Leaderboard

I have to give them credit for both their honesty and audacity. Not credit in the sense of money though. I would never, ever give them money, the cheeky feckers.

Let's not forget the price, not exactly giving it away, it might be Avenger63's eBay account 😂

Perfect if your a bit cross-eyed lol, prob be spot on.

Shot 33 is good.lol Nice bit of kit you have there.wouldnt like to be too close when that goes off. Why are your targets so high. I would think your shots could go into back gardens. Good vid though. 👍 Regards

I had some issues with my fairly new (sub 2 months old) MWS, that was the hop was shocking and the rifle was so inaccurate. Took it apart and the stock rubber was very deformed as was the stock nub. Replaced with ML Autobot & omega nub..... the difference is unreal! Accuracy is spot on and the range is amazing

Did you test the tnt with the brass nub (sixg)? What about best for running at 1 joule /350fps? Really interested in the results. You’re write up is fab by the way and really interesting. Giving me another combo to trial as the tan bucking just fails far too quickly.

Unless you need feed lips it would seem

Sooo may have not been out playing of late, but i bought a used / not working TM M870 during lockdown months back, sold as leaking and having a hash sawn of job done, plus some vom RIS screwed on. The sweetener for me was it coming with an Angry Gun Gas AR stock, which seem to be obsolete for the most part nowadays. Ordered a few WII TECH & SAT parts at the same time, they arrived a few weeks later from the east. Basically it was leaking between the receiver and the gas expansion/reservoir inlet, a couple O rings sorted that, then that leak moved forward - with the proper pressure in the expansion cylinder - the nozzle was now leaking, luckily id ordered a WII TECH one I also ordered a genuine MESA Remington pump grip and cartridge holder through Brownells. The pump grip took a little bit of TLC with the finger blaster, sorry sander, and gives a much better lump to grip. I did splash out on the SAT steel shortened outer barrel, to remedy the hash saw job, plus it has the nice finish and trades. One bonus other M870 users may or may not be aware of - the SAT barrel has a threaded screw hole to screw the block to up front, this is AMAZING as it does away with that PITA nut plate inside the barrel - if youve taken one of these down youll appreciate how great that is! Also fitted the WII TECH aluminum hop unit and loading nozzle unit, awesome bit of machining that! I then reinstated the pump lock with WII TECH steel parts, works a charm. Well chuffed with it, now it all works properly, its most satisfying to operate, and the shot sound is pretty cool. Will get some nice TM cartridges now it works Oh yeh and when testing / not fully assembled i managed to shoot that3 way barrel spacer into the garden during strong winds, that was novel haha!

My personal unicorn gnu but no way was I paying £400 and never seen one used so had to wait for sale time replaced the stock with a PTS for battery space the Tokyo Marui tracer unit is about 1mm less in diameter a than the stubby supressor so it's a perfect fit. the Tm devgru NGRs and Tm mp7 gbb Can both go now as this feels better to me . think it looks better in night time mode, just need an m lok fore grip daytime Night time Jefftron leviathan with stupid red trigger cos I'm a blingy tart lancer tactical midcaps because kwa and Asg socom mags don't work in this

Ruger 10/22

If anybody is wondering about what bucking/nub combinations are good for the MWS, I have experience with four so far - the stock bucking, the Modify Tan + SixG brass nub, the Maple Leaf MR Hop (60 or 70 degree) + Maple Leaf Omega Tensioner/Modify flat nub, and the T-N.T. TR Hop bucking for GBB (60 degree) + Modify flat nub. Stock Bucking + nub: +Accurate to roughly 40 meters, 50 meters on a good non-windy day and if the target's torso is fully exposed +Doesn't seem to get dirty too quickly, easy to clean +/-Decently durable, but you're limited to under 120 MPS/400 FPS -Can lift up to 0.30's only - nub is too weak -Feels smooth, not as grippy as Maple Leaf buckings Modify Tan + SixG: +Very accurate out to 60 meters or so on 1.3 J, 0.30 - 0.36 G BB's (capable of lifting heavier BBs, up to 0.40, decent accuracy out to 70 meters - not sure about 0.45 or 0.48) +Drop in fit, no need to modify nub - the SixG nub is a good pairing with most buckings on the market +Works very well in cold weather -Not very durable -BBs often curve to either side at the end of travel, some lateral deviation observed -Limited to under 120 MPS/400 FPS, I would not go above 350 FPS in all honesty Maple Leaf MR Hop + Maple Leaf Omega Tensioner: +INSANE range, approx. 70-80 meters accurately with 0.40g and heavier BBs @approx. 2.0 J and above +Very grippy bucking, decently durable, makes a great seal with the nozzle +Consistent FPS +Lateral deviation is noticeably less than Modify Tan/SixG combo -Omega Tensioner needs to be cut at the front and needs to be perfectly aligned or else your gun will shoot way off -MR Hop bucking gets dirty quickly due to how grippy it is and is a pain to get squeaky clean (you'll need to strip and clean your bucking/barrel after every game day) -Very strange issue - has no trouble lazing BBs on semi-auto, but BBs will fall out of the barrel on full auto T-N.T. TR Hop 60 degree + Modify Flat Nub OR T-N.T. standard flat nub: +Not as much range as MR Hop but even better consistency due to shape of patch, insanely accurate (it outranged most AEGs and I was able to score several cross-map kills) +Almost 0 lateral deviation +Doesn't get dirty as quickly, very easy to clean -Need to cut off front of nub in order to fit inside hop chamber -Needs teflon tape to seal better and prevent rotation of inner barrel inside hop chamber due to the bucking retaining edge being a bit thin - took more work to get this one right than the other combos In close to medium range testing (placing shots at roughly 30-40 meters onto a large postcard sized target, about 8x10 inches), the Modify tan combination and the T-N.T. bucking are the most accurate, though at under 30 meters the difference is negligible across all the combinations I've tried and the stock bucking is more than adequate for hitting targets at this range. The main issue I faced with the stock nub and bucking was that it could not lift 0.30s very far unless I was shooting over 1.5 J. In addition, after a while of shooting I noticed a lot of horizontal deviation. I could literally see my BBs making sidespins down to their target and it was getting difficult to thread BBs through small openings. However, past 100 feet is where the MR Hop and the T-N.T. buckings really shine. The MR Hop and the TNT buckings are on another level. The consistency of the T-N.T. from 30-60 meters is better than that of the MR Hop. The MR Hop is a little bit more "grippy." The T-N.T. seems to run cleaner. Both can send 0.40-0.45's out to 250 feet easily. The main issue with the Modify Tan bucking is that it's rated only at 50-60 degree and is not as durable as the TNT or Maple Leaf MR hop bucking. It also has more lateral deviation at long range than the MR Hop or the TNT bucking. There are numerous reports of people's Modify Tan buckings ripping from normal use. I don't see that happening anytime soon with my MR Hop bucking or my T-N.T. buckings. Apologies for the long post. This is just my experience and results may vary from setup to setup.

G&G L85A2 with EK3 upgrade kit