Davegolf

The G&P nozzle doesnt lok like it in the best of health! Thinks like the hop unit on the MWS really dont need changing - just sayin for other potential viewers.

Yeh barricade / barrel is a PITA with high HOB if your actually wanting to aim and no present a huge pop-up-pirate

Definitely, being sighted up ready to exploit any opportunity, in urban or woodland setting with a single snap shot .

Well you know the options, it’s upto you 😁 You cannot put a V2 in a V3 platform

It’s rum, always rum 😂

G&P mags are the only ones I’m aware of that I haven’t tried/tested. Once again they prob all come from the same factory anyway!! Be very weary of gas routes that are too tall, they will press up against the nozzle are really mess shit up.

Yeh TM are undersized, they guesstimated the dims from pics. It’s so annoying!! Love a full size KWA, but they are crap compared to TM performance.

Not sure why you compare 50rd to 20rd, stock mags are 35rd. But hey 🤷🏻‍♂️ The real test is how many shots can you get from one gas fill? Aye the stock bolt deforms on the hammer reset, but only so far, it work hardens. In all honesty TM could have put a steel chip there. Non the less the stock bolt works perfectly for 10s of thousands of rounds. I do like a lighter bolt, it has many benefits. But the rollers on the G&P are unnecessary as the bolt centrally locates to the buffer part ‘A’. And with the buffer spring/tube/assembly lightly coated with Moly grease it works very slickly. RE your problem; using the stock TM mag as a pattern, line the mag catch detent up with the ProWin mag, and look for discrepancies in the height of the upper plate, feed lips and gas route. You will most likely have to file/sand some shit down.

Just in case you didn’t know: Shim each gear individually, fully screwing the gbox case together to check for clearance / free spin. Once you’ve done them all add one at a time a re screw gbox and test. That way if you get a tight spot or meshing issue you’ll know what caused it. If you get a tight spot check teeth don’t have any burrs, sometimes there are manufacturing errors. With the bevel and pinion roll them in your fingers, some combos don’t get on. PS it’s worth fitting the bevel only, then the motor with pinion to setup the height etc, then also power the motor to check fine tune.

Guy on the left looks a lot like Paul from Prison Break I mean its not cos he was born in '69 but v similar

The best solution but completely impossible 'cos AR' would be to have the stock dropped, that way you keep low HOB for less disparity / hold over variations, an upright aware stance for active shooting, but the best bit - you could just lift up a cheek riser for prone shooting no? Or the other solution that already exists that they seem to have forgotten about is;

Sorry i couldnt help myself... only a couple years back all the AR fappers were bitching about the likes of many other firearms with a high height over bore optic line, you know because people actually have necks, and now without any apology they are all over it like they invented it - i mean thats never heappened either 😆 Discuss

"ProWin mags as they are superior in design, performance and handling with a G&P bolt carrier which, again, is superior in every aspect. - My question therefor was if anyone can help with the combination as the carrier seems to hang up on a part of the mag." Sorry couldnt help myself - contradiction right there. Most people are only bolting stuff on because they want to be different or they need a replacement part and they gave someting else a try. There are some good aftermarket parts, but as you have found they inveitibl always need fettling to make work correctly, they are not true drop in. So when it comes down to it next to no aftermarket parts give actual perfromance gains, just vanity points.

Hello, Bolle Pilot are the best OTG by far, especially at the price. You didn’t say what he’s using already though? You can always carefully cut a little relief in either side for the arms to clear.

The TM MP7 is a cracking gun, accurate, fast and loud… what more could you want 😎 Well some would argue size I suppose 👀

Yeh sometimes the post/reply button needs pressing more than once, hopefully it wasn’t a long ad!!

Go to your profile and look for ‘activity’ > ‘content I started’

@SSPKali skylar PSML!! @scar527 well done your trigger box is now run in! Strip it, clean it, deburr and smooth everything, oil it up and you’ll have a whole other level of trigger time enjoyment. Can you say wall/break/reset 😁

Perfect ‘The Purge’ loadout IMO 😎

Go big or go home 😂

Looks like the pinion doesn’t get on with that bevel. If you can get a Lonex helical/spiral bevel & pinion kit.

AK105-VSU (11.5” barrel) I really enjoy making paint and environments work, spent a lot of time and collected a lot of Cerakote swatches and loads of aerosol tests. Some colours are very ‘reactive’ and play to the human eye changing quite dramatically in different light and backdrops.

I think you’ll look star studded by the end! 😂

I always remove the rubber disc from inside the cylinder head 😉

Most AEGs want 4-5mm depending on squishyness