Leaderboard

Now with iris ? 20250505_211136.mp4

Ugliest Ak ever. Lonex gearbox shell + Lonex motor cage Perun Hybrid + clicker Solink 35k Advanced motor (unibearing) 13:1 gearset short stroked by 4 on release Random SHS spring (low powered at 0.88J, but still has silly range) FPS compression parts Begadi Nebo hop unit Maple Leaf 70° Super Macaron Prometheus 6.05x247 brass inner barrel Oddly quiet, does 24 rps on a 7.4v and about 36 on a 11.1v Stock triangle buttstock is too long for my short arms so I'm considering heresy with a M4 buffer tube adapter, or maybe a zenitco style adjustable stock.

Varying levels of QC. Mostly depends on how much profit the brand wants on their BBs. I've seen it with a "local" brand, they were cheap and good at first, then lost the cheap part and now lost the good part as well, to the point I'd rather overpay for G&G bbs instead. A true shame that warhead decided to fuck UK users like this, after all they were a key part of development and marketing in general (Luke pushed them real hard before Solink/T238 took over)

Seeing as it's currently inert and I can't be bothered dealing with it, decided to dress up the MP5 with the A3 stock once more because it looks neat and is practically a wallhanger atm Completely unusable like this seeing as I snipped the front-wiring loom for the solid stock I had on there but maybe it'll go front-wired when it eventually gets a perun [and when I eventually buy a dremel to fit one]

They really don't like active braking, they can stutter etc., and pretty much handle stopping themselves using their own circuitry / speed controller. As the Perun AB++ is an inline MOSFET, it's not an optical controller, it's not smart enough to monitor the cycle of the sector gear. I'd bet an "optical controller" would immediately resolve this, telling the motor to stop at exactly the right time to prevent overspin. I'd try a slower / brushed motor first if one's available, and if all is then good consider your options.

The tube that attaches to the iris is 3d printed so it slides over the end of my tube Cost me £22 per iris and 30 min of 3d printing

The Perun AB++ uses a traditional trigger switch.

After trying to make my own from scratch, with limited success, i gave in and bought the AngryGun KAC silencer with flash/tracer inside. I'll still salvage my attempt and use it on something.

Suggesting an L85 over a SCAR-L is a pretty serious offence, but i suppose we can let it slide once.

