Jump to content

Jefftron Leviathon and pre-engagement issues on Specna E10


Alimcd
This thread is over three months old. Please be sure that your post is appropriate as it will revive this otherwise old (and possibly forgotten) topic.

Recommended Posts

Good afternoon everyone, I’m new around here so be gentle with me.

 

I picked up a Specna E10 recently that I swore to myself I’d leave stock as a loaner gun. One thing lead to another and it ended up being little more than a metal body for the usual suspects from AK2M4 and Socomtac. 
 

I loved the idea of the Jefftron Leviathan and popped one in with a 13:1 gear set, asg M95, Infinity 35000. The power is bang on at c.340 and the ROF is great at 34rps but the issues are two fold.
 

After a few games, I’m getting error messages that state high-current and over-spin. At this point it goes into protection mode for a few minutes, I’m assuming this is temperature related. The mosfet diagnostics state that the Semi auto and motor start current are pretty high  at 80a+, I’m using an 11.1 2600 mah 30c battery in there that should be fine, right? The amperage seems surprisingly high, the shimming is fine and the bearings have been changed from the stock specna ones (they failed 1000rds in on stock internals prompting this whole build) to some Retroarms ones. Everything spins freely and the lateral play is c0.05mm on each axle. The only factor that I figure could have changed is that the specna pistol grip is the devil’s own and maybe the motor height has wandered, greatly increasing the resistance. Thing is, it SOUNDS like a well set up AEG, it doesn’t sound like it’s struggling.

 

Ive got active break turned up to full to counter the over spin, could this be a factor in it over heating? 
 

I like the Binary trigger, they do a lot of semi-only games at Finmere and Matt has ok’d binary during semi games as long as “I’m not a dick”. I don’t spam the trigger, but it’s doing a lot of rounds in semi. Again, is the relatively high draw of the motor start up my issue?

 

Next up, pre-engagement. I don’t use the full auto often, in fact on the current set up it’s set to 5 round burst on auto, but with the ROF set to anything over 26/28rps I’m getting a significant reduction in power and the resulting decrease in range is hilarious. This was my first high speed/response build and I’m clearly learning the ropes, should I be considering taking some teeth off the sector gear? 
 

I bow to your superior knowledge and experience and hope I’ve missed something really obvious. Like I said, it’s not a wanker gun and I don’t want to use it to hose people, it would be nice to get similar range when sending a burst downrange as semi shots and even nicer if the flipping thing would not decide that it needs to take 5 to chill out in the middle of a game!

Link to comment
Share on other sites

Quite a few mosfets call for no more than 20-25C rated batteries - though I couldn't see the recommended rating on the Leviathan website spec sheet. Maybe test on an 11.1v 20C and see if that clears up the heating/board errors? Maybe also test on a 7.4v and 9.6v nimh if you have any to eliminate possibility of high voltage issues.

Link to comment
Share on other sites

With an empty gearbox fit all your gears, you should be able to spin the sector gear one whole revolution if shimming is good.

Then you can rule that out for sure.

 

Active breaking will make insane heat build up, more heat in electronics means more resistance which means more current... which you've guessed means more heat!

 

That is a very fast setup you have there, personally I would swap that motor for a 22000, runs way cooler and stil see mid 20s ROF or run a 7.4V - that's the fast fixes.

I think ROF over 20-25 is pointless.

 

Pre engagement fix with your current setup will involve short stroking and a stronger spring, but this will make your 35000 work pretty hard on Semi auto.

Short stroking requires teeth removed from both the Sector and piston.

 

Learning can eat a few parts 😉

 

Always aim aim for the best mechanical setup - minimal or no active brake.

This is done using the right mix of voltage, motor, gear ratio and spring strength.

Link to comment
Share on other sites

Thanks for the help guys, I’ve got a 20c 11.1 kicking about somewhere, I might try and torture test with that and see if I can force it to over heat. That way I can eliminate the battery from being the cause of the issue.

 

Shimming-wise, with no piston/motor in the sector gear is quite happy to spin for a complete revolution if not more. That was one of the confusing elements, it didn’t sound like an AEG that was under stress once I had rebuilt it. The stock gearbox sounded awful and when opened up the motor height was way too high and the gears were SUPER tight. Worst part was that there wasn’t any lubricant and the stock ported cylinder was so roughly finished that it  had sliced the piston’s O-rings into ribbons. Not what I had expected from Specna after such polished social media content. cue Bill Murray meme
“Externals are ok though, which is nice”

 

I had some mother’s Auminium polish on my desk at the time so I polished the rails of the gearbox just to try and eliminate any potential friction. Probably overkill but I hadn’t tried a high ROF build before and was going for the “throw shit at the wall and see what sticks approach”

 

Dave, totally agree regarding ROF. My initial idea was for a demon response for semi-auto and the option of a burst mode that would put 3-5 rounds down range super quickly. I think I’ll be resolving a lot of issues if I just drop the pretty stupid notion of having a 30+ ROF and concentrate on finding why it’s overheating with semi/binary. If I can achieve 20-25 on a 7.4, it’s going to cause less stress to everything and still give me what I’m after for burst-wise

 

The more I read, the more times I see active breaking to be the cause of issues. I’ve had a Gate Nano AB fail spectacularly, scorch marks on the PCB! Thats has got to be a thermal issue too?

