I have no doubt, I just can’t stand the prick
What’s the specs of the rifle? Even when mine was in its semi broke state I could hit something at 75m almost every time
I wouldn’t put limping donkeys BBS anywhere near my gun on the basis of he’s a dick. I’m gonna do some testing tomorrow with Geoff’s .43 and then try something heavier.
@sonofsammo I’ll show you what I did to the nub when I get in 👍
I present you with my thing.
Many years ago, I bought a UFC G36 3.5x scoped carry handle (this scope has seen some shit, pun intended) & absolutely butchered it with a saw to remove the mounting points (a blindfolded monkey could have done better), before using epoxy to stick it to various red dot rail mounts I had 😂 In terms of it being a carry handle, I trust it about as much as a wet fart, but surprisingly it works exceptionally well as an optic. Probably one of the more ghetto things I have done for airsoft, thought I had thrown it away many moons ago! Well, here it is on my SCAR 🤣
I suppose it can sit there until I buy an optic for it... The Vector foregrip will not reside there permanently either.
As a lot of threads end up with one of us recommending the Tokyo Marui MWS, and i get PM's asking about it, i figured I'd start a thread to keep all of the information in one place. Here i plan on covering a general overview of the gun, as well as upgrade parts, general maintenance and tuning. If anyone else wants to share any information, guides or even gameplay with their MWS, here is the place to do it. With that being said, lets get on with it.
I've had my 2 Tm m4 GBBR's for a little over a year now, and they've got through dozens of changes to get them where they are today. Out of the box they are beautifully finished and boast impressive performance. I bought my first one from Zeroone, who price matched it for me. At the time the gun set me back £430 and the magazines £35, but they have risen quite a bit in price in most places.
The gun is incredibly well finished and sports a Cerakoted receiver. Before opening the box, i didn't get what the big deal was about Cerakote, but that all changed after using it over time. The finish is VERY resistant to the hard life I've shown it, and is far more scratch resistant than any paint or anodization on any other gun I've owned. The two I have still don't have a scratch on them. At the rear is a standard m4 stock, which does its job with little wobble, but isn't the nicest one I've ever seen. The railed handguard is very solid and nicely finished with all of the correct numbered markings on the rails. From there you have your usual front triangle iron sight which DOES NOT have a sling attachment at the base.
The magazines hold 35 BB's and have a Cerakoted shell to keep them from scratching easily. They have very recently started coming with silent fill valves, but are mostly the normal kind that hiss when filling and spray liquid propane when full. Its worth noting that the valve sits at an angle to the baseplate. One modification i would highly recommend to do is the "green gas mod" which involves removing a long zinc tube from inside the magazine. This allows more gas into the magazine and upping your shots per gas fill dramatically, with some people reporting 150+ shots from a single gas charge. As a side note, i have started to just cut the zinc tube about 1 inch from the base instead of removing it entirely. A video showing how to do it:
Chronograph Results:
using blaster .20 BB's and green gas i got around 298 fps with a deviation of 2FPS. yes, you heard that right, " FPS. This thing is incredibly consistent!
Important information:
The inner barrel is 250mm on the 10.5 " CQBR and the 14.5" carbine, meaning on the 14.5" outer you can fit a much longer 370mm inner barrel. The Hop up adjustment dial is similar to Tm pistols and can be located inside the upper receiver by locking the bolt back and looking down the magwell. Due to the way the outer barrel is cut, it's not possible to fit an aftermarket rail onto the gun without one of two things. A barrel adapter ring (PTS, ORGA and a couple of others make them and usually cost £10) or A dytac outer barrel, which has a wider lip, as shown below. Dytac on the left
First shots:
I took it down to the 20m range at the First and only shop and loaded it up with .28 blaster devils. They had multiple targets there, but i focused on the little spinning targets at the back wall. The orange discs must have been no more than 1.5 inches in diameter and i was hitting it virtually every time with the iron sights. So far, very impressed with the accuracy. So much so, I treated it to a new dress!
First internal upgrades:
After speaking with Dave about the gun, he explained that the gun wouldnt hop really heavy weight BB's with the standard nub. because it was hollow and squished when applying hop pressure. To remedy this he machined me a great little nub out of brass. Isn't it beautiful!?
This meant i could now lift much heavier BB's increasing my range and accuracy even further than the already impressive stock performance. Using this new nub and GEOFF .32 bb''s i was able to get the bb's out 60+M with a flat trajectory. They were making a 1.5-2ft grouping on the plastic bales as seen in the video below.
I have SOOO much move to cover, including barrel reviews, customs mods and a DMR build, but its 5;30 am and i need to be up in an hour, so we'll continue this tomorrow
The top one is a GR-60 training grenade. By all accounts, they’re so loud you can feel the shockwave even if you’re outside in woodland. Inside it will make you feel sick lol.
below is a T12 thermal imager that I’m going to either side mount or is a flip to the side on my mws.
Wo1f reacted to Rogerborg in Macks airsoft dreamers of the week thread
Wo1f got a reaction from Ropeyshep in THE TM MWS thread
Wo1f got a reaction from Hedzshot in Silverback SRS Thread
Wo1f got a reaction from dom_852 in THE TM MWS thread
Wo1f got a reaction from Tackle in The 'What have you just bought' Thread
Wo1f got a reaction from EvilMonkee in THE TM MWS thread