Hello Hello, I remembered I had an account here and asked some questions some time ago related to these projects. I figured I'd do a bit of a project dump on what I've been up to. I'll use this thread for future additions, as I certainly have more planned as funds allow. The BR-55 and M7 SMG are near completion and are fully functional. Both need a few tweaks and some internal parts. I'd stopped both projects until January this year, and started both from scratch with the aid of my new printer, a Prusa XL (single head for now). Due to ill health, I had to stop work on the BR, having completed a lot of but not all of the physical aspects, and instead directed my attention to the design work for the M7. The M7 requires a lot less metal work (only cutting some rods and drilling about 4 holes in a 3x12 stainless bar, and a couple in the alu barrel mounting). Thus both are being worked on in parallel. I'm currently in the process of refining a few things. Needless to say, neither project has been particularly cheap. Credit to Kingdom of Airsoft and Perun for the original idea to use the ETU++ as a "DIY" solution. The BR-55 A bit of a mix of The Halo 2, 3, and H2A designs, I went for a mix of aspects due to preference, and deepened the stock to allow fitment of a V3 gearbox. It weighs around 4.5KG unloaded, and is reinforced with 15mm stainless box section within the upper, and 12x3 stainless bar running down either side of the stock. There are various bits of metal rod where needed. Surprisingly it's pretty well balanced on the (very comfy) grip, and will stand on the grip alone unsupported. It's printed very solidly in eSun's PLA super tough. It feels very sturdy and there are no squeaks or wobbles. (old video where it's basically being held together by me, you can also see my H2A Marine helmet). 1:1 to the "real" size. Guts: It uses a perun ETU++ hooked up to various microswitches for operation, and has a proper 3 position selector with a mechanical safety. This means no bullpup trigger bar and a snappy trigger. The round counter is fully operational, utilising Tachyon's solution with a custom graphics pack and modified sensor layout, removing the need for a "sock" on the end of the barrel. The round counter is reset by pulling back the charging handle. Manually (very, very carefully, I swear) removed the sensor and emitter from the board, applied heatshrink, and superglued to a saddle that straddles the hole I drilled in the barrel. Also contains compass and clock. Quite useful for timed games. The gearbox is a V3 LCT AK, with an airsoft-pro G36 chamber and 450 something-mm ZCI barrel. Sadly the ML bucking I used (60' macaron) has given me some issues, and will not lift a .25 without dropping 70+ FPS. Having attempted the usual fixes and various nubs, I'm at a loss. I have a psionic Tho-R on the way for both the SMG and BR, so touch wood that'll be an improvement. The airsoft pro chamber is nice in that it bolts directly to the gearbox, removing that as a variable for air leakage. The battery compartment is in the foregrip, with an AK dust cover style button for easy access and removal. The space is sizeable, and I can't see much trouble fitting at least a 3000mah 11.1v in there (if only I had one). I intend to include a small toolkit. The magazines are fully custom, with ML superfeed springs (hello midcap syndrome). Not perfect, but I'm working on improvements. Thanks to Igniz for some pointers on dimensions. I intend to try integrating AR mag hi-cap guts at some point for a skirmish mag. The mag release is situated in front of the mag well, and gives a nice satisfying click on seating. The well is intentionally loose for the addition of velcro, giving a secure fit. These feed into a modular feed block that interfaces between the chamber and magazine. I've allowed provision for a built in tracer and a mechanism to prevent BBs from dropping. Takedown: Basic takedown is very simple and tool-less. It involves removing the foregrip, removing a detent pin from in front of the trigger guard, then sliding the upper forward out of the 1/3 rifle length grooves. The braided battery cable should slide free easily. Removing the gearbox requires removing the hop from the gearbox, pulling the squished wires out, unscrewing 5 bolts on the back, and feeding it out through the open hole in the back of the stock, followed by disconnecting the deans and microswitch cable. Somehow both better and worse than the AUG. The pistol grip is held in by 6 M4 bolts and I doubt that'll ever go anywhere. Printed and oriented for maximum strength. The entire upper takes down into sections from around the 15mm tube. Other nifty details and gaffes: -There are 6 QD sling points, 2 rear, front and mid (in front of the receiver). -Rubber (TPU) butt pad and coating for the cheek rest. -The cheek rest is too far forward to comfortably use. Game design moment. -The rail is too far forward for most magnified optic's eye relief to be useful. You can however lift the stock over your shoulder to get close enough. -I neglected to put a ledge on the front of the trigger guard, which the fire select detent mechanism attached to. This meant if you put pressure on the trigger guard (say with your hand), it would move the fire select lever up and down. This has been rectified quite easily, if a little wastefully. -I dropped the whole lower receiver onto a concrete corner from several feet while carrying it to the food dehydrator to cure, after the final coat. I nearly screamed in anguish. Thankfully, PLA-ST is very tough, and it sustained only a minor dent on an edge. This is the first battle damage. Remarkable material for being so cheap and easy to print. -I originally intended the design to keep the hop up chamber with the upper upon disassembly. I found that no matter the spring used, firing would cause the hop up to move forward 5mm with every shot. I suspect this has something to do with the anti double feed mechanism it has. It's now fixed to the gearbox, and is somewhat delicate when unsupported by the upper, hanging by only a grub screw. At some point I'll look at fixing it proper to the lower. -The magazines had to be angled forward to be in an optimal position to feed. -I didn't think my power wiring through very well, and it's a bit of a rat's nest. The excess power wires that give sufficient length for the gearbox to be removed have to be stuffed into a hole to keep them out of the way. Not an easy prospect with thickly insulated 14awg wires. Needs improvement. -The muzzle flash is printed and currently just friction fits on the barrel. I've the means but not the expertise to use a lathe to cut a thread into it. When that happens, I intend to buy