sp00n

Imax b6 ;-)

Question:- I have 3 mags for my we g18c, there all filled with the same gas and bbs, yet 1 of the mags, ridiculously over hops bbs. (And I keep forgetting which mag it is) All mags hold gas, with no leakage etc Any idea why? (Posted from mobile so no red)

Another pair of heroshark mako's in olive drab

There is no "best" don't get me wrong g&g are really really good, and for the money there combat machine series is really epic, I have one and recommend them. but like most manufacturers g&g do have lemons (like there gbbr's, avoid them like the plague!!) Overall TM seem to be the most consistent across there entire range (pistols, aeg's gbbr's etc), even if a little lower on fps.

If these weapons are to be wall mounted etc, why not get two tone then just spray the visible side black?

No it's just a standard v2 with a hell of a long nozzle lol

Hmm you will probably want a 130'ish spring but I am not 100%. And I am not sure where you would get one, as I don't think anyone makes them. Try sending ASPUK a message on there Facebook, see what they say

Almost forgot I have the upgraded steel cylinder and cylinder head, as the stock TM cylinder wouldn't have lasted long with my build.

Bear in mind that the stock trigger isn't that good, on the TM version anyway, yours might be ok, but a 500fps will stress the trigger What fps are you aiming for? Also the x-fire springs linked to above are designed for upgraded Pistons, so may not fit yours.

Yeah that sounds the same as a stock TM l96 In my tm l96 aws I have upgraded to a AirsoftPro 90degree trigger, the AirsoftPro 2015 piston set, and a pdi 200 vsr spring (as the m160 that comes with the piston kit is too hot, but I am told that if you clip 15mm off it it's fine) The pull is smooth as silk with the pdi Spring, and with no hop, I am getting 342fps with 0.43's, but I am still bedding the spring in, so I expect this to drop another 5-10fps to make it perfectly site legal etc.

I am lead to believe they are TM l96 aws clones (according to ASPUK's webby) What you need to do is to measure the current Spring :- length, internal diameter, and external diameter

Just want add my g&g sr25 had 8mm ball bearings, but the ratio was abit high for my liking in any case it's jacked now

Spoke to them, even sent them a pic or 3, but no free fcu cables for me they linked me to amped airsoft who has them for sale etc Also am looking at stock options, as I want something different, but I have not seen any thing that I like ATM

Been looking on the airsoft sniper page on Facebook ASPUK have been a little well give them a call/message mate

Yep, I am going Yeah it's mainly a woodland site, but they do have a village or two lol. It's a big site!!! Wear good boots You won't need a pack up, they have catering Take your hits bla bla usual stuff mate

With the current version of fcu, I don't believe it's an option. Future versions maybe

I should also add that since my gun is physically locked to only safe or semi, I would not need to adjust any settings (such as rof or any of the full auto functions etc), once setup

Yeah I have been chatting to p* for abit (that's how i got a jack patch , and I found out about the sr25 nozzle) I'll drop them a message see what happens

updated main post, and finished .... sort off

What dose the nozzle look like? Any nicks on it?

What brand and weight of bb are you using?

i would advise maybe looking at lipo's as these have a very low internal self discharge vrs nimih. what charger are you using?

i use the viper belt with a osprey yoke, nice and padded, gets the job done

considering it would need a 90degree trigger upgrade if your aiming for 500'ish fps, and lets face it hardly anyone one dose the sears upgrade these days. and it hasnt been used in along time etc, hop rubber and other seals may be shot .... it seems a little over priced