All Activity

First off, hi! Secondly, the go-to for DMR building is this thread here: https://www.airsoftsniperforum.com/threads/the-holy-grail-of-building-your-dmr-aeg.892/ You're looking for consistency shot to shot in the main. If your hop is struggling to lift heavier BBs and your power is where you want it, there's no air leaks and minimal variance on power between shots then I'd say start with the hop rubber and nub. Maxx and Eon hop units aren't always an upgrade, while they are made to higher tolerances than a lot of hop units, this can work against them if they don't work right in your gun. If you have inconsistent power or you can't get to the power you want with just a bigger spring then you have other issues which will affect the accuracy and consistency of the gun.

Got told off so I’ll be lurking in here from now on 😛

Thank you, this looks very dooable. Thank you, will check it out but it is a bit far from me.

So I stupidly forgot to record what it was chronoing at with my .46s in there but I think it was up to i want to say 2.7 2.8 but that would be a guess. Barrel is clean bucking is in good condition, I guess I'll just have to order a few different springs and see what it comes out like, start with the 130 and go from there!

Thanks (after doing it I thought a dash of tan would have been good as well)

Weapon mounted. Handhelds would be much cheaper. That's a handheld unit with far inferior specs though. Sure it's a thermal, but I'm mainly talking about thermals scopes with a half decent spec list

This! If you do just one thing, do this!

As for not checking any weapons before the first game, I have seen that done at AP and have been checked before the first game.

Please could you make some psg1 furniture for your g3 series?

Can the barrel extension be milled further forward so the hop/inner barrel can be slid forward to clear the nozzle on dissassembly?

Ahh, I get you now. Sorry, it's just that usually it'll be people asking to 'improve' their power by sticking a stronger spring in without doing anything else to it. I'd try it on 0.43 or 45s and see what it comes out at, and then go from there. Without knowing what's in it to start with, I can only guess at using something like an M140 or M130 to start with. I'd also check the barrel is clean and bucking is in good condition before doing anything else.

The quality control on AK rear and front sight alignment is just awful. I have bought at least 6 AKs from LCT in past and I had to return 2 of them because the trunnion pin holes themselves were so badly drilled that the rear sight could never be aligned correctly with the path of the BB. Even when the trunnion is drilled in the right place, the front sight still needs a hammer to adjust it in the right place because the front sight pin holes are not drilled/pressed in the right place. Are there any plans to make this process more accurate? I have never had this problem with E&L AKs. I would love to see the AKM-63 back in the UK

custom gbb workshop Ruger 10/22 22LR 50th Anniversary kj gbb airsoft

Laughing at your mistakes makes you live a happier, longer life. Laughing at your wife's has the opposite effect...

Depends on the rules. I have a habit of clarifying these at briefing. 'What's team A's channel, what's team B's, which is marshal channel in case of emergency.' Listening in after being told the channel to avoid is a dick move. Not knowing the marshal channel is daft in case someone breaks a leg or similar (again). Picking up an unattended enemy radio and sending false info, listening in etc is 100% fine in my book. It's also great fun to use a stupid callsign and then mention what you did around the campfire later that evening... I only play filmsim though.

Budget thermal is a £299 Hik Micro suitable for airsoft ranges.

What form does the unit take hand held. head mounted, weapon mounted? Pics?

Having a warehouse in Czechia isn't going to make things any faster, given you've got to be an RFD to export it from there, so yet more unnecessary red tape. Literally going to be quicker to order from Asia by at least a factor of 2 or 3.

Supply is the main issue, there is lots of stuff I would like to buy especially some of the older models like the SR3M but its always out of stock. I know that production runs are limited but some indication of when things might be available again would be nice.

Wouldn't changing to a Less powerful spring and using heavier ammo just make it a lot more consistent in terms of trajectory and flight? Doesn't look like it's been touched internally I just want it to throw out heavier weighted bbs to stabilise flight without the joule creep that I will get with this power I currently have!

As for time being not . What is comfirmed so far is m60 , hi cappa , mp5 Thanks for feedback ,try to reach out on lct owners fb its easier . Since Jan LCT have eu warehouse based in CZ so it should not be a problem i do agree 2 month is way to much . Regarding box mag i will feedback to them . Optic so far i would say strong no. At the moment all momentum is about M60 and mp5

Are LCT going to bring back the AEG conversion kits and will they increase distribution of their external and internal parts to more shops in particularly here in the UK. so we can avoid going thought a distributor? I have been waiting for 2 months, 20 days for some parts for my lct pkp and I have to chase the distributor for updates. The box mag on the pkp need to be able to use the A&K/Raptor versions and not proprietary ( there a rumour that lct may do a pkm), £202.00 for lct pkp box mag that suffer from number of issue is ridiculous. A revamp of current modules to be more accurate to the weapons they are trying to replicate, RPK74 bipod springs to mind, as it meant to cant a number of degrees to allow for a 45rd mag to be inserted and not mono-pod went at rest. Would lct ever consider replicating combloc optic like the 1p29 scope?

Little bit too regular pattern but not bad, also benefit with some tan.

I'm looking at retailing a decent budget friendly entry unit for ~£730 through my business, just waiting on the unit to arrive for review. Just been upgraded so that now every unit has <18mK NETD value. Built in laser rangefinder and some other nice bits. The spec sheet is the one on the left. It doesn't mention the LRF but my model would have it. Also has a built in ballistic calculator for different rounds. Are people still after thermals these days? What does a "budget" thermal mean to you?