AlphaBear Posted April 3, 2022 Share Posted April 3, 2022 6 hours ago, Cr0-Magnon said: I noticed on a warm day and using the drum mag, I was running slightly hot. So have reverted to the stock inner (which seems more than adequate to me anyway). I'm getting very consistent results, just below the joule limit. This one did make me chuckle though.. Blimey! That's bonkers I've a 129mm Crazy Jet with 50deg Flamingo in mine and I've never done a chrono on it... BTW which gas did you use for this test and what temp was it if you could recall? Link to comment Share on other sites More sharing options...
Cr0-Magnon Posted April 3, 2022 Author Share Posted April 3, 2022 (edited) I wouldn't be surprised if yours was around 330fps on. 0.20g. This was done on Abbey Predator. I was going back and forth between indoors and out, testing various weights with the hop set etc. Fair to say not cold conditions though. I will also add that while it obviously doesn't matter in CQB. If you're talking full potential, 0.32g's are probably slightly on the light side. Edited April 3, 2022 by Cr0-Magnon Link to comment Share on other sites More sharing options...
Cr0-Magnon Posted April 5, 2022 Author Share Posted April 5, 2022 (edited) Decided I wasn't going to be outdone by @AlphaBear, so fitted a 129mm AA 6.03 inner barrel. Also I was questioning whether it's worth using heavier than 0.28's, as I'll be mostly using this in CQB/Urban. Getting very good results on this weight though. Oh and loving my new TTI charging handle/fire selector. Oh and before anyone talks shit about my foregrip, holding this with two hands and letting rip with full-auto, is the best fun you can have with your eye pro on! VID_20220405_163604.mp4 Edited April 5, 2022 by Cr0-Magnon Link to comment Share on other sites More sharing options...
Boonie Posted April 7, 2022 Share Posted April 7, 2022 (edited) Can anyone help me out? The hammer broke on my AAP (as usual I guess) so I have replaced it with the cow cow steel hammer, since then the gun has been acting odd. It will jam easily and runs on full auto no matter what I put the fire selector on, the bolt also stays open and gas escapes. I have stripped down, lubed nozzle, rubber, slide etc, replaced both the recoil (cow cow) and nozzle (Waldo) springs but still the same issue, this happens on my HPA and green gas. Any tips? Edited April 7, 2022 by Boonie Link to comment Share on other sites More sharing options...
concretesnail Posted May 21, 2022 Share Posted May 21, 2022 Anyone used these mags for the aap? https://www.airsoftworld.net/a-w-e-glk-18-and-nuprol-raven-spare-magazine.html I need a spare or two Link to comment Share on other sites More sharing options...
Steveocee Posted May 21, 2022 Share Posted May 21, 2022 2 weeks ago I bought another AAP (second hand) 😁 Last week I sold it Call it a moment of weakness, no matter how hard I try to adopt the AAP platform, I just can't 😑 Skara and Enid_Puceflange 1 1 Link to comment Share on other sites More sharing options...
Skara Posted May 25, 2022 Share Posted May 25, 2022 On 07/04/2022 at 10:42, Boonie said: cow cow steel hammer Did you buy the AAP one or just a regular glock hammer? This just arrived Deadly Customs holster for the mamba upper, so I can use my pistol again Link to comment Share on other sites More sharing options...
Hunka1988 Posted July 6, 2022 Share Posted July 6, 2022 Can someone just give a bit of clarity on mag/gas router compatibility. I've got tm g series mag on a primary Airsoft adpater. Will this be compatible with the aap or would I require a nozzle change to a tm spec one? Link to comment Share on other sites More sharing options...
AlphaBear Posted August 4, 2022 Share Posted August 4, 2022 Played airsoft at the weekend just gone and the amount of HPA'd AAP-01's was insane.. It seems everyone is running these on HPA with a mix of Cow Cow and Waldo upgrades! I'm still trying to get my head around seeing a M4 adapter mag on a pistol but hey ho! Cr0-Magnon 1 Link to comment Share on other sites More sharing options...
Stevobeavo Posted August 7, 2022 Share Posted August 7, 2022 Fitted some Waldo goodies yesterday. Should break my hammer in no time 😂 VID_20220806_143323.mp4 xaphor and leadly 2 Link to comment Share on other sites More sharing options...
Skara Posted August 16, 2022 Share Posted August 16, 2022 On 06/07/2022 at 19:56, Hunka1988 said: Can someone just give a bit of clarity on mag/gas router compatibility. I've got tm g series mag on a primary Airsoft adpater. Will this be compatible with the aap or would I require a nozzle change to a tm spec one? AAP's nozzle is proprietary, you're better off with a WE spec router, even better if you can find AW red routers Link to comment Share on other sites More sharing options...
leadly Posted August 18, 2022 Share Posted August 18, 2022 Well after my knocker lock died last year and losing the replacement somewhere in the house, I've found another one on firesupport and installed it last week. So glad I didn't sell this AAP-SMG, as it does put a smile on my face!! Might use it for a few games as an aggressive sniper sidearm at my mates new site, Killzone airsoft on September 4th! @Steveocee Had to tag you in this so you can tell Joe and Gary I'm advertising for them 🤣 Steveocee 1 Link to comment Share on other sites More sharing options...
