Davegolf

@Shizbazki don't worry about inner and outer barrel lengths being close to each other. Try to get upto FPS with a 370mm rather than any longer, it only hurts accuracy. Dont go tighter than 6.03mm bore. @Wo1f had great results at 80M range with his DMR setup.

Did you start reading at the beginning of isolation!? 😂 Have used Defcon before all good from my experience as 0.0001% of there sales prob haha. Camoraids, Firesupport also good UK MWSers Glad your not coming out skirmishing, prob a shit hot shot lol! 😉

What is it, break barrel thing? Pump it up?? What you spent the other £20 on?

Wowza!!

Was expecting M170 😂

Check between the original and new mag for differences. The centre pin looks different in length. Is the gas route rubber the same flowing internally? And is it sealing to the nozzle properly - thinly put some silicone grease on the top surface of the gas route, insert and remove the mag - is there witness grease on the nozzle entry? Is it being held high enough by the mag catch?

Hi @Smiller apologies, yes I am looking into mass production of them, just difficult at this time. I do still offer MWS servicing etc.

At least you know where it is 👍

oooh nothing much, you know propane adapter this, hop rubber that 🙃 You still got that CASV?

Such an effective value levelling system this thread. Also shows just how many forums are actually full of hurtful trolls and so new people cannot see a genuine community past the veneer of this thread due to the common tone they are used too. This is easily the most informative and useful forum around. I suppose this thread actually works unintentionally as a good defensive barrier for the forum, filters the traffic 😁

Issues of a GBBR!?!! There is no difference in accuracy between the two, in actual fact the inner barrel is 250mm 10" on both variants. Pick whichever floats your boat. Food for thought later down the line; a 10" and a suppressor makes for a quiet gun. All you need is; Nuprol gas or propane and an adapter. Some decent BBs, Devil blaster or Geoff's if your flush lol in 0.28g A genuine TM speed loader, 2-3 mags is fine. They are the best gun OOTB period.

Oh yeh this is old, he's showing where he's filed part of the trigger mech for a less stiff / notchy pull and reset. I made a very nice drop in replacement trigger bar that made the trigger lovely with a dream reset, but I couldn't make it cheaply enough yet for you guys. one day! Be great to do a Happy Meal style 'tune your MWS' goody box eventually! I need to get another personal MWS, it's just not right without one 🙈

To tighten groupings; A HSB spacer will tighten up FPS (and therefore shot accuracy) consistency. Bucking clean and dry, all seals good, nozzle and nozzle spring healthy. Mag gas exits in good condition. All that will also alter FPS consistency. To increase range and tighten groupings; If you're nearing 330 FPS or more 0.36s will fly nicely. Higher FPS with heavier ammo again. Otherwise your looking at a higher quality barrel and Rhop

Hi, just stick to a TM bucking, the only time you may notice a Modify is better is in low temps, the softer more silicone like rubber is more compliant and grippy than a TM. This is the same reason why they dont last as long, especially with higher FPS / temps / gas pressure.

Haha @Wild Weasel thinks he's an operator 😉 Basic fault finding, if the problem is with all the mags then I very much doubt it's the mags at fault 😉 Take a base plate off one mag, leave the fill valve in and try it on your adapters, how much gas/liquid comes out?

You probably would get higher capacity again but at the detriment on FPS consistency, and when you can get that many shots from a #2 mag why bother messing about with it 🤷🏽‍♂️

The Glock master has spoken, saw that flow chart and you know... I'm sure it's like a prayer to you @rocketdogbert when someone mentions Glock - you hear it from within 😂 Which is physically larger, the P80 'looks' bigger than the KP13?

Niiiice 👍 I see you like a stipple too 😎 I love a Glock but I find the trigger guard a little small for me, any suggestions?

Cmon then @E21A I wanna see your big pile of Glock 😁

Are you a Glock hoarder or just generally?

This thread just keeps on giving 😁

Have you stripped the valve? it be crudded up or the O ring swollen / ripped / jammed

Lees Precision Engineering make O ring overhaul kits, best sticking with the TM parts 👍