Sitting Duck

Buy an ex-hire, aka "battle worn"
aka used & abused (nigh on fucked) G36 hire gun ???
 
it's ya son's/kids gun - chances are he will ove it or nahhhh don't like it
(so why go nutz on the budget tbh)
 
fuck it - buy a new cheapy and go nutz doing your own paint job even
I'd just go with the simple G36c than other variants - even the metal ris 608-7
(nah - adds a bit of weight up front)
nah - just a basic cheapy G36c so Cyma or JG
(JG's COL in SIG/G36 is a bit diferent to say SHS steel COL

 
JG SIG/G36 COL is silver - SHS reg COL in black with area filed/sanded to show difference
Selector plates are slightly different between Cyma & JG due to COL differences
Cyma's use a reg v3 COL me thinks in their G36's)
 
jusy saying as kids being kids, they'll probably love it or be a 5 min wonder

if you are going to use it a lot say for CQB...
then try to check for entended mag option...
 
 

Not to mention fake jugs
 
I mean when Lola Ferrari croaked
that must been a cremation/coffin to remember
(let alone lift)
 

 
still a struggle to shut the lid I expect

good points there
 
fuck me - prommy buckings are quite bad too
must be the Leslie Ash of bucking lips...
 

 
think there is lesson here that applies to airsoft too
 
just don't go too fucking nutz get some work/upgrades done

Not to mention fake jugs
 
I mean when Lola Ferrari croaked
that must been a cremation/coffin to remember
(let alone lift)
 

 
still a struggle to shut the lid I expect

Imagine mid service, POP.. POP.. 
 
The OP's there like yeee so anyway my gearbox xD

Ohh the smell

What is wrong with people, why can’t they age gracefully!?
I always wonder what happens to the Botox/silicone when you get buried or cremated lol, must play havoc with the burners 😂

fine no problem & about the same on a std gun
if you want a bit of snap upgrade to dean connectors
if you can solder or get a m8 to do it
(cut ONE WIRE at a time or you will get a shock for sure - watch vids on this)
 
capacity, burst C rating can effect ROF
but in general a 7.4v comes off charge at 8.4v full capacity
(cells are 3.7v but charged to max 4.2v, often say 8.35v-ish in total)
so little difference - the 8.4v nimah might come off full charge at say a smidge over like 9v
but is old stuff and doesn't pack same zest as LiPo does
 
so in GENERAL a 7.4v LiPo is about same as a good 8.4v nimah
the one supplied is very lame though just to test out a few shots
really need about 3 x shit ones for a day and easy on spraying bb's
 
or two good Vapex nimah's 1600mah - but most make jump to LiPo
than buy 2 x Vapex's
 
well that's not quite true....
most buy 2 x Vapex's say @ £15 each
then wished they went LiPo instead to be fair

I'd say the 7.4v LiPo is the common battery type we use.  (Get the highest mAh that will fit)
 
RoF may be a bit higher but not much.  It will mainly affect trigger response with a snappier feel as the motor will accelerate a bit faster but won't actually turn much faster.
 
If you want higher RoF then you can change the motor for a higher speed one or...
Some people use 11.1v LiPos with stock guns without a problem but be aware that they put extra strain on all parts so will wear parts more quickly and are more likely to cause a failure of a component.

good points there
 
fuck me - prommy buckings are quite bad too
must be the Leslie Ash of bucking lips...
 

 
think there is lesson here that applies to airsoft too
 
just don't go too fucking nutz get some work/upgrades done

Nick Nack - Golden gun etc...
 

 
 

See this is how it begins.....
 
It'll be 13:1 short stroked before it ever hits the field
 
It can be a rewarding thing getting a gun running sweet especially if you do it with care and attention rather than filling it with expensive bits.
 
The trick with the maple leaf hop rubbers is they seem to have marginally longer feedlips than most brands, great for air seal (and therefore accuracy) but can make it hard for the mag to shove a bb past it.
 
Way to check is to look up the feed tube when the barrel is installed see if there's too much poking out, a little is ok but more than about 0.5mm and it might be causing issues (although normally that's occasional double feeds in a sea of blanks)
 
Generally i keep a pdi w-hop handy as my go-to for guns that dont like ml stuff.

WAIT WAIT WAIT a second...
Double feeding so order new bushings ???
 