Foundry's alu flash hider. -The painting was a bit of a nightmare, and contained a lot of stops, starts and bad farts . Accidentally wiping off paint with unintentionally strong spirits, gray overspray onto black, clear clouding, dropping final piece onto concrete... etc. -The detail lines on the stock were so shallow, sanding and spray putty almost removed them in places. Without thinking I set to with a knife, butchering some grooves into several hundred hours of work. -Much like an old warplane being restored with a few bolts or a nameplate being the "same plane", the foregrip was the only part that made its way over from the original project. Considering the detail lines were so small that they didn't even print, I'm kind of wishing I hadn't. I'd say the (almost) end result is worth it though. M7 SMG Ah, the first proper CAD project I ever worked on, and the first airsoft gun I ever attempted. Frankly, the original I started 5-6 years ago was unsalvageable. Looked pretty, but holy moly, what a mess. It's not wasted though, you learn things. I have to say I'm quite happy with how this one turned out. Far less faff than the BR-55, almost everything worked as intended without much trouble. Printed in much the same fashion and material, but a fair sight simpler. (please excuse the mess, Prusa XL enclosed in the background) The guts: JG Vz.61 AEP innards form the working part of this pew pew. Regrettably, AEP performance isn't always the best, and repairing broken ones can be iffy. You can imagine my disappointment when I finally finished a gun that's been 5-6 years in the making, and it has an effective range of 15 feet. The stock bucking applies no backspin at all. Thankfully everything else works, and I have a Psionic Tho-R on the way to help remedy that. The gearbox unfortunately had an incident where the cut-off switch fell off internally, as evidently no thread lock was applied at manufacture. Awaiting a fine torx set to get at it. The feed route is an interesting one, given it goes around 4 bends and finally ends up vertical. Works just fine though apparently. (Note it's a little more noisy than it would be, as there's no barrel or hop unit, or BB being fired) VID_20240811_210834390.mp4 As a salve for the disappointment that may be gripping some of you upon hearing the acronym "A-E-P", this gun's perfectly sized for a P* F2, and would require minimal design changes to adapt it for such. This gun also uses the Perun ETU++, and this time with some wire management (woo). I've got a very satisfying clicky electronic safety that uses magnets as detents, as I had no room to integrate a mechanical safety in the linear trigger. It's very ergonomic and easy to toggle with the trigger finger within the trigger guard. The ETU was intended for this project originally as a way of getting around the lack of semi cut off present on CMG gearboxes (CQB gun with no semi is as useful as a max joule sniper in CQB), but proved perfect for bullpups. The fire selector isn't in the most ideal of locations (under the magazine well), but it can be easily toggled with the off hand. The battery compartment is in the grip, and a cap comes off with the push of a button at the back. It can hold standard sized lipo batteries, preferably short ~1200mah 7.4v. I'm very pleased with the magazine seating / locking mechanism. It was a problem with the original. This time there's a hook very securely mounted to the back of the receiver. As you slide the magazine forward onto the tray, the hook falls into a groove in the magazine, and as the fore of the magazine seats into the mag well, the hook locks the magazine in the X axis as the mag catch locks it in the Y. You can jerk the gun around by the magazine only without play. Nice click too. Both the stock and foregrip change position. The stock extends by around 95mm, and locks securely with a 5mm stainless pin into a 12x3 stainless bar. The foregrip also locks with a metal pin, but into ABS+. It has no side to side play, but has a little forward and back play when deployed. I've decided it's negligible given it's minor and doesn't make a noise. The ejection port / charging handle also works smoothly, though it's not for thick or gloved fingers. The top iron sights are removable, to be replaced with a pic rail. Side and bottom rails can also be added. Takedown: A little more tool intensive than the BR-55 for basic takedown. 2 bolts allow the removal of the upper "cap", 6 more for the inner "block" which houses the hop up chamber, feed block and outer barrel. This slides forward off the nozzle and up. This allows the gearbox, pressured down by the upper cap, to be removed. Nifty details and gaffes: -The stock detent spring has been a source of frustration and fiddling. I've spent some time trying to get the spring mounted onto the pin block. To be improved. -The stock pad is TPU with ABS encased within to mount the 2 QD fittings (designed for single point slings only, unless the front is wrapped with something). TPU doesn't deal with overhangs well, and the quality leaves something to be desired. I'm hoping a second head for the XL will solve this problem (multi-material integration). -The original Omron SS-5 switch I bought for the trigger sounded *exactly* like a computer mouse. I couldn't stand this and instead bought some of the XSS-5 copies that actually feel more solid and sound better. -Surprisingly ergonomic, though the grip is less comfy than the BR. I didn't want to sacrifice the aesthetic too much. The sights are useful for airsoft even if you can only really look down them when holding the gun out like a pistol. You can still align them while shouldered. Adequate for lobbing small plastic balls at other nerds. -The suppressor seems a little pointless for an electric gun, but I'll likely do it anyway at some point. It's very janky and intended to use an olight key ring torch with a threaded "presser" on the back to turn it on. I'd rather do it when I can thread the barrel. It'd also be more useful for a HPA version. Man I love the aesthetic of this thing. Drawing a blank here, nothing much went wrong. I'd hate you less for wanting me to make you one of these. That's about it for now. You may have noticed a new helmet in one of the pics, with built in forehead / glasses fan. Future projects will be the HPA SMG when I'm not poor (gee I wonder where the money went), Mk23 M6C Socom, and a HPA MA5B. We don't talk about the WE tech Glock I turned into a magnum. Needless to say I don't like WEtech anymore. I'd love to daytona a Halo replica, but alas, money. Ask away, just be aware I'm a little closed on specific details as I do plan to make a little money on these. Cheers for reading.

