Jimmeh

If they are putting it in an AR receiver block in the vice then you should be all good- if they are trying to put it straight in the vice then I’d be very worried. 

If they are putting it in an AR receiver block in the vice then you should be all good- if they are trying to put it straight in the vice then I’d be very worried. 

The way I remember it, and bare with me here........ is this:
 
If you were to hold the rifle as if in the aim and rotate the rifle around the wheel, and keep the wheel still... the rifle will point upwards and the wheel won't have moved relative to you. That way makes the BB's go up i.e. more hop.

At the time I was using 0.36g Longbows and ASG Ultrair (might have been Guarder Black if it was cold).

So cost including shipping is 4198HKD which is approx £435. You’ll pay 2.5% duty on the cost of the item and shipping which would be £10.88. You’d then pay VAT on the cost of the item, The shipping and the duty which would be £89.18. Therefore your total cost would be £535.06. If you were lucky for customs not to charge it then you’d be better off, if they do then you’d be worse off. 

When it comes to red dots.. something to bare in mind. If you have an astigmatism in your eye(s), you will never see a clean dot. One of my friends didn't realise that he had one and just assumed all red dots were a little blurry. 100% recommend the Vortex Optics though - they are worth every penny. 
 

Hi and welcome to the club!
 
No tools are required to maintain as such but to strip parts, in the event you need to, you will likely need some screwdrivers, barrel nut tool, and a magazine valve tool.  The width of the buffer tube is mil spec but the style of it is commercial spec - I have put a mil spec Magpul CTR stock on and it fits lovely! Most should fit, some might be wobbly or very tight. Trial and error.  Its not real steel spec - has to be MWS specific, but PTS do a MWS Radian charging handle (have it on mine and its very nice) Yes. I have a Magpul K2 on mine - have to use the original MWS bolt. The thread on the receiver is AEG spec, so anything for an AEG should fit, but you will likely need to buy the barrel adapter for your barrel to work with an alternative setup. It replaces the rubber nub in the hop chamber - it gives stability - worth doing for lifting any weight. 

For anyone that is looking for Modify Tan buckings in the UK. Longbow got stock of them a short while ago:
 
https://www.longbowbb.co.uk/product-page/modify-gbb-accurate-hop-up-bucking

For anyone that is looking for Modify Tan buckings in the UK. Longbow got stock of them a short while ago:
 
https://www.longbowbb.co.uk/product-page/modify-gbb-accurate-hop-up-bucking

“Gimme a sec”

I have thought about having a DMR version but a lot of sites here have a 30m MED, so its too far. If it were 15 then I think I would do it, because I will get to use my pistol more.
 
My advice to you is to stick with normal assault, but I would advise against a longer inner barrel. It will make it a lot harder to lower your FPS to a legal level, especially on heavier BBs. The NPAS works, but only to a point. After a while, it becomes unstable and the FPS drops through the floor. 
 
To lower my FPS I have tried NPAS, Low Flow Disks, and G&P adjustable low flow valve. I'm still not happy that I am below the 1.13J I need to be, but I am getting there with tweaking. 
 

Put a heavier BB in and you’ll creep closer to the equivalent energy of 350 on a 0.2g. 

I think there are special clubs for people with weird tastes like you....

I think there are special clubs for people with weird tastes like you....

If I remember rightly, it dropped my FPS by about 20-25 over stock!

So from what I’ve managed to piece together, red will give higher FPS, green gives low. Each of them have 3 settings to dial it up or down. 
 
Earlier in this posted, someone listed his results with the red which were useful. 
 
I purchased a blue blue and green. The green is in my MTR on the lowest FPS setting and it’s managed to bring it under the equivalent of 350FPS on a 0.36g BB which even the NPAS struggled with! 
 
Edit: read from here: 
 
 

With Brownells, import taxes etc should be included in the price so you shouldnt have to pay them.

I think that the “MWS Club” is really the “ZET system club”. As long as it’s a TM GBBR then we are all friends. 

I think that the “MWS Club” is really the “ZET system club”. As long as it’s a TM GBBR then we are all friends.