Link to comment
Share on other sites

  • Supporters

M95 producing 340 means great compression & bearing/spacer inside piston plus bearing spring guide

or likely a slightly stronger than labelled spring as the E10 is a titchy barrel

Seems to be like a FireHawk 140mm or something, no more than 200mm

so doubt if spring really was a m95 or 313fps rated spring in a titchy barrel

 

Probably @ 28rps you are starting to get PME where the piston & sector are starting to catch on a full stroke

which might explain qwirky results where the stroke/volume is being screwed up producing weird shots/results

- pretty lucky you haven't ripped the rack out - keep firing on full auto & something will go I'm sure

 

 @25rps you will be getting overspin & potential double firing without Active Braking

and this really is the gun talking to you & 25rps is about the limit you can push a full stroke UK 350fps gun

sure AB will prevent/reduce the overspin & double firing on semi...

BUT on 3 round burst or 5 round burst those 4 shots will be cycling close to the limit all the same

 

As others have said you need a stronger spring that will give you say 380~395 or a true m115~m120

then take off the first two or three teeth off pickup side of sector gear, the FIRST 2 or 3 teeth that engage piston

IF your last/release tooth on sector gear is same size you can leave the teeth on piston rack

it is if your last/release tooth is larger then you MUST take off the matching amount on rack

though most remove the teeth on rack just to be safe, though if the last tooth is same it clear & release OK

 

If experimenting taking off two, then three or you take too many off sector, you can just use another sector & not need a new piston/rack

As you are using a 13:1, then you need a 13:1 sector

But if you was using a 16:1 set, then very likely a reg 18:1 sector from a std set should work as ratio is down to the step/spur gear

 

Anyway - you are cycling too fast on a full stroke

 

Either set ROF on fancy mosfet to say 75%

or

Look to Short Stroke a couple of teeth with a slightly stronger spring

or

run it on 7.4v on a 40c Lipo to give you say 25rps aprox

 

VERY VERY VERY ROUGH RPS CALCULATOR....

 

MOTOR SPEED (in 1000's or K), divided by ACTUAL gear ratio, then multiply by 10 will give a ROUGH RPS on 7.4v 25c

 

EG: 35 (35,000) divided by 13.5 (probable actual ratio) = 25.6 rps

 

for 11.1v's multiply the 7.4v figure by 1.55 or 55% increase, it isn't really 50% coz gun is cycling so extra cell is a bit more boost than 50%

 

25.6rps x 1.55 = 40rps expected rps on 11.1v - especially a 30c one

 

BUT I'm only getting 34rps ???

Well it is only a ROUGH guide and the variation could be your shimming/motor angle and also some loss due to fancy mosfet

(Don't care what manufacturers say, some response is lost in those electronics over bare bone thick wire on a 3034 with no breaks/fuse etc...)

 

The ROUGH guide does work in most cases give or take a couple of rps on a UK spec gun

higher 400+ or DMR stuff will have a slightly lower rof with heavier spring blah blah blah

 

on a 30k motor:

30/13.5 = 22.2rps which many use on 7.4v

 

So as said, you should have chosen a 22k or 25k absolute max if running on 11.1v

25/13.5 = 18.5rps then on 11.1v or x1.55 = 28.7rps

 

or there abouts ffs

(stock setups on weak 18k & 18.65 will give you 9.65rps so add a bit on as it is an easy pull ratio to make 12rps)

I said it was a ROUGH calculator, easy on the motor gearing figures need a bit more added on

or insane DSG's you gotta take some off even shimming was perfect on ceramics etc....

But it does kinda give you a rough idea in a large ballpark so to speak

 

bearings/bushings actual motor performance (and they can/do vary on same motor/batches)

plus ultra thick wiring, if using lame 20c or beefy 30c+ LiPo's (some LiPo's are not same as other makes)

(Oh and don't bother expecting this to work on a stock supplied 8.4v NiMah on small Tamiya,

this rough calculator is for LiPo's on deans blah blah blah, what people should be using in their tweaked setups blah blah blah)

 

Boring anorak post nearly over.....

 

Yeah you are pushing it and that is why you are getting grief

 

Twenties is plenty on a SSG

& if you get 22~24rps, then you hardly notice it not hitting 30rps

& you can set pre-cocking for a bit better response & not need hardly any AB

 

  

46 minutes ago, Alimcd said:

If I can achieve 20-25 on a 7.4, it’s going to cause less stress to everything and still give me what I’m after for burst-wise

 

 

:)

Link to comment
Share on other sites

I’ll check that spring again. The barrel is, as you say, only about 150mm. I popped an MP5k cylinder in there so it would be appropriate for the length of the barrel and there’s a bearing at both spring guide and piston end. Compression is good with fresh O-rings on the piston head. I can’t press it in with a finger over the cylinder head.
 

