Azman1978 Posted September 4, 2017 Share Posted September 4, 2017 Afternoon all. Right gun in question is a G&G gr25. Standard v2 gearbox with elongated hop unit and cylinder head nozzle. Done so far: Mosfet fitted (nano) and fully rewired to deans connectors. Prommy 590mm 6.03. New g&g green bucking. M125 spring Shs high torque motor. Polished the cylinder Rebuilt and fully shimmed the gearbox. All good but only getting 245fps on .2g bbs at the mo. Probably a miss match on the barrell length so looking for a bore up set with no luck due to the cylinder head design. Any advice? Or how would others do it? P.s gun pulls the spring with ease and no noise from the gb. No air seems to leak up the mag bb port when firing. Cant think where else to go. Oo what grease do you guys use in the cylinder? Thanks in advance. Really want this fixed as it was an awesome gun just needed a tad more range. Hoping to get to the 80m mark. Link to comment Share on other sites More sharing options...
Supporters sp00n Posted September 4, 2017 Supporters Share Posted September 4, 2017 Quick test, (with gun fully unloaded) invert gun, put some tissue over the magwell, fire gun if tissue moves I would have a look at the spacer/adjuster on outside at the rear of the gearbox Link to comment Share on other sites More sharing options...
Azman1978 Posted September 4, 2017 Author Share Posted September 4, 2017 Tissue does not move. Link to comment Share on other sites More sharing options...
Hangtight Posted September 4, 2017 Share Posted September 4, 2017 If you have a shorter barrel to hand, try that. At the moment you have over 50% too much barrel for a full cylinder using 0.3g BBs. Link to comment Share on other sites More sharing options...
Azman1978 Posted September 4, 2017 Author Share Posted September 4, 2017 Will revert back to the original and give that a go tomorrow. Post back shortly. Thanks Link to comment Share on other sites More sharing options...
Azman1978 Posted September 5, 2017 Author Share Posted September 5, 2017 Barrel changed to original. 300 fps. Got to be an air leak somewhere. Link to comment Share on other sites More sharing options...
Hangtight Posted September 5, 2017 Share Posted September 5, 2017 A silicon grease will be fine for the cylinder. Try the paper test again but with a finger over the end of the barrel. Are you doing your fps checks with the hop wound off? After that check the cylinder/cylinder head/piston seal. How long is the stock barrel? And have you checked your chrono against another? Been got by that one before! Link to comment Share on other sites More sharing options...
Azman1978 Posted September 5, 2017 Author Share Posted September 5, 2017 Think i have nailed it to the piston seal. Did the paper test no movement. Stripped down to gb and taken apart. Cylinder head seal is fantastic. Finger over end and blowing in the other with no leak. Piston seems very loose. Putting finger over end if nozzlr when together yhe piston still fires so must be air going round piston head seal. Original barrell length 509mm. New fitter is 590mm Link to comment Share on other sites More sharing options...
Azman1978 Posted September 5, 2017 Author Share Posted September 5, 2017 Chrono is good as getting 335 fps on my delta recon. Link to comment Share on other sites More sharing options...
Hangtight Posted September 5, 2017 Share Posted September 5, 2017 Try a 363mm barrel with a full cylinder firing 0.32g BBs. You may find you actually need to come down to a 120 spring once you get the efficiency up by getting the cylinder/barrel ratio right. Link to comment Share on other sites More sharing options...