MWS GBBR summer assault load out

Hmm, looking at the ab++ manual you're right they do state ab settings are irrelevant whilst precocking is enabled. Which would imply they're either using an amount, or having none and you just factor in the overrun when dialling it in (ie total precock=intentional overrun+natural overrun). It getting worse with precocking enabled sounds like its naturally double spinning, in which case active brake would be the solution. They mention they have different strengths, which would ordinarily lead to the suggestion that dialling it up would be the next step. The big caveat is i dont know if the warhead would react in the normal way and just do its own thing. Cutoff tweaks might help, the perun is flying blind all it knows is are the contacts open or closed, so if the col is mechanically engaging earlier/later that will change the timing. I remember the old ascu2 i had fun with the col not lifting enough to actually trigger the switch on the mosfet ended up going to the local brick and mortar and rummaging through their box of levers till i found one that worked.

Thanks for the extensive advice! pre-cocking and AB are off and it rarely does it, turning on pre-cocking increases the occurrence. Not tried PC and AB together…I was under the impression that the AB++ couldn’t have both “on” at once (even if the LEDs said they were both enabled, only one was working?) Having run it without the upper receiver on I can see the piston sitting further back each shot until at some points it double shoots. Just given it another test and it was good as gold! Bloody typical! Will still throw an old motor in just to see. Might try a new cut off lever and / or trigger contacts if that fails. It might be down to the cut off nub on the spur gear being a hair different and messing things up. UPDATE: Just tried with PC on 1 / AB on 2 to 3. Still double tapping. No PC and AB on 1 and no double tapping… but the occasional failure to cycle (sad whiring noise!) Just fired 150 times with everything OFF and it didn’t skip a beat! I love transient issues! Thanks for all the suggestions, will keep in mind if it starts playing up again.