First things first - gearbox = pisspot zinc alloy
bushings = steel (sorta)
which material do you think has worn loose ???
(I suspect new bushings may still be a little loose
plus different bushings/bearings will throw shimming out
and all of this is likely to be unrelated to feed issues really)
 
Poundland - £1 purchase of 2-part expoxy
glue bushings in by a LIGHT smear around edges of box - refit & allow to set
 
Double feed or misfeeding ???
 
without going into detail too much...
assuming bb's slip through bucking/hop unit into barrel etc...
(and tappet/nozzle is cycling correctly to feed/chamber bb etc...)
is the mag a little loose in gun ???
 
can you put a bit of cloth (some use velcro - felt part of it, tape)
place a bit of cloth/tape at BACK of magwell, effectively between  gearbox & mag in well
this will very slightly shift the hop forward as the mag is inserted
(very very slightly shifting the mag/hop forward from box which will create a whisper more room
in doing so there will be a slight increase in available room in front of nozzle that should assist in feeding
there is a slight chance that fps "might" lessen slightly but test if it helps with feed issue first)
 
Realistically - wind the hop off, see if gun feeds 101%
if it feeds OK with hop off then things look OK
what "might" be happening is bucking is greasey so not applying grippy pressure to backspin/lift bb
so you wind on more pressure and create jams etc... (often diagnosed as misfeeds - nope it's a jam)
 
is the hop working ???
you don't need to see nub forming a solar eclipse as you look down hop/barrel
it just needs a very slight bump to create backspin
the barrel is 6.03~6.05mm with a 5.95mm bb, you can't have it looking like a stopcock/valve half open
 
tilt gun on its side 90 degrees & fire to see bb's curving right/left = hop sorta working
but if you keep winding it on you'll get a jam in the end
 
The v2 gearbox is cunt for nozzle/tappet tolerances
the tappet fin could be worn - but I kinda doubt it
(plus the cyma tappet is a bespoke bastid)
is the box properly all bolted back into place, with box in position
(be careful tightening the stock tube up really tight, especially in metal receivers - yeah its plastic)
but if stuff is slightly out of whack, nozzle can rub on hop impeding its operating (feed/chamber issues)
 
as said previously - try shit in other gun
test other mags - use good bb's, swap out barrel/hop combo first
basically try a process of elimination/trial n error before steaming in & buying new bushings
(which still might be a bit loose if cheap box allows present bushings to fall out)
 
the tape velcro thingy might assist if shifting the hop forward very slightly
and allow a smidge more room/clearance for bb to slip past the nozzle at full retraction
 
the cyma sector will not allow you to fit a normal delayer, so that suggestion is not really an option
 
stuff like
filing down the nozzle is NOT ADVISED as you will likely lose fps from shortening nozzle
(the velcro/tape at back of magwell will slightly do the same effect but without fucking shit
as you can always remove velcro/cloth tape - but can't put back material you filed off nozzle)
 
it is too easy to steam in and think it must be this - often it isn't
and doubt if bushings will resolve the issue - well not as I can see
 
in your pic, the sector cam was just behind the tappet fin
so it needs to be slightly in front of fin when reassembling
or box won't close
also - might worth rotating tappet spring 180 so the loop is closer to tappet underside/hook
than at the bottom like in your pic - but depends on tappet spring as some have "loops"
formed differently than others. Some say it don't matter which way it is fitted
but on reg trolley switches the loop on the "hook" goes close to tappet underside
to keep the tappet spring closer to tappet in operation etc...
(probably won't make a difference but wondering if spring was fitted that way round)
 
close of Cyma from TWG...
 
looks like your tappet spring might have been fitted the other way around
(might make next to no difference, but the loop is tighter to tappet underside (usually)
than leaning towards bottom of hook)
Most of this is my OCD kicking in - I'd try say the tape in magwell first
before ripping box open, swapping tappet spring around and removing stuff to glue bushings etc...
 