Supporters Sitting Duck Posted September 5, 2017 Supporters Share Posted September 5, 2017 A std v2 full barrel is really for a 455mm barrel YES - I know the G&G SR25 is 509mm & think some others like a G3 long mofo as well as a a few others come with 509mm barrels but it really is pushing it for volume If pushing the volume ratio then even correcting AoE can screw you up If OP has corrected AoE he might need to consider only "half correcting AoE" (improving it slightly but still need as much volume on that stretched volume limit) As for bore up kits I personally wouldn't really bother coz if you do the maths it don't boost it that much The std cylinder is about 23.8mm inside and an inch or 25.4mm = a wall of about 0.8mm Can't make the outside much wider or the box won't close & the walls not too thin either So when you take all into consideration percentage wise it doesn't boost the volume much at all The AoE throws or reduces the stroke more than a bore kit will replace imho So you have to work with what you got which is likely to be: 101% perfect seals - G&G piston heads are not great - bordering crap imho the o-ring nearly always is a bit crap, try some other o-rings to get compression as close to perfect (sealing straight away etc... to attain compression straight away or as near as damn it) All other seals you say you have checked etc.... As been mentioned it is your volume to barrel and not a great deal you can do about the volume just keep stroke as much as possible - half correct AoE or certainly not full or over correct AoE get the piston seal perfect & try a shorter barrel to match the full std cylinder - max 455mm I know some G&G SR25's shoot well but imho they must be tweaked to perfection, zero leaks tbb barrels still no more than 509 if not 455mm - or they converted to HPA The volume & maths & crap are pushing it all way out of the usual tolerances It is why other longer AEG's like other SR25's use the longer v2.5 or SVD or G&G/AA L85's etc... and use a longer piston cylinder gearbox for 509+ barrels Think G&G created the SR25 just for looks without really thinking it through and decided to wing it with a v2 box Long waffle - but get compression/seals beyond perfect coz you need all the help you can get Only half correct AoE at the most as you are struggling Try a shorter barrel than chuck money into a bore up kit which imho won't boost volume much in the end Link to comment Share on other sites More sharing options...
Azman1978 Posted September 6, 2017 Author Share Posted September 6, 2017 Only bummer is cant change the cylinder head unless i manufacture one. Ordered a ss cylinder and new piston. Going to play with this a bit to get it right. Will probably gasket seal the cylinder head in place. If that does not work i may be looking for a 2.5 gb shell and swapping some internals over lol but at least i will have some bits for when the nuprol gb goes. Will keep posted when the stuff arrives and i have finished with the v2 gb. Ah also ordered a double o ring piston head (shs) to give that a wurl for compression seals. Link to comment Share on other sites More sharing options...
Azman1978 Posted September 8, 2017 Author Share Posted September 8, 2017 Kk folks. Update. New cylinder, piston and piston head installed. Compression is excellent. No air leak including with air nozzle on ( already has o ring in the air nozzle). Put back together and did a few test fires. First 10 shots 345 fps (0.2g) average ( with the longer promy barrell). Thought i would change to the oe barrell to see if that made a difference. It did. Dropped the fps down to 287. Ok. Swapped back to the promy barrell and then was getting 245fps again..... what the hell is going on???? Any ideas. Possibly the hop unit not sealing well enough. Using green g&g bucking. Help. Want to get to a game jn the next few weeks. Link to comment Share on other sites More sharing options...
Supporters Lozart Posted September 8, 2017 Supporters Share Posted September 8, 2017 My initial reaction is that it's a problem with the way you're reassembling the barrel into the hop unit. Link to comment Share on other sites More sharing options...
Supporters Samurai Posted September 8, 2017 Supporters Share Posted September 8, 2017 Check if the nozzle is in the centre of the barrel. Fire the gun so the nozzle is halfway back, not blocking completely the BB's path. Remove the battery and mag, get a flashlight and shine it in the magwell, where the BBs go up. Look down the barrel and you'll see if the nozzle is centre or not. Link to comment Share on other sites More sharing options...
Azman1978 Posted September 8, 2017 Author Share Posted September 8, 2017 Dont seem to be able to feel a seal when mating the hop to the gearbox.. starting to feel this one may be past me. Replaced all sealing parts acept the cylinder head as no replacement units available. This is doing my swede in. Link to comment Share on other sites More sharing options...
Azman1978 Posted September 8, 2017 Author Share Posted September 8, 2017 Samurai. Cant do what you have suggested. The gr25 has a hop unit that mates fully to the gb. Link to comment Share on other sites More sharing options...
