MJ88 Posted April 4, 2019 Share Posted April 4, 2019 1 hour ago, Sawyer said: Thinking about going the block 2 route myself, how was the install? no problems what so every simple & easy solid fit Sawyer 1 Link to comment Share on other sites More sharing options...
MikeL Posted April 5, 2019 Share Posted April 5, 2019 I have (mostly) finished my mk18 build. I’m going to be looking at other torch options, mainly because I’m not happy with the one I have and I’ve also seem to have misplaced the pressure pad! The information in this thread has been really great, just a quick thanks to everyone! The main upgrades are: Laylax 6.03 250mm inner barrel Modify hop rubber Laylax hop arm (will pick up a super nub in the future). Mad bull mk18 rail a low profile gas block and spacer (both of which I can’t recall what they are exactly) Magpul stock, AFG and grip Raptor style charging handle Vortex crossfire red dot with back up irons There was a few issues with fitting the rail that took about 30 minutes to resolve. I’ll add my mistakes here: - The coupling that has all the screw holes does not have a continuous gas tube hole. So you either have to drill a hole, or cut the gas tube down. I would really recommend against drilling the hole, as there is an internal step down that leaves no room for error and you may end up splitting the coupling. I started drilling and then stopped once I realised it wasn’t an easy exercise with the tools I had. - The barrel nut has to be tightened a fair bit to stop the rail from twisting very slightly once it’s on. I also added card shims either side of the tabs of the coupling. The tabs slot against the receiver and the shims gave it a tighter fit. For now, it’s very sturdy and in line. I quite like like the black finish on the rail, but this is preference. While it performs great, i have to say there isn’t hardly any difference from the stock barrel. Although I’ve only done some basic testing. The accuracy of the stock rifle (and barrel) is quite decent. Also, by adding the 6.03 barrel the fps stayed the same (around 295 on 0.25s). I’ll keep the laylax hop arm for now, but will likely get a nub in the future. I know a lot in this thread use heavier bb’s and reach really long ranges, but for now I only stick to CQB and urban sites. I’m quite new to airsoft so that may change few months down the line. I’ll probably end up playing around with it more! Oh and I should also add she hasn’t been skirmish tested yet, but that’s coming up in three weeks. I only have a total of 3 mags though! Wo1f 1 Link to comment Share on other sites More sharing options...
Wo1f Posted April 5, 2019 Author Share Posted April 5, 2019 Looks great! I noticed the same thing with the mk18 rail, that it has the potential to rotate slightly because the tabs are about 2-3mm wider than the receiver. You tend not to notice any real improvement unless you use heavy BB’s. For CQB though, .28’s are more than enough for the short ranges and lack of wind Link to comment Share on other sites More sharing options...
Shifty1303 Posted April 5, 2019 Share Posted April 5, 2019 That does look rly good. Might just go for the black rail too with the brown DD furniture! Link to comment Share on other sites More sharing options...
Johnny C-07 Posted April 5, 2019 Share Posted April 5, 2019 21 hours ago, Wo1f said: This one I’ve got is supposed to be madbull. Does look brown Pretty sure you got a VFC mate. I've a VFC myself and it look exactly the same color. I also got a madbull and this one is definitely not a madbull because off the color Wo1f 1 Link to comment Share on other sites More sharing options...
Wo1f Posted April 5, 2019 Author Share Posted April 5, 2019 13 minutes ago, Johnny C-07 said: Pretty sure you got a VFC mate. I've a VFC myself and it look exactly the same color. I also got a madbull and this one is definitely not a madbull because off the color Nice one. Makes sense as there’s no proper trades on it. It just sits in my parts bin as I’ve never been one for mk18’s😂 Johnny C-07 1 Link to comment Share on other sites More sharing options...
Shifty1303 Posted April 5, 2019 Share Posted April 5, 2019 4 minutes ago, Wo1f said: Nice one. Makes sense as there’s no proper trades on it. It just sits in my parts bin as I’ve never been one for mk18’s😂 Wanna sell it? would go lovely on my mk18 haha Link to comment Share on other sites More sharing options...
Wo1f Posted April 5, 2019 Author Share Posted April 5, 2019 40 minutes ago, Shifty1303 said: Wanna sell it? would go lovely on my mk18 haha Sure. Make me an offer Link to comment Share on other sites More sharing options...
MJ88 Posted April 5, 2019 Share Posted April 5, 2019 what kind of FPS do use get using .36s and what would use recommend for ideal weight of bbs for my mws Link to comment Share on other sites More sharing options...
Sawyer Posted April 6, 2019 Share Posted April 6, 2019 Funny, one moment you think you might sell a gun, then you manage to get hold of the right suppressor for it and that changes... time for some scope rings, an optic and a paint job! After that I'm going to swear a lot while I try and remove the rail, so that I can install a brass nub, and a longer inner barrel. I'm pretty sure it goes less than half way up the entire length of the gun from hop to the end of the suppressor. Link to comment Share on other sites More sharing options...
Kayzeroth Posted April 8, 2019 Share Posted April 8, 2019 Getting Ready for DMR build on MTR16, just ordered the SixG Nub from Dave, also ordered the ORGA LEX05 410mm barrel, but i have a question... what Rubber should i go with? i have read and i think the Modify Tan is the go, i just want to confirm if is the best option what you guys think? will be posting photos of the Vanilla, and the advance of the build including externals!! Link to comment Share on other sites More sharing options...
Davegolf Posted April 8, 2019 Share Posted April 8, 2019 Modify Tan works great with the nub, essentially youre looking for a simple patch contact shape (TM / Modify) that gives the best nozzle seal, the stock TM is great, the Modify seals a little better, so gives better shot consistency. Kayzeroth 1 Link to comment Share on other sites More sharing options...
