More sharing options...
Berto Posted August 7, 2015 Share Posted August 7, 2015 Just read up on the stippling and undercutting, makes perfect sense really. And looks the dog bollocks! Herv 1 Link to comment Share on other sites More sharing options...
.gif.c9becc9e80e8b91706ea684ec6e23c92.gif)
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now