Steveocee Posted August 19, 2022 Share Posted August 19, 2022 14 hours ago, leadly said: @Steveocee Had to tag you in this so you can tell Joe and Gary I'm advertising for them 🤣 I'll see you on the 4th then matey 😝 leadly 1 Link to comment Share on other sites More sharing options...
leadly Posted August 20, 2022 Share Posted August 20, 2022 On 19/08/2022 at 11:16, Steveocee said: I'll see you on the 4th then matey 😝 Awesome stuff, don't think I've seen you since "the incident" last time we went to Hell's!! Link to comment Share on other sites More sharing options...
Steveocee Posted August 22, 2022 Share Posted August 22, 2022 On 20/08/2022 at 22:02, leadly said: Awesome stuff, don't think I've seen you since "the incident" last time we went to Hell's!! lol My yes. That was a while ago. I'll be there matey.....Orange hoodie and everything. Link to comment Share on other sites More sharing options...
AJMarsh27 Posted August 22, 2022 Share Posted August 22, 2022 Here's me taking my darling for a rip for the 1st time properly since I upgraded it VID_121960422_130256_309.mp4 leadly and DJsnipe 2 Link to comment Share on other sites More sharing options...
clumpyedge Posted September 22, 2022 Share Posted September 22, 2022 Question for the hive mind on these - my friend has just bought one and me not having any knowledge on them couldn't help problem solve. Playing last night and the gun ran fine for the first game or two, suddenly the gun just started venting mags and the nozzle seems to jam up slightly when returning after each shot (then vents) hes tried realigning the hop as that appeared to have twisted slightly out of plum but its still venting and the bolt/nozzle still seems to not be returning properly. any ideas? Link to comment Share on other sites More sharing options...
Skara Posted September 22, 2022 Share Posted September 22, 2022 (edited) The hop shouldn't twist, it's locked to the outer barrel via two screws, and the outer barrel is locked into the upper via another two screws. Remove the upper (there is a big black button on the back of the gun, right below the bolt, push it forward and lift the back of the upper) and check for damage on the trigger parts (specifically the hammer, it's rather weak and it's, in most cases, the first thing that breaks). Also try with a different magazine because AA mags are subpar. Edited September 22, 2022 by Skara Link to comment Share on other sites More sharing options...
clumpyedge Posted September 22, 2022 Share Posted September 22, 2022 3 minutes ago, Skara said: The hop shouldn't twist, it's locked to the outer barrel via two screws, and the outer barrel is locked into the upper via another two screws. Remove the upper (there is a big black button on the back of the gun, right below the bolt, push it forward and lift the back of the upper) and check for damage on the trigger parts (specifically the hammer, it's rather weak and it's, in most cases, the first thing that breaks). Also try with a different magazine because AA mags are subpar. Thanks mate, what mags are generally the go to for the AAP? Link to comment Share on other sites More sharing options...
Cr0-Magnon Posted September 22, 2022 Author Share Posted September 22, 2022 1 minute ago, clumpyedge said: Thanks mate, what mags are generally the go to for the AAP? WE/AW and of course Action Army, work best. clumpyedge 1 Link to comment Share on other sites More sharing options...
Skara Posted September 22, 2022 Share Posted September 22, 2022 2 minutes ago, clumpyedge said: Thanks mate, what mags are generally the go to for the AAP? I use WE/AW mags with red AW routers, they are definitely more efficient than AAs. Sometimes I couldn't get a full mag worth of gas with AA mags. clumpyedge 1 Link to comment Share on other sites More sharing options...
Stevobeavo Posted September 24, 2022 Share Posted September 24, 2022 My mag leaked out the box but I took it apart and greased the o-rings up and its been ok, but doesn't hold as much has as the WE ones. Also try adding a little lube on all the moving parts. Mine came with barely a drop on the gun. Link to comment Share on other sites More sharing options...
Fatboy40 Posted November 14, 2022 Share Posted November 14, 2022 Playing yesterday I ended up boxed into a corner in a maze like building, so used my AAP-01 instead of the AEG and crouched down and made myself small. Got a nice streak of kills, but the pistol was probably way too loud (and on Nuprol 3.0 / red gas). I use a CTM holster so can still use any accessories I want, so I think I need to add a "good enough" suppressor that's not wallet busting, and one that's not too long (no longer than 100mm I think?). Anyone able to kindly recommend one in stock with a reputable UK supplier? Link to comment Share on other sites More sharing options...
leadly Posted November 15, 2022 Share Posted November 15, 2022 I've not checked the stock levels for you but I've got a KAC quick detach suppressor on mine. You can take the foam out and slide a tracer unit inside as well. I'm sure I paid sub £40 for it. It's not going to make a massive difference with it being a gas blow back if I'm honest but I still run one on my AAP - SMG because it looks nice! Link to comment Share on other sites More sharing options...
Steveocee Posted December 1, 2022 Share Posted December 1, 2022 3rd time is the charm then hopefully. I’ve bent and bought another. Patrolbase’s £65 cyber Monday was too good to pass on. Gone tan this time… initial thoughts, looks like a new hammer material from last time. Don’t care as I expect to swap it anyway. leadly 1 Link to comment Share on other sites More sharing options...
.gif.c9becc9e80e8b91706ea684ec6e23c92.gif)
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now