Cyma cm.032 (M14) part identification

[Johnboy]

I'm looking for a replacement for the inner magwell as the feed tube is broken but I can't seem to find what I'm looking for, does anyone know what it's called or the part number?

[Anonymoose]

Is that not the bottom of the hop unit?

 

https://www.sixmm.com/en-gb/products/cyma-g36-hop-up-chamber-setfor-tokyo-marui-m14-aeg-series?srsltid=AfmBOoo_DgxJqB2FDvqr_tgwTo5vwLuZijEMPz8amFEh1_G2Xd_f51pm

[The_Lord_Poncho]

Looks like it to me too. Take it slow and methodical to get the M14 apart, and take an especial note of how the fake bolt mechanism comes apart/goes back together as you do it - M14s can be a bit frustrating, and to swap the Hop out, there is a fair bit of disassembly to do. Worth the effort though, just take a few photos as you take it apart as an aide memoir (assuming you haven’t done it before of course!).

[Johnboy]

No it's not the bottom of the hop unit unfortunately (would be easier to find parts) this whole section circled in red is what I need.

[The_Lord_Poncho]

Hmm - the below is the parts diagram for the equivalent TM model (which I presume the Cyma is largely/entirely based upon). It's rather difficult to fathom out - is it part M14-2 ? But - I’ve just had a look at my (assembled) CM032 - that whole part you circle is made of metal. From your original photo, it looks like the part that has snapped is plastic? If so, it is simply the feed tube that is part of the hop unit passing through a hole in that plate. It's a while since I had mine apart so i can't say for certain, but if you are able to ascertain the snapped part on yours is plastic, that’s a good clue that it is the hop unit that needs replacing only.

 

[Anonymoose]

9 minutes ago, The_Lord_Poncho said:

Hmm - the below is the parts diagram for the equivalent TM model (which I presume the Cyma is largely/entirely based upon). It's rather difficult to fathom out - is it part M14-2 ? But - I’ve just had a look at my (assembled) CM032 - that whole part you circle is made of metal. From your original photo, it looks like the part that has snapped is plastic? If so, it is simply the feed tube that is part of the hop unit passing through a hole in that plate.

 

I think you're right, it is M14-2, you can see where the little hop adjuster passes through the front.

 

But i agree it looks like the hop's broken. If the snapped part was metal it's by silver where broken, and it looks like there's a clean break seperate from the 2 horizontal ribs either side.

[Johnboy]

3 hours ago, The_Lord_Poncho said:

Hmm - the below is the parts diagram for the equivalent TM model (which I presume the Cyma is largely/entirely based upon). It's rather difficult to fathom out - is it part M14-2 ? But - I’ve just had a look at my (assembled) CM032 - that whole part you circle is made of metal. From your original photo, it looks like the part that has snapped is plastic? If so, it is simply the feed tube that is part of the hop unit passing through a hole in that plate. It's a while since I had mine apart so i can't say for certain, but if you are able to ascertain the snapped part on yours is plastic, that’s a good clue that it is the hop unit that needs replacing only.

 

Do you know a link where I can order that part?

[ButcherBill]

There's a boneyard M14 in the classifieds, might be worth making an offer to use for parts if they're compatible

 

[Daveoc33]

We've already had a short chat about that and I'm not sure we'll find a price we're both happy with. 

 

Just saw this thread now and I can see why you're not keen on buying a whole boneyard m14 for the sake of one part. 

 

This is going to sound horrible but you can use a purple plunger from a calpol tube cut to size to repair an airsoft feed tube. I've done it once on a proprietary hop unit. It wasn't pretty but it worked. The part is already broken so you've nothing to lose by trying. 

[Johnboy]

The Cyma that's broken is my backup and a friend broke it putting a mag in like a chimp on steroids ?...The G&G would have been a perfect backup if the mags weren't proprietary and £35 a pop ?, after more thought I'd have the G&P as it's more compatible with my current mags and loadout.

[Impulse]

https://locknloadairsoft.com/products/premium-full-metal-m1a-mag-well-replacement-airsoft?_pos=14&_sid=80f5d21b4&_ss=r

 

I've never bought from them and I've never heard of them so I can't vouch for them as a vendor, but... this might be the part you need. It doesn't state whether it's G&G or TM/Cyma/G&P compatible, but the high cap mags they have on their website for the m14 look like the TM/Cyma/G&P style ones (G&G m14 mags are noticeably different), so I'm going to assume that the parts they have are also TM/Cyma/G&P compatible parts

[Lozart]

On 13/05/2025 at 10:21, Impulse said:

https://locknloadairsoft.com/products/premium-full-metal-m1a-mag-well-replacement-airsoft?_pos=14&_sid=80f5d21b4&_ss=r

 

I've never bought from them and I've never heard of them so I can't vouch for them as a vendor, but... this might be the part you need. It doesn't state whether it's G&G or TM/Cyma/G&P compatible, but the high cap mags they have on their website for the m14 look like the TM/Cyma/G&P style ones (G&G m14 mags are noticeably different), so I'm going to assume that the parts they have are also TM/Cyma/G&P compatible parts

 

They don't ship to the UK - I've tried them before.

[Egon_247]

@Johnboy

 

Sorry i'm late to the party here...i have some spare Cyma m14 parts laying around, i'll have a look when i get home from work to see if i have anything. 

If its a hop unit you need, i know 6mm had them in stock as i had to get one for my boneyard special but that was late last year. 

 

Edited May 18 by Egon_247
was reading vogon poetry..

[Egon_247]

Did you find one?