that really does sound like the typical precocking tuning adjustment. mosfets like the ab++/warfet run on timers, so essentially they wait for the cutoff lever to trip then add X milliseconds more runtime to the motor (which is what you set when you tune them). if the delay is slightly too long, what can happen is the cycle settles in a different position each shot until that goldilocks position where it runs enough to fire twice. if your box has a window for viewing the piston you can test if this is happening by seeing how far back the piston stops each time, the behavior i'm describing it'll settle slightly further back with each shot until the double fire when it settles further forward and the process repeats. having ab off with precocking can make things a bit more chaotic as motor overrun will happen naturally and can vary from just about everything you can think of (shimming tightness, motor, spring, piston tightness, hell even the grease viscousity or how warm the box is), indeed having too little overrun (typically active braking without precocking) is what give trigger lockups when the system stops too quickly. typically i'd advise ab and precocking together although if you're being conservative with how much precocking is going on it's probably ok to not have ab. you don't usually want ab without precocking unless it's a speediboi build that suffers double fires without it. if you had the precocking really dialled in then i can absolutely see you going from perfection to just barely too long a delay just from a gear swap even if they're the same nominal ratio and shaving a tooth would absolutely do it. sniper delay/dmr mode is just a rate of fire limiter, its only effect is to stop you firing a second shot if you spam faster than it's been told to allow, so shouldn't be affecting this. that said, none of the above explains why it's happening with precocking turned off, but hopefully i've adequately explained why i'd want to be double/triple checking that it is definately off before testing for the behaviour. the other test is to change the amount of precocking, increasing it should make the doubles happen more frequently, reducing it should cure the issue.

Thanks If that's all I need to do to prevent the receiver from breaking then that's not a problem. Also I'm not planning on using anything stronger than green gas so hopefully that'll make it last. I had heard about that. As I understand it, it's a similar fix to mk23 mags which I can do. It'll be for cqb so I'll not bother with anything on the muzzle to keep it as short as possible.

As Kiwi said, the Acetech Blaster M. I've tried to buy one before and they're out of stock everywhere except Evike US and some place in Italy. I'll see what others fit when it arrives.

I'll occasionally get these kind of issues in a build I throw together. There are two things I can usually do to get the system running smoothly. - what I usually do to correct it is try different switch blocks (the part of the switch assembly with the single contact that pushes into the two leaf plate contacts) The little molded L shape groove that engages with the end of the cut off lever can come in quite different shapes and thickness from switch block to switch block. Finding one that works well with your setup can help - note that over time that molded piece can get worn down and squished resulting in slipping and sliding that could just cause the effect you are talking about of a double shot - after all it is a very abrupt mechanical / kinetic flick that occurs when the switch block is pushed out of the channel. - The other side of the same problem is the cut off lever - It's possible that your new sector gear does not bump the cut off lever quite as consistently as your old gears resulting in a slightly tamer (though usually efficient enough) tug on the switch block, resulting in that 'good enough' engagement but just bad enough to give you issues once every 20-40 shots. @ak2m4 posted on FB not too long ago about some precisely machined switch blocks with a nice big square contact - as someone who still has old school switch assemblies in all but one of my AEGs, that's the kind of thing I would love to get my hands on ? I'm guessing if you put something like that in your M733 it might well sort you out.

Acetech Blaster M module is what they come with.

yes, the rear of the upper receiver can crack due to the bolt hammering it over time. Get a sling mount to reinforce the area. https://www.skirmshop.co.uk/mp7-sling-swivel-end-for-tm-mp7a1.html The mags can leak eventually and I've had to rebuild 8 so far by removing the bottom and sealing with silicon. If you go for a MP7 style silencer try before you buy as I've had issues with some silencers smashing the BB's because of alignment.

"Nutropol", as used by the International Dietetics Police.

it means everything is butter smooth in the gearbox, so well done lol. up the spring and short stroke the sector to meet fps. what barrel and bb weight do you use?

It can't've been that unfortunate if you were coming face-to-face with a set of beef curtains. As they say, sex is like pizza; when it's good it's good. And when it's not good, it's still pretty good. It certainly was. ?

You might have to narrow it down a bit, I'm old & post a lot of ? lol. As for "beef curtains", I think it brings back flashbacks from an unfortunate encounter in my youth ?.........? Edit: I just had a look at recent gifs, it was the moobs wasn't it ?

Yep, although I believe there are differences in terms of the level of polishing.

Don't 99% of all bbs come from the same few factories and the only difference is the label on the bottle/bag?

My interpretation was that they will be dealing directly with the factory and selling the same BBs under their own name.