Azman1978 Posted September 8, 2017 Author Share Posted September 8, 2017 Sorry was in dim wit land for a moment there. Right. Just done the paper in the magwell test and no movement other than gun vibration. Did what samurai suggested and the nozzles looks fairly central ( looking down 509 barrell) Link to comment Share on other sites More sharing options...
Hangtight Posted September 8, 2017 Share Posted September 8, 2017 What happens if you try the paper test with a finger over the end of the barrel? Link to comment Share on other sites More sharing options...
Azman1978 Posted September 8, 2017 Author Share Posted September 8, 2017 Still fires. No movement of paper. Link to comment Share on other sites More sharing options...
Supporters Sitting Duck Posted September 8, 2017 Supporters Share Posted September 8, 2017 I have serious doubts if your M125 spring is anything like what it should be you should be hitting 410+ fps most likely 425fps or more with longer tbb the variations & losses are down to seals at hop/nozzle/bucking sealing 101% it is blowing if the nozzle doesn't seal 101% this is why you was getting all sorts of results and got 345 then swap this n that the hop/barrel was reassembled badly perhaps and so got 287/245 like Lozart & others are saying I'm just also wondering is that spring anything like a m125 coz even @ 345fps on a good day you are way out even if volume is out a bit (not a hell of a lot though not high enough volume for 0.30's) you should still be hitting 400+ fps - no honestly it is way out imho If 345fps was your best and all was looking good that spring is a m105 tops imho I know this is additional crap but your spring sounds iffy as well to me Is there any way you can get the spring tested or fit another that you know is deffo m125 that is if you are aiming for 425fps dmr ??? if you are trying just for 345fps regular aeg then ignore this post and concentrate on the hop/bucking area but that m125 spring you say is in there is way out need to get back to 345fps so reassemble hop again and fit the unit to gun carefully the alignment of box tilting back from overtightening the stock tube etc... is a right pain to watch out for basically if not careful the front of box can tip up and then nozzle scrapes at top of hop unit and crap seal The M4's AEG's have a number of bastid qwerks and issues and can really do your head in on top of the hop issue of blowing and a good drop in fps Soz to chime in but that m125 spring is also looking suspect to me if the best you got is 345fps so far Link to comment Share on other sites More sharing options...
Supporters Samurai Posted September 9, 2017 Supporters Share Posted September 9, 2017 A few years ago I serviced an AK where I couldn't find the reason for a loss of 100fps for many tries. Everything looked perfect. It turned out that it was the piston O ring (and cylinder and piston head combo). Testing them manually it was perfect airseal. With a finger on the cylinder head, I couldn't push the piston in. It was shooting 300 fps. Then I switched to an O ring that had very little resistance when testing manually. The piston was just slowed down a little. With that it shot the required 400 fps. When it was shooting full speed, the O ring squeezed too much between the piston head and cylinder wall and slowed down the piston. The one that felt too small on the manual test didn't expand that much on full speed, thus it created the perfect airseal. It was one of the more unusual cases. Link to comment Share on other sites More sharing options...
Jay91 Posted September 10, 2017 Share Posted September 10, 2017 My gr25 had a sudden drop of about 70 fps on a game day, stripped it down and turns out the nozzle had an a leak. I used Teflon tape around the o ring as a quick fix and a test to ensure this was the cause. Got to be worth a try hth Link to comment Share on other sites More sharing options...
Azman1978 Posted October 5, 2017 Author Share Posted October 5, 2017 Hmm. Fed up with it now. Have bitten the bullet and ordered an a&k v2.5 gearbox (elongated) for a good price and a prowin hop unit. Bit of tinkering and see if that fixes the issue. T least i will have more air to mive heavier bbs. Link to comment Share on other sites More sharing options...
Hangtight Posted October 5, 2017 Share Posted October 5, 2017 Beware the Prowin. Often the cause of more problems than it ever solves. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.