Jump to content

Davegolf

Members
  • Posts

    2,103
  • Joined

  • Last visited

  • Days Won

    16
  • Feedback

    93.8%

Everything posted by Davegolf

  1. All the best! Keen to get out there in 2021!
  2. Oh they completely serve a purpose, but he can use the leviathan for apples to apples results - IN THAT GUN, or if he built another gun with another leviathan. And the inbuilt metering is way more sensitive than an inline doohickey, unless your on lab spec kit. I mean a BTC is more accurate regarding actual peak current on start up than my Fluke clamp meter. That not a C clamp - damn jarheads
  3. Seriously don’t get hung up on the amps, your leviathan will tell you enough, just a reference point / ballpark device really. Youre not going to get more the 18rps tops out of 7.4, 12:1, 22k. Take it back to bare shell. Does the piston freely fall in the rails when the gearbox halves are bolted up tight? Shimming should be good by now. Tappet plate is not binding. Assemble the cylinder head and cylinder, put the piston assy inside. Blank off the nozzle with your finger. Does the piston pull back without vacuum? Next assemble compression set without the main spring and gears into gearbox, properly bolted up can you easily cycle it all turning the bevel with a screwdriver? This is checking the sector isn’t binding with the piston. Lastly check electrical connections are solid. Let us know what your results are 😁
  4. Haha! Seems like you’ve learnt you have to build the box up and down many times as you go along, testing clearance and motion at every step!
  5. You should have clearance on all your shimming, to allow for lubricant ingress, heat expansion etc. Typically 0.04 - 0.10mm. And you need to do this with the shell halves bolted up properly. Once all gears are fitted, shimmed up, you should be able to whiz them round with your finger driving the sector gear. Driving from the bevel gives you great mechanical advantage, in your case 12x as much Aaaand check for tight spots during rotation, which could point to tooth profile faults, casting marks, burrs etc
  6. Normally quite warm in Flamingos native environment 😂
  7. Is the battery voltage low compared to before? Assuming the spring and FPS is identical to before? Have you actually counted your gear set teeth and calculated the 'actual' ratios? Are the spur and sector mismatched to a bevel etc? (giving you an actually different ratio)
  8. Cheers for that! Completely forgot about Hogue as a brand!
  9. This is a Scar L dude, has 5.56 on the side 😉
  10. You’d seriously fuck your self up with light-chucks!
  11. Fly back diode, eats up the shutdown current created by a DC voltage motor, saves the brushes/commutator
  12. Very nice, what is the base gun?
  13. Very exciting!! Always had great service from Camoraids, hopefully their gaming will bas good if not better! 😁
  14. Very basic setup - Slickster as it comes, IFAK molle’d to rear of one side cummerbund, radio on the other side rear, Ferro KTS M4 up front. Training plates and foam inserts. That leaves 4 free elasticated ‘pouches’ on the cummerbund for smokes/flashbangs, more mags or other randoms. But it’s really low profile that way, can sit down with all, move through CQB with no snagging/protrusion, or wear it under a smock in the field. Really great bits of kit, very adaptable so a great purchase. Pistol, mags and other stuff on my belt. Best Dave
  15. Well if you’re not dead set on Multicam there is a Coyote one in medium at Tactical clothing. I run the 3kg training plates and it’s comfy as hell.
  16. If it helps at all your have a medium, am 40” chest and 6’ 4”, and i have it setup nearly as small as it goes - a lot of room for much bigger chest - not looking to sell it though but just giving sizing reference.
  17. If the problem is isolated to the gun itself - EG it’s not a mag problem - then I would look at the following; - Make sure the piston seal is properly lubed. - A new TM bucking - A new TM nozzle - I know 🦄 I assume your going for full mag dump, so make sure the mag is correctly filled (upside down), non green gas modded, not over filled.
  18. @heroshark needs help I think 🤔 PS glad to see the Derringer is the star 😁
×
×
  • Create New...