SeniorSpaz87

Sorry, just part of being 'Murican. Means we are smarter than you.

Three part system. Pyramex goggles under a Kryptek Highlander FAST helmet, with a mesh lower face. Its really the angle of the shot. My roommate felt like taking them from a lower angle, idk why.

"Pyramex I-Force Sporty Dual Pane Anti Fog Silver Mirror Lens". Apparently

My "Rifleman" loadout is complete. feat my dorm's kitchen

Scars - have to be tan... And BPup or bust!

And it is done. Mostly. My one of a kind Scar-L. Seen here in it's standard and Thermal versions. God was this a PITA to make... preforms well though. Started out life as a VFC Scar-L, perhaps the best looking Scar out there. Then I got my hands on a SRU prototype kit that is made for WE Scar-L GBBRs. I decided to make the gun run by HPA, as there is no way to get this working with anything other than gas - there is no room for a motor after all. So in goes a Polarstar Jack. I had to whittle down the trigger guard, as the WE apparently has a thinner one - the VFC's was too wide to fit. Then, out came the dremel, as the base of the gearbox stuck out enough that I had to open up space in the stock for it. That took a long time, and is one of the few things left to do (notice in image 3 there is a small gap between the halves - I need to remove about another cm of material). Finally the stock went on (the front half required no modification). I enlarged and angled the hole for the Jack's line next, as the pre-drilled hole needed to move backwards about an inch to work. Next thing - the trigger. This kit extends the trigger of the gun to the front half (obviously). Some light sanding was needed to make the trigger pull smooth. Several layers of electrical tape were added onto the pull face of the trigger's triggering piece, then cut to size, and superglued into place. The triggering mechanism itself was too tight, so the front half of it had to be removed as well. This created the issue of the trigger bar not holding the trigger mechanism, so it was superglued, then the glue seal was broken to create enough surface to create friction so it would catch, but not be permanent (as I still needed to be able to take apart later). Then the SRU kit was done. I put a Venom Tech 6.02 TBB in it, and a Madbull red hop that I had to cut down slightly (that thing is tight...). I also got one of SRU's rails, which I had to cut down with my dremel to fit my Eotech (visible in image 1 and 3) I also had to replace both my FCU wire and my trigger switch, as both had broken somewhere along the way. I added my genuine Eotech 552 with the LBC (Laser Battery Cap), a Knight's Armament QD suppressor, one of my 950 lumen Powertac e5 lights on the right rail, a Contour mount for my facecam on the left, a Safariland single point sling mount, and I use my Gen 1 Magpul P-Mags in a Safariland dual-mag mount. It's taken me about three months to make, and Im happy with the result.

Winter Flecktarn. Niiiiiice

Gotta bump this up. Too important a thread. Sorry Monty

+1 for the Sterling

With a touch of proper English and a smidge of some Asian dialect thrown in for good measure :'D

No.. no it doesn't Ill finish up one of my field gameplays (that you cant really see much as my 7x mobius lens IR filter fell out - so zoom footage is purple and blurred) that has voiceover and you can tell me what you think. *Edit Ill finish it in a few days. A large hurricane is headed into my face as I type, and I will be evacuating further up the coast shortly

But I hate my voice... Especially over microphone

I usually agree. Unfortunately I was kinda 'in the zone' during this particular section of gameplay, so chatter is practically nil. So there isn't really anything you can't hear anyway. Plus, the music just seemed to fit so well with the faster style of gameplay