Wo1f Posted April 8, 2019 Author Share Posted April 8, 2019 The modify tan is a great bucking and a good choice for the orga and SixG nub. Seems like the orga barrel window doesn’t like long contact patches like the TNT or maple leaf. Kayzeroth 1 Link to comment Share on other sites More sharing options...
marine Posted April 8, 2019 Share Posted April 8, 2019 Hey guys any question.... somebody install spring recoil more hard ??? . I had installed buffer hard recoil angry gun and now I feel that bolt release is more slow .... Link to comment Share on other sites More sharing options...
sonofsammo Posted April 9, 2019 Share Posted April 9, 2019 Took my MWS in its HPA drum mag glory for the first time on Sunday - it's a beast and I beast I like very much. BUT I loathe and detest the stock handguard. I find it really uncomfortable - so it's gone! It's a shame the tan doesn't match - but that's what happens when America meets Germany.. I'm gonna just run a single point sling, so I don't have to sully the handguard.The fit is utterly solid and no PTS ring needed. I absolutely love it to bits. EvilMonkee, Sawyer, Immortal and 1 other 1 2 1 Link to comment Share on other sites More sharing options...
Guest Posted April 9, 2019 Share Posted April 9, 2019 1 minute ago, sonofsammo said: Took my MWS in its HPA drum mag glory for the first time on Sunday - it's a beast and I beast I like very much. BUT I loathe and detest the stock handguard. I find it really uncomfortable - so it's gone! It's a shame the tan doesn't match - but that's what happens when America meets Germany.. I'm gonna just run a single point sling, so I don't have to sully the handguard.The fit is utterly solid and no PTS ring needed. I absolutely love it to bits. I absolutely f’king love this build, awesome matey👍🏻 Link to comment Share on other sites More sharing options...
Jacket Posted April 9, 2019 Share Posted April 9, 2019 Just put some MWS specific bits up in the classifieds if anyone is interested 😀 Link to comment Share on other sites More sharing options...
Jimmeh Posted April 10, 2019 Share Posted April 10, 2019 For anyone that is looking for Modify Tan buckings in the UK. Longbow got stock of them a short while ago: https://www.longbowbb.co.uk/product-page/modify-gbb-accurate-hop-up-bucking Davegolf and ThatNordicGuy 2 Link to comment Share on other sites More sharing options...
Cipher-032 Posted April 10, 2019 Share Posted April 10, 2019 Real steel magpul pistol grip. Exterior build is nearly finished 😎 Diesel May have had a paw in on it 👀 Immortal, Wo1f and Sawyer 3 Link to comment Share on other sites More sharing options...
Supporters Prisce Posted April 10, 2019 Supporters Share Posted April 10, 2019 Is it bad I genuinely can’t tell the difference between the pictures? Link to comment Share on other sites More sharing options...
Immortal Posted April 10, 2019 Share Posted April 10, 2019 10 minutes ago, Prisce said: Is it bad I genuinely can’t tell the difference between the pictures? Different crop plus Cat and grip box missing in 2nd shot... Wo1f 1 Link to comment Share on other sites More sharing options...
Supporters Prisce Posted April 11, 2019 Supporters Share Posted April 11, 2019 9 hours ago, Immortal said: Different crop plus Cat and grip box missing in 2nd shot... 🤦🏻♂️ Immortal 1 Link to comment Share on other sites More sharing options...
_FIL_ Posted April 11, 2019 Share Posted April 11, 2019 Greetings all the way from Portugal. Sorry if the english is not that good but as you can probably guess I´m Portuguese. You guys deserve a standing ovation for the truly awesome work and amount of information this thread has and for that I salute and cheer you guys. Got myself an MTR16 last week and only done a game so far with it, but already thinking about upgrading it internally. Having said that I read all posts and almost made up my mind regarding the upgrades I want and only have a doubt on the inner barrel. So far I am thinking on getting this: modify Tan bucking sixg super nub NPAS valve tightbore inner barrel ORGA 6.05mm 410mm or Prometheus EG 6.03/6.00 370mm I am limited to a maximum of 1.3J so I have to be careful with Joule creep and power output, that's why I think the NPAS is a good choice for me. After reading the thread, I now plan to use heavier bb´s as well, starting from 0.25g(which are the ones I currently have around) up to 0.36/0.4(depending on the power output as said above) thus the nub and bucking. The inner barrel is the real head ache here, don't really know which one to take and would appreciate any help you guys could give me. I prioritize range over accuracy but if possible a good amount of both is always welcome, let me know if there can be any changes to the list to get the best out of it. Thanks. sonofsammo 1 Link to comment Share on other sites More sharing options...
Davegolf Posted April 11, 2019 Share Posted April 11, 2019 And you deserve a standing ovation for your English (cos my Portuguese is non existent) and for actually reading the thread! The 6.03 or 6.05 will both serve you well, the FPS variation over 40mm of barrel is negligible. That said are you limited to 1.3J on 0.2g? Link to comment Share on other sites More sharing options...
_FIL_ Posted April 11, 2019 Share Posted April 11, 2019 2 hours ago, Davegolf said: And you deserve a standing ovation for your English (cos my Portuguese is non existent) and for actually reading the thread! The 6.03 or 6.05 will both serve you well, the FPS variation over 40mm of barrel is negligible. That said are you limited to 1.3J on 0.2g? Thank you sir Limit to 1.3J on any bb weight actually...That´s why I have to be very careful with the joule creep. So you don't recommend the 6.00mm? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now