1st commando

I'll say this, get other mags . The performance on the DE mags compared to GM mags is very poor

It's about intent. The seller has to be happy that your purchase is with the intent to use it at an insured Airsoft site or organised event. Ukara just helps shops by showing what you have already done in a way to show your likely intent.

Yeah I would definitely pick up a gen 3 while you can

They will actually work out more expensive and it will still just be a TM with steel slide running on an internal hammer without any of the new design features of the GHK

neither of those brands should go anywhere near anything GBB tbh I tend to use white lithium grease from halfords for heavier applications and 4uad airsoft lubricant pens for more detailed stuff

I actually only load to either 100 or 120 as I don't think the mags will be as reliable filled to 175 given that VFC refer to them as 100 round mags with only a side note saying "they can be made to fit 175 with a mechanical loader"

I have set mine for 0.3g

WE M4 mags will work fine but it was really designed for the WE pmags

Oh cool , yeah the box mag fits perfectly . Oh I did cut a space for the pipe on the feed guides like the one on the VFC mag too but a little larger

The regular box mag one fits perfectly . Although I did remove 1" of tube to relieve some stress on the connector

I love the smoke generators combined with flash device. Here is mine currently

Shield make RS optics and for a long time supplied the british army with all it's red dot sights and BURDS. They have been around a long time , I'm not a big fan of them but they aren't dodgy

I did find that it was easy to adjust through the nozzle for a change

I did indeed and i just tapped it out and didn't see anything directional on it

Brocock were famous for the cartridge fed airgun revolvers that got banned about 25 years ago . They tried a few times to get into Airsoft but they failed to fundamentally understand it

I mean before we even go into the fact it was put in the "gas rifles" sale section I think this might be dreaming a bit for a brocock

Contact Airsoft world , it's up to them to help you. Worth emailing VFC too at [email protected] but ultimately Airsoft world should swap it right away as they are a UK retailer bound by UK trade laws.

That's been broken ! There have been a few got broken in transit etc and if you email [email protected] they will send you a new one directly. Where did you buy from?

steel barrel always wins in my book

It's important to realise something about this situation . WE AIrsoft is a page ran by WETTI/ARmed force in Hong Kong and NOT WE Model. What i suspect has actually happened is that WE Airsoft are licensed to use the WE name on gas in Hong Kong and designed the graphics etc which is why no one outside HK has seen the "original" cans. Gunfire come along to WE Model and license the WE name for Europe (they are a distributor) to make their own WE gas . However they use a graphic owned by WE Airsoft/AF rather than using their own or WE Model's not realising it's the IP of AF and not WE model . WE AIrsoft /AF then get upset and claim it as "counterfeit" I find it somewhat ironic given that WETTI has always and continues to pretend to be WE Model co on social media when they are not. Both gases are probably made at puff dino or similar who make most airsoft gases ,especially ones from Taiwan You are somewhat correct , It's the same "WE" as was involved in that drama because they were upset that WE Europe (later Nuprol) cut them out and went direct to WE Model

There should be no difference between v1 and V2 gas blocks

No worries. Interestingly it's actually a VFC stock for the AEG mk48 and I found it compatible with the buffer plate and switched them over. But thanks, I like it too

That is correct

It's exactly the same valve as every other VFC (except mp5) . I got mine from gbbparts.com Also it turns out the real B&T rail fits although it does mean you have to remove it to remove the gas tube as part of a detailed strip

I'll be fitting the CL project design adjustable valve to mine just to ensure it's always under