Haven't actually changed the ol' Krytac LVOA-S very much since this pic 5 years ago. Has a genuinely bonkers handguard on it but I put the details on my own site if anyone's really interested. Man those Hexmags were a hype thing for about 2 minutes but were absolutely awful lol..

Said the nun to the bishop

Have you been sniffing dodgy meat products again ? You know you always feel offal afterwards ?

Perhaps it is a pre-emptive apology.

Well in true "fuck you I'm not paying that much" I've made my own NV mount that pivots to the side Used one of the fake PVS-14 body's, ripped the arms off, designed and 3d printed my own arms and now I have what I want

Reading all of this a few months back, all the back story, it was better than Coronation Street ? In a perfect world we'd just have AK2M4 and Negative Airsoft working together to make the pinnacle of UK pro-Airsoft manufacturers / retailers ?

Hello again, It's been a slow few months. The moths inhabit the empty wallet, and the paint is slow to dry in the cold of late winter / early spring. I have since acquired the HPA engine (Scalar Seraph, though I've yet to acquire the tank and regulator. I've started working on the HPA adaptation of the M7 SMG, and will be looking to do do some preliminary thinking and design work for the MA5B (Assault Rifle). Cute lil thing. I reprinted the entire helmet as the prior one was too small for me. I also printed it as one piece instead of 2, out of PLA-ST instead of ABS. I got a significantly cleaner and stronger print. While experimenting with the electronics, it turned out that DC fans usually don't like PWM unless they're designed for it. This means that unfortunately I had to ditch the controllable fan speed for a simple on / off switch. Preliminary sanding done using orbital sander, proxxon pen sander for details, and hand sanding. My fingers and tendons thanked me for buying the pen sander. Layer of Motip spray putty that needs to be sanded right back to the base material. Leaving too much on makes the paint easy to chip / flake off. Unfortunately I spent a lot of time sanding the helmet smooth, painting it with a rather heavy top coat of Maston olive green, before figuring out an alternative finish that I'd rather use. It sealed the deal when I foolishly thought the paint was fully set and I turned it over to paint the bottom. Somehow I hadn't thought of making a helmet stand, and the paint on the top marked from the bubble wrap I'd set it on. I sanded it back a bit before applying the textured finish. The technique I discovered was simply painting over a textured spray paint, which provides a nice textured finish that's extra matt and scratch resistant. Unfortunately this meant I wasted rather a lot of somewhat expensive paint. Comparison between the same paint, both smooth and textured. Rustoleum textured paint. Created a helmet stand for painting without the paint ever touching anything. Overcoated with Maston olive green. Unfortunately the black also didn't fully set, and the masking tape marked it lightly. The lacquer evened it out well enough thankfully. I've never had this many issues with paints not setting even after days, even in the cold months. I had the same paint mark from sitting on fabric weeks after painting. I ended up using a food dehydrator inside a large cardboard box, set to 50'C for 12 hours to "bake" the paint. It seems to work well. Voila. I think it came out rather well. The chin strap was a bit of an experiment, to see whether a fully elastic strap would work. It didn't, it's *too* elastic. You want a little bit of flex to allow your jaw to wag, but too much and it allows the helmet to shift and pull right off your head if you fall. So as you can see there are multiple layers of elastic with some inelastic strap to remove the elasticity rather than ripping all the stitches. I'll certainly change it at some point. I've used a magnetic buckle as I did with my previous helmet that makes it easy to secure with gloves on. Due to the buckle, you can't get a cheek weld on the side it's on. It can be reversed easily, but not something you'll be doing mid game. Getting a cheek weld in general is awkward, but it's the price you pay to use a "sci fi" helmet. It is possible, and better than my prior helmet in most ways. I've also added TPU (rubber) pads to the inside and bottom of the mandibles to stop any scraping against guns to protect the finish of both and reduce noise. The padding is a rather crucial part of this helmet. Not only is it about comfort, but it's about safety too. I see a lot of dodgy custom helmets, and I wanted this one to not be a death trap while running around playing in the woods. I've bought a set of quality D30 pads from a body armour shop, which are amazing at absorbing impacts. Some may know D30 from motorbike armour / padding. These form the primary padding around the skull, while my own DIY padding protects the neck from rotation of the helmet. It consists of 20-30mm of hard / dense EVA foam, with a soft open cell fronting and sewn mesh covering. The fan and battery is integrated in such a way that it doesn't protrude or create any pressure points. The fan is a little louder than desired, but it does actually work to clear / prevent fog if you tilt your glasses slightly so there's a gap at the top for the air to pass into. I imagine it works well for goggles as the top vents would be closer to the duct outlet. The side panels can also be replaced with low profile ones that should allow wide goggles to fit. Key thing for me is it's low fuss, no tubes to mess with, and it's there when I need it. It's a little noisy for running all day, but there's enough capacity in the 18650 battery to do so. Something I may look into eventually is fitting a full face shield, a little like the NMPD police helmets in ODST. The Bolle sphere would be the main candidate as it has a 16J impact rating. One more project I'll be working on is a backpack for my kit and the HPA rig. I wanted to do the hardcase trooper backpack from Halo Reach. This'll be a tall print, using up 359mm of the XL's 360mm build height. I want to add some MOLLE modularity to it. I'll be sewing the straps and padding system, and likely padding out the inside so it's not a rattle can. On another post I'll detail the DIY chestrig I made once I have the chestplate and pouldrons finished up. Thank you for reading, more updates to follow

