Cipher-032

Back when I used to have my KC02, I just ordered direct from KJW works. Yes it takes a couple of weeks but the parts did show up. I cant comment on exhaust valves as I never had one of those fail. Make sure you keep the O rings greased

What are peoples go to hop rubbers now? My modify tan is looking a little worse for wear. I can remember seeing that they have recently suffered QC issues? Im really not interested in running Maple leaf.

So to add to this issue in case anyone suffers the same: Strip and clean trigger box. Inspect your springs. I replaced ALL of mine as I had a old Dytac set for nearly 4 years. Some springs had actually compressed and failed. Relube with thin weight oil. No grease. Give a small spray of silicone oil on top once reassembled Now having zero issues with Semi auto run on. Even readjusted my adjustable trigger and sears and works lovely. Figured I put a means to an end some if someone searches for this issue.

Gunna pop in here as Ive got a bit of a issue with my MWS. Ive got the annoying issue of Semi auto "run on". Basically if I fire the gun continuously in semi, it will some times it will fire more than one shot. I did service the trigger pack with a small amount of Superlube MP grease, but Ive since learned/remembered that the MWS trigger pack doesnt like grease. So since Ive flushed it out with silicone spray as advised by Ollie Talks Airsoft. How ever he did mention about replacing the hammer? Nothing on what exactly. But sometimes as ive been testing this issue returns. Ive said bugger it, and ordered a GM Full spring set. I do have a Dytac spring set in the trigger box currently but its several years old now. I do also have a GM adjustable sear B for the trigger pull, and adjustable flat face trigger, but all grub screws are OUT so they dont do anything currently. Curious if anyone else has run into this issue, and if so share your fix? Video of the issue here: https://youtu.be/jGMGM4Z-P8o

Bolt stop issue? Using a heavier buffer will negate the performance of the high speed bolt.

If its a struggle, I do have a complete Madbull Mk18 handguard set up which I ran on my MWS for a little while All you need is either a barrel adapter or a different outer barrel, like the laylax modular one.

Ive had mine for years. It leaves a witness mark on the rubber but no cuts. For Nozzle spring strength, you only need to up is rate if you increase your ROF dramatically. I would think that makes sense. So stock to 120% should be perfectly fine

Google Super Lube Multi Purpose Synthetic Grease Grey tube, does any thing and everything and wont eat your seals. Brilliant video (And I HIGHLY recommend their other videos)

Kinda wanna keep it standard power as the optic can be on one power and act like a red dot. I do have a spare bolt, so its possible to get a spare safety and DMR it. Might think about it in the future see how I feel

My MWS Mk12 Mod H (ish) build is about 90% finished. Used a Double Bell AEG as a donor. Spent a fair bit of time working the barrel nut on and off to get it to cut on but I did it. Drilled and tapped threads to accommodate a longer bottom rail. 1-6x24 vector optics, optic. Works like a red dot on 1 power. im just gunna run this on standard power. Just polish up the stock Uber barrel again and run it on 0.32’s i love a normal kitted out mk18, but how many mk12’s do you see about?

Looks like its made for flat hop / R hop style hop rubbers. A 3d printed version of Maple Leaf's omega Nub Different nubs work best with different rubbers. The SiXG will probably always work best with your normal mound type rubbers.

Not all of them do. TM's are often optimised for 0.25's. Its kinda luck of the draw if they lift a .28g My MWS's nub was so squishy, it would hardly lift a 0.28. I had it torn down the first week I owned it to replace the nub for a solid H style one.

Ive bought a fair share of cheap sights, obviously you get what you pay for. But most of the T1's ive used Ive hit my targets. Case of making sure you set your hop then set your zero

Depends, I like T1 style or a eotech style sight. How ever im getting a LVPO for my current MWS project

Explains the resistance from the slide. Ill look into a new BBU and hammer bearing for him.

So, where do I begin? My good friend has had a WE Glock 19 back when he first started playing. Its now 5+ years old. And has a slightly neglected life. He got himself a lovely new TM P226 now as a second pistol, and I asked to take his 19 so I can service it and work out its kinks. So I gave the guns slide, and hammer assembly a full strip, clean and re lube using Super Lube Multi Purpose synthetic. The dog gonads Ive been told and it is rather good! I used a bit of silicone oil inside the nozzle for a slightly thinner lube as I found that helps bump compression. Certainly did with my SRS when I had that. I retested it and to be fair, FPS is around 240, 20FPS off my TM Glock 19 but that has a nineball 6.00 inner barrel. But my god the blow back is weak as all hell. So I tried the WE mags in the TM, and they are fine, nice and strong blow back. I tried my TM's Cow Cow hammer group in the WE. And no change, this rules out a weak hammer spring. Im starting to think nozzle / piston cup seal and maybe a stronger hammer spring? I inspected the nozzle but couldnt find anything totally obvious. Could it been a worn firing pin? But again installing my Cow Cow group didnt change much at all.

Sourced a Magpul Handguard for it at last.

Has anyone done stuff with the hop up? I know it takes AEP rubbers.

Well im hoping people would give me a sensible appraisal for it. Its hard to guage, but maybe cause of the parts, mag count etc £375? Ive seen them go for £250 with a single high cap mag or drum mag but I dont know.

Sounds like it. But I wouldnt confuse the Baton's Gen 5 with GHK's. You can see from the finish in the first post its a metal slide on the GHK.

This is for this replica: https://www.popularairsoft.com/news/baton-bg-17-co2gbb-prototype-review Not the GHK from what I can see.

2020 edition Scorpion Evo: Purchased new from Platoon Stores back in 2020 (if thats of any relevance) Wired deans from factory. 9.9 LiFE battery 7 mid cap magazines Ball bearing spring guide UK-FOB Stock adapter Zuhkov AK Stock Paske Sapper handguard Carry Case Silencer adapter Internals are not modified. Shoots perfectly fine, on all modes. Bad bits: BB strike to mock bolt. Sling adapter that sits behind the handguard is missing, but no doubt a lot of second hand Evo's are. Had to modify the outer barrel to fit the handguard, rather do that to a £60 part than a £150 handguard. Not visible and doesnt effect fitment of the stock handguard. Really not sure on what it is worth?

Where are people getting their Magpul handguards from? Seems like Pixy dust at the moment

This is normal. Every MWS does this. You can shave it down and smooth it off, but it will return. Its where the bolt hits the buffer stop

Blimey thank you. This will save a lot of agro and certainly help stop people hijacking accounts