Leaderboard

No. That would be fraud

Hi I'm new to airsoft forum UK, and the airsoft game. I bought my first gun (G36C) years ago but never had a chance until nowadays to get a new gun (m4) and actually start skirmishing and I can't wait to get out and do some skirmishes.

That is incorrect. The law states that a RIF or IF cannot be purchased by anyone under the age of 18. It does not matter if you have a defense. If your site says you can despite being under age then they are advising you wrong or you are interpreting what they say wrongly. The only way you can get a black RIF is for someone who has a defense over the age of 18 gifts one to you.

Finally a Silver Madbull Noveske amplifier arrived from Italy, I think this is now as eye-searingly ugly as an M4 can get! Personally I’m quite fond of it, might have to paint some flames on my Atacs gear to complete the “total dickhead” look though

G&G L85A2 with EK3 upgrade kit

Here it is (phone keeps fucking up pictures)

VFC AKS74 and Arcturus Ak-12

Hey bro , your problem has easy solution . Change nub .... a lot of stock MWS come with deformed . Put modify brown VSR and new nub ( for example tube BIC pen ) and enjoy PD : best gram bb´s it´s 0.30 or 0.32

My old King Arms 556 shorty, needs some trick bits but does the job so far 😊

My we scar L gbbr bullpup conversion. this is a Sr union scar h Bullpup kit modified to fit the L

Tm m4a1 gbbr with a few extra mags

Right, grab a cuppa as this is a long one with charts and graphs! So, having found that my current MWS set up was less than consistent on FPS I decided to play about with the parts I had to find the best (ie most consistent) set up available. Quick Notes: RA Black NPAS - Lose fit in TM nozzle, very lose fit in Angry Gun nozzle (probable source of inconsistency) Requires safety-pin to stop it rotating while using special tool to wind in or out. Hard to see in nozzle when adjusting. Angry Gun adjustable valve - Good fit in Angry Gun nozzle, was too large to fit in TM nozzle. Had a drop of superglue added to rear of grub screw to prevent it unscrewing and flying out the barrel! It was a good tight fit in the screw threads so unlikely. Easy to adjust with allen key, nozzle marked "+ more / - less" on the nozzle to aid adjustment RA Silver NPAS - Had been sanded around circumference to fit smoothly in TM nozzle, was a bit lose in Angry Gun. Easier to see when adjusting it, again it requires safety-pin to stop it rotating while using special tool to wind in or out. Things I did not change: Nuprol Green Gas / v2 MWS magazine, unmodified / 0.28g G&G BBs. Modify Tan Bucking / Laylax hop arm / Crazy Jet 250mm barrel. G&P highspeed buffer / SixG HSB / std recoil spring. Xcoretech X3200 Chrono The weather, sunny 22deg C. All tests conducted out of direct sunlight Dynamic Precision green nozzle cup (moved between test setups) Magazine given a 10s charge, left for 30mins. Given a 4s top-up and left for 5mins between tests What I changed: Initially I used the Dynamic Precision lightweight bolt for tests #1 and #2 Test 1: Angry Gun Nozzle and valve, Dynamic Precision nozzle spring. (GREY plot) Test 2: TM stock nozzle, RA Silver NPAS, Dynamic Precision nozzle spring. (ORANGE plot) Test 3: TM Stock bolt with RA Silver NPAS, Dynamic Precision nozzle spring. (RED plot) Test 4: Dynamic Precision bolt, Angry Gun nozzle, Dynamic Precision nozzle spring, RA Black NPAS (this was conducted a couple of days ago, and kicked off the investigation, otherwise all the same) (BLACK plot) Results: Have a look at the two charts, both have the same data, but the scatter graph has the best-fit line added to aid in looking for the most consistent set up. The setup #3 was the most consistent, but changing to the DP bolt(#2) gave almost the same consistency but slightly higher FPS (maybe more gas efficient?) The one outlier at 305fps spoilt it somewhat so maybe over 20-35rds it might be just as good as #3? The TM bolt, due to the extra weight, gave more recoil, but probably at the expense of gas efficiency. I feel this is an acceptable trade-off as the action was still pretty snappy (thanks in part to the SixG HSB) and full auto was still fast enough. The DP lightweight piston probably saves a little gas and can eke out a few more rounds from a magazine but it will likely be marginal and at the expense of recoil felt (if you want low recoil and high RPS....get an AEG!) Conclusions: The TM Nozzle with the modified RA Silver NPAS seems to be the most consistent, it is likely that the bolt (TM or DP) has little bearing on the outcome in terms of FPS consistency. Recoil and gas efficiency is where these make a difference. The TM Nozzle with the RA Black NPAS (built for the MWS system) is a loser fit and will likely have a wider variance, but not as bad as the larger internal-bore Angry Gun nozzle! (I would guess it would be around the 17-19fps spread...maybe one day I'll check!) So, if you use Angry Gun parts...use the whole thing and don't change out valves/NPAS. Or better yet, if other experiences are to go by, just stick to TM! If you are sticking with TM nozzles try the RA Tech Silver NPAS and spend 5mins with some fine wet&dry carefully sanding the external diameter until it drops in and moves freely. If you can find a Black on that is a suitable alternative...oh and in both cases carry a safety pin in your tool box to adjust it

Got one of these for my 50th. Wanted a TAG F1 for more years than I care to think about.

"Finest in town Guv...."