PopRocket123

Thanks, not a bad idea. I could dress it up as a peq box or range finder it something

Fair enough, thanks guys. I'll have a look at the mancraft kit for it but I want to try doing an msr kit for it which wouldn't leave any space in the stock

Has anyone tried the co2 bolt? It seems to me to be a much more cost effective option than upgrading everything else

Pretty sure you can still find the blood spatters of you look. In fact you can work out exactly how my duvet was by lining up the splatter

I've injured myself more messing around with my guns than actually in a game. My worst two are when I was carving out a rail cover with a scalpel to fit a pressure switch and I slipped and stabbed myself in the end of my thumb. On instinct I shook my hand and splattered blood across my room from corner to corner. The other one was when I was using a flat head screwdriver to tighten a barrel nut and it snapped and went into my ring finger. It actually severed a nerve which I had to push back into the hole. I still have a strip of numbness in that finger.

I think with the loading gate if there was a two part feed system that could work. If you had a midcap that came up to the loading gate to load into, then the loading gate could be a block with a feed tube up to the feed lips. Either that or I'm overcomplicating it and it'd be better just to load it by opening the bolt and loading them straight into the feed lips.

I've had an idea for a gun and I need you lot to tell me how doable you think it is. I want a green gas Winchester repeater so I'm thinking if you had the gas in the stock like a TM M870 and an integrated mid cap magazine in the magazine tube that you can load from the loading gate with a speedloader. Then you have the bolt and lever system like a normal single action gas gun and the trigger under the bolt with the trigger connected to the hammer and valve knocker behind the gas route through the grip. And you can have a rotary or tdc hop up. How doable do you think this would be?

AliExpress ￡10.36 | Tactical URX 3 & 3.1 Deluxe Panel Kit Rail Mounts Accessories Rifle Scope Mount For Hunting https://a.aliexpress.com/_mLo2jnH

Technically have made anything yet but it's nearly ready to start printing parts

At this point it's basically finished, minus going back through and making sure all the parts will fit and have the right spacing.

Someone from my town is proposing a local airsoft site. Do you think the community is better off with more smaller local sites like this or are a few larger sites with higher player counts and bigger budgets? Personally I'd like to see more local sites with local communities.

Nice one, thanks. Yes I'm right handed but I don't have the money to buy a rs post right now. I was looking at printing one but there's no good way to do it as it wouldn't be strong enough.

Where did you get that front qd sling mount from? I'm after one for my build

Not as impressive as all your custom rigs and holsters but here's mine. My partner goes through hairbands like you wouldn't believe so I took a couple of the stretched out ones and used them to secure my grenades to my belt. The spoon goes through the molle and the hairband goes over the top and hooks on the pin. They're nice and secure now and, with a bit of practice, just as fast to unhook. VID_20200824_222113.mp4

I lost a very hard to find KSC M93R mag the same way.

Apparently no one on Facebook has any imagination so I thought I'd ask here. I'm working on a custom AEG using a mix of printed parts and bits I've got lying around but I can't decide on a look. Anyone got any inspiration? I want to build something totally unique and sci fi.

We have the ACP9 as well now

Funnily enough I'm not happy with it. I'll have another go at some point, see if I can do better.

I seem to be spending more time designing than actually printing at the moment

This was in my town this week. I have no hope left.

Folding monopod grip for sniper and DMR stocks

I love interesting sci fi guns but all of the non-rif Airsoft guns all look pretty terrible to me. There's that thing that looks like a G36 let itself go, the anime M4, Ares SOC and the pulse rifle and that's kind of it. So I've resolved to make my own stuff from now on since I have a printer, a bunch of spare parts and no disposable income to spend on new guns. I've already started work on a sci Uzi AEG and I've got plans for a rifle, bullpup and l96 stock.

I want to print a taser that takes one of these. I think that'd be great fun to have with a police loadout.

For mounting buffer tubes to things I use RS buffer tubes and thread them in. Way stronger in a printed part

I got my suppressor mount for my USP C printed. Really happy with the look but of course I messed up the dimensions of the fittings so it doesn't fit. Bugger... Also got my first order for the SCAR rail printed.