if box was assembled OK then it "should" just work
looks std with no massive amount of wear anywhere
so it "should" work, not as if fucked components or new nozzle too long fitted
so again "should" just work as intended without going nutz
 
some guns/mags like the tape in magwell to reduce wobble and help feeding
it is another kinda bodge/workaround on M4 style guns/mags with sprung/floaty hop units
but providing other hop/bucking/feed/jam issues aren't involved
(hence swap/try the other hop/barrel combo in there from other gun too)
don't go stripping down a hop/barrel combo that works OK - just the complete unit try out
to diagnose what the main issue might be why the sod don't wanna feed too good
 
ps - be carefull with the two black wires getting close to that little hole
that is the where that little pin goes through and if wires are not routed carefully
it is easy to nick/puncture them with the receiver pin - I've done it
(so you learn by our mistakes certain things to take note of next time & stuff to watch out for)
yup - people think v2's are pretty straight forward - well they are but there are a few things to note
and stuff like routing of wires - well basically everything I guess needs a little attention to detail
 
you probably was OK, but just looked a tiny bit close to the pin hole
and like I said I've punctured them wire(s) in the past not checking/routing stuff carefully
 
pps - shims on sector gear go in front of tappet not underneath
but sure you refiited it all correctly - with shims on top of sector gear & tappet fin

twice the fun, literally.....

"POSITIVE VIBES ONLY ???"
OK - that team didn't lose or got its arse handed to them
 
NOPE - they came SECOND (in a two team game FFS) in fact
 
my motto - poke shit at yourself before anybody else does
if you have hurty feelings, or too fragile stay in your safe space/safe zone

Thing is.
It's NOT a copy, it's the same product, made by the same russian tailor using the same materials (albeit different print, KMCS in something, Stalker in M05), only the tag has a different name printed on it
 
Everything, starting from the fact that they steal our oxygen

They realised that clickbait and trolling generates more clicks/revenue than portraying airsoft in a positive light. Most of the commenters on their videos don't even play or own any airsoft guns, they just get a kick out of the footage of full-auto to peoples faces from three metres away etc. If anyone dare suggest it's poor sportsmanship, they're met with a barrage of "Snowflake! You go to shoot and be shot!" (again, by non-airsofters).

"POSITIVE VIBES ONLY ???"
OK - that team didn't lose or got its arse handed to them
 
NOPE - they came SECOND (in a two team game FFS) in fact
 
my motto - poke shit at yourself before anybody else does
if you have hurty feelings, or too fragile stay in your safe space/safe zone

Sound advice given already
 
Congrats on promotion
Well done on getting bonus & recognition
& sounds like you got a level headed missus too
 
as been mentioned, one thing we've all found out, shiney shit means nowt
if you can't get out & play with it/show it off etc...
this lockdown has demonstrated just how materialistic crap is in our life at times
 
 
so no need to let that dosh burn a hole in ya pocket - just yet
ya got guns that work, you got a job with a promotion
and you gotta a woman who understands/accepts (of a sort) she married a big kid
 
plenty to be pleased about without blowing the dosh just yet
congrats again sir

'ere here is an odd thing for you to try...
in your browser bar, type in yourself
than me post a link you think is embedded
 
www . antifa . com (removes spaces, but type it yourself)
 
type in antifa.com and see where it takes you

Sound advice given already
 
Congrats on promotion
Well done on getting bonus & recognition
& sounds like you got a level headed missus too
 
as been mentioned, one thing we've all found out, shiney shit means nowt
if you can't get out & play with it/show it off etc...
this lockdown has demonstrated just how materialistic crap is in our life at times
 
 
so no need to let that dosh burn a hole in ya pocket - just yet
ya got guns that work, you got a job with a promotion
and you gotta a woman who understands/accepts (of a sort) she married a big kid
 
plenty to be pleased about without blowing the dosh just yet
congrats again sir

Bit of a cunt
it is all a bit of a shame
 
it is a clickbait video
bit of sponsorship perhaps...
 
https://www.switairsoft.com/product-page/kwa-m11a1
 
links to his channel/games
at times he plays well has to put up with others not calling hits etc...
(in longer clip - but marshal says he would of hosed them, yeah but there are degrees of hosing)
 
but then he creates a much shorter clip to trigger the haters
but still gets the clicks on YT
 
he could have made a better video to demonstrate the gun
but chose to make one that triggers people - thus increasing his clicks/views etc...
 
at times we have all done dick things - hand on heart
but to make video of it for clicks n stuff - well that is quite sad tbh

'ere here is an odd thing for you to try...
in your browser bar, type in yourself
than me post a link you think is embedded
 
www . antifa . com (removes spaces, but type it yourself)
 
type in antifa.com and see where it takes you

if he ever has a cardiac arrest they would need to hook him to National Grid
as he has zapped himself soooo much a reg defibrillator would do fuck all to him
 
unlike this guy...