Jump to content

Are 11.1s correct for my gun after the work that has been done to it???


Wegalaxy
 Share

Recommended Posts

Hello,

 

So I own a ARP 9.

Here is a list of all the new parts that it has over the past year.

 

Converted to deans

Gate aster

Quantum trigger

friction pro hop rubber

 

So recently I have had a new gear set put in as the stock g&g one packed it in.

 

I believe it was a 18/1 gear ratio.

 

I have had a 14/1 hi speed gear set installed. (still with stock motor).

 

It shoots 25 RPS and shoots 307 fps on .25s.

 

I will be shooting in binary and semi only and this gun sees heavy use as it is my only AEG.

 

So here is my question.

 

Should I continue to use the 11.1s or down grade to 7.4s even to the gun shoots and operates fine?

 

As I hear people saying 11.1s will damage my gun with the new 14/1 gears.

 

But I have 5x 11.1 1,100 mah batteys and it would be expensive to replace.

 

Looking forward to hearing you opinions as I wont the most life out of my gun.

 

Thanks.

 

 

 

 

 

 

 

Edited by Wegalaxy
Link to comment
Share on other sites

11.1v is going to put more strain on the gun and potentially make it break faster.

 

If you want the best trigger response: 11.1V

If you want to try to prolong the life of your RIF: 7.4V

 

You've put a fair amount of upgrades into it, and its your only RIF so I would say go for 7.4v. Or potentially buy another RIF as a backup for when you need to repair your primary.

Link to comment
Share on other sites

Last weekend I killed my Specna Edge, I'd dropped some 14:1's in as I'd calculated that with the motor I was running I would get about 24-25rps on 11.1/3s and a more realistic 18rps on 7.4/2s. 

 

Lo and behold after fitting the gears and re-shimming it came out great. 

 

I am lucky to have access to a piece of private woodland and we tend to play semi or burst, no auto allowed. I was very much enjoying my new improved RoF when in the last twenty minutes of game day I noticed it started to miss the odd BB, I changed mag thinking it might be this, then it started making a grinding sound. I stopped and switched to the communal "backup" Specna flex M4 we collectively purchased for such occasions.

 

Stripping it down at home showed that the bearings had disintegrated on the selector plate side of the box.  The bevel gear and spur had dropped and teeth were partially ground off the bevel in the couple of short trigger pulls it took for me to go "wtf is going on?" and realise I had a problem. 

 

On the day I was running a brand new 11.1/3s 2200mah turnigy nano-tech battery with a max discharge rate of 70c, so I think this may have pushed my rate of fire up a bit, as I imagine there would be very little voltage drop under load on this compared to my older butterfly/nunchuck lipos. 

 

I'll be fitting bushings, and see how that goes. 

 

 

 

PXL_20250519_201122730.jpg

Link to comment
Share on other sites

  • Moderators
51 minutes ago, Quagmire said:

Last weekend I killed my Specna Edge, I'd dropped some 14:1's in as I'd calculated that with the motor I was running I would get about 24-25rps on 11.1/3s and a more realistic 18rps on 7.4/2s. 

 

Lo and behold after fitting the gears and re-shimming it came out great. 

 

I am lucky to have access to a piece of private woodland and we tend to play semi or burst, no auto allowed. I was very much enjoying my new improved RoF when in the last twenty minutes of game day I noticed it started to miss the odd BB, I changed mag thinking it might be this, then it started making a grinding sound. I stopped and switched to the communal "backup" Specna flex M4 we collectively purchased for such occasions.

 

Stripping it down at home showed that the bearings had disintegrated on the selector plate side of the box.  The bevel gear and spur had dropped and teeth were partially ground off the bevel in the couple of short trigger pulls it took for me to go "wtf is going on?" and realise I had a problem. 

 

On the day I was running a brand new 11.1/3s 2200mah turnigy nano-tech battery with a max discharge rate of 70c, so I think this may have pushed my rate of fire up a bit, as I imagine there would be very little voltage drop under load on this compared to my older butterfly/nunchuck lipos. 

 

I'll be fitting bushings, and see how that goes. 

 

 

 

PXL_20250519_201122730.jpg

So, in essence, what your saying is......

 

You wankered it 😜

tumblr_mq6luctKP21qbo81go1_250.gif

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...