Old? What an understatement, some have weeds growing out of them!

I think the word is eclectic. Which is good, all for it.

Loving my TM MP5 SD6 but thought I needed to just add a bit of furniture to tart it up so purchased a ASG Airsoft MP-5 G3 Series High Scope Mount in Black, in the hope it locks on securely. Arrived quickly, fitted easily and attached my also recently purchased Vector Optics ‘Frenzy’ red dot. Looks ok me thinks…

This is a shame, it's one that's been on my bucket list for a while, gonna have to try to get a day (or half ?) in before they go. Anyone feel like pushing me around ?

Recent-ish pic of my CAR-15 and delta force kit. Shortly after I went up to my elbows in a ditch and got the gun thouroughly soaked. Had to give it a good airing out in the sun on the dashboard for the rest of the gameday!?

custom gbb workshop walther ppk vfc gbb airsoft

So for those that know my car was (confirmed by the garage) hacked and broken into, and my guns in their case were taken along with my kids tablets. Thanks to the vigilance of this community, the MTR16 has been found, reported and collected, attachments and all, in its case. There are many of you who notified me and my partner and I'd like to thank you all as I had given up and borderline forgot it. Also, having my rifle back means I renounce me quitting the sport. I will be stripping it down and cleaning it and will upload a picture when done. Also this still means the Mk23 and M1014 and tablets are still out there but I have a positive location and am even in limited state planning a snatch back as it were. Oh why don't you leave it to the police I hear you cry, well this is a direct quote from what is a recorded phone call between the police and myself when I asked if they would attend the location with me "Mr (Redacted) I applaud your initiative but we just don't have the manpower. However, you are ex army, you deal with it as you see fit". So there you have it, the tale of tape so far. Again big big thank you to those who got on to me and the missus. I would sign off with a callsign but I stepped away from the AI500 tan team, so I'll use my old nickname from my first days at dogtag, TwoTone out!

Yeah, but if we think about it, impersonating a police officer and carrying an imitation firearm around in the open is nowhere near as bad as calling someone a stinky poopyhead on the internet. Ooooooh, there's some nice flashing blue lights outside my window. I wonder wha-...

Twat got off lightly.

Somewhat productive day in the SkunkWorks. Started off by modifying a silencer/tracer unit, wasn't so fond of the grooves in it and decided to copy the Specter one, but with 12 smaller flutes. Before: After turning the OD down, it was put in the rotary table and flutes were cut with an 8mm ball-nosed end mill. Bit of lousy paint.. And now it looks so much better. Very happy with the result. Next up was a silencer that i bought for my MP5K-PDW. It's some specific type that i didn't realise at the time, but that didn't matter. I made an insert that'd screw on to the threaded outer barrel, but go over the 3-lug QD and sit closer to the front sight block. Turned from 38mm ally, bored to clear the 3 lugs, threaded inside, with an external male thread to fit a tracer and hex flats milled too. It's secured to the outer body with a grub screw. Finished + fitted:

Just a quick update on a few things. The BR-55 had its first game at the start of this month. It worked well for the whole game, though I found afterwards that the V1 Maple Leaf magazine springs I used are useless and lost most of their shape. The V2 ML springs have apparently improved on this, so I'll have to pick some up before the next game. The "squashed" springs should work fine for the SMG magazines however, so no great waste. After a long day it made me realise I need to work on my arm strength more. I've sorted the small problems and sticking points, redesigned the bolt slightly, so it has a nice HK esque lock and slap now (allows a Halo 3 accurate BR reload). Still have one or two little cosmetic details to touch up, but I'd basically call the thing done short of threading the barrel. I had to find a decent cylinder head, nozzle and tappet combo that had good tolerances to stop the midcap syndrome. I still had to shim the tappet and nozzle a bit. I've heard of some people gluing them together, but I didn't particularly want to do that. I also significantly improved the airseal / consistency. Ironically though, having tested it to +/- 2 FPS at home, the moment I got to the site, it varied wildly on the chrono. I suspect it may have just been the first few round in the magazine giving me trouble. Sadly the magwell was too narrow to fit an M4's hi-cap / flash mag internals. I think for future long rifles I'll look at integrating existing magazines into a shell. Small video after optimising the pre-cocking, 7.4v 35C, stock LCT motor and gears. VID_20241029_174825558.mp4 Here's the basic 2 point sling with fast adjustment that I put together. Credit for the design goes to Thrifty Operator on youtube. I'm also working on a new helmet, based on the Halo 3 Marine, specifically the action figure version as it has a sleeker UA plate on the front. I made it detachable as I'd never seen this done before. The helmet looks very much like some of the concept art helmets without it. I've also included a built in 5015 fan in the peak that will hopefully blow air into my glasses. Worst case scenario it becomes a head cooler if I can't duct it efficiently. Unfortunately I was tempted into attempting to print it in plain ABS. I had a spool sitting around that needed using for something. I've never printed anything in plain ABS, only improved, and was not prepared for it. Sadly there was much splitting and warping, and this caused the print of the back to fail near the end. I had to graft on a freshly printed part using ABS sheet mixed into a gloop with acetone. I'm looking at the D30 stealth helmet padding when I can affort it in combination with EVA foam placed where needed to bulk up. It's a little pricy, but worth it for the protection, durability and comfort. See, experience of printing ABS (left), experience of printing PLA super tough (right). Note the many patches of smeared ABS gloop to fill the cracks and bond the two disparate halves together. It'll be a (not so fun) experience sanding into to a smooth finish. That is at least one strength of ABS, the ability to repair and patch it together with its liquid counterpart. Very advanced and certainly not janky method of holding the back of the helmet on while the ABS gloop dried. Trust me I'm an engineer. The ABS as it starts to melt (took a while). PWM circuitboard and battery (yellow) Fan intake at the front of the peak, TPU rubber fan duct (interchangeable. I'm still scrounging up money for a HPA unit, but I'm hoping to have a Scalar Seraph in hand by early next year for building the HPA SMG and MA5. In the meantime, working on this helmet and stuff to sell like my Halo medkits, biofoam etc to fund more projects. The Halo Reach M73 concept art LMG is something I'd also like to pursue. Take care, thanks for reading. ?

Reply from Amazon about the RIF gel blaster. I've escalated it with citations directly to section 38 and 36 of the VCRA, and to the Bri'ish Toy and Hobby Association code of practice. https://new.btha.co.uk/wp-content/uploads/2019/01/Toy-Gun-Code-Jan-2019.pdf I'm frankly astonished that they rejected it: even eBay takes down anything remotely assault-toy related.