I remember a slightly raised eyebrow when my chrono read 340, I think this was due to getting lower than expected results and I may have swapped the spring for something stiffer at the time To experiment. I like the ASG springs as they’re colour coded and therefore idiot-proof but I may have been a pillock and left the Specna (quoted 380) spring in instead. It would certainly explain why the motor is heating up!

 

ill double check the spring tonight and report back.
 

The fancy mosfet ROF is for whatever reason not directly proportional, ie a drop from 100-95% takes it from 34 to 28.6 so I’ll have a play around with it.

 

Thanks for the ROF prediction guide, very logical and makes perfect sense. I’ve screen shotted it to keep it to hand!

Link to comment
Share on other sites

We've all been there, more for the challenge i think than anything making ROF lasers but when you get back to the game, 20 RPS is just beautiful in an AEG, great trigger response for Semi and tight accurate burst fire.

 

Yeh I have a tricked out MP5K with 150mm barrel, awesome compression on a SS M120 = 305 FPS

 

So suspect diff spring rate or ASG springs are a little high ?? You do have double bearings though too.

 

Consider yourself educated @Sitting Duck has written... novelled 😁😘

 

I prefer 18:1, 22000 and 11.1v, so much get up and go from a standstill, quieter and motor rarely even gets luke warm!

This is pulling a full stroke MS135

 

 

IMG_4421.JPG

 

This is is a standard TM with M85 spring lol!

 

IMG_4442.JPG

Link to comment
Share on other sites

  • Supporters
42 minutes ago, Alimcd said:

I’ll check that spring again. The barrel is, as you say, only about 150mm. I popped an MP5k cylinder in there so it would be appropriate for the length of the barrel and there’s a bearing at both spring guide and piston end. Compression is good with fresh O-rings on the piston head. I can’t press it in with a finger over the cylinder head.
 

I remember a slightly raised eyebrow when my chrono read 340, I think this was due to getting lower than expected results and I may have swapped the spring for something stiffer at the time To experiment. I like the ASG springs as they’re colour coded and therefore idiot-proof but I may have been a pillock and left the Specna (quoted 380) spring in instead. It would certainly explain why the motor is heating up!

 

ill double check the spring tonight and report back.
 

The fancy mosfet ROF is for whatever reason not directly proportional, ie a drop from 100-95% takes it from 34 to 28.6 so I’ll have a play around with it.

 

Thanks for the ROF prediction guide, very logical and makes perfect sense. I’ve screen shotted it to keep it to hand!

 

"Normally" a M100 is 328fps

now when that if fitted to a 455mm AK you will get more

&

when fitted to a MP5k you get a bit less due to creep/loss

 

Also a bearing spring guide adds about 15fps due to a little more spring compression from bearings over a std plain guide

(though you loose a bit of power, volume to be exact when correct AoE so a bearing spring guide usually offsets this)

 

Cheapo China guns come with a massive heavy alloy spacer inside usually 8~9mm

as the piston's teeth is 3mm pitch that is effectively 3 more teeth of compression than no spacer

& a bearing inside piston or on piston head is about 4.5mm or another 1.5 teeth compression than bare piston

 

So with all those variables it is easy to see why a genuine M100 spring can give 300~350fps in another gun

and that is without great/piss poor seals or mis-labelled springs etc....

 

Hence people tend to stick to a particular spring make than risk playing the typical Chinese lottery on too many parts

Or, if knowing the gun shoots a smidge hot, then remove spacer(s) or Short Stroke option maybe

(or vice versa, add a small spacer to bump the fps up a bit, as long as it doesn't hit the spring guide on full retraction)

 

TBH - it don't matter what spring is in there, if you got good seals & fps is about right that is all that matters

I was just saying it sounds a bit strong for a genuine m95, that's all

 

So many many ways to skin a cat and loads of variables on these poxy toy guns

 

@Davegolf has one of them fancy hook test meters - niiiiicccceeeeeee

 

I got one of them RC testers as my test meter is ergh just a cheap test meter

 

image.jpeg.66b63ce1f5099b7756ba9c21a4b1572e.jpeg

is my actual one, but anything will do...

 

image.jpeg.f9617c7080cbad627f55c6358deda32b.jpeg

a bit cheaper, run on full auto for say 5 secs and check the amps/draw

a really efficient build and good shimming draws less amps which means less heat and longer battery

 

Motors normally draw up to 80amp on initial start up for a few nanoseconds, but soon settle down to say 15 or so

(depends on gearing & motor)

30k is about my limit to run on 7.4v & 13:1 SS 2 or 3 teeth etc... is a very good snappy base build

you can often chuck a mosfet in maybe and run a lame 13rps gun to 20rps on 11.1v if on a tight budget

 

But always worth checking the amps to see just how efficiently you built it & it's running etc...

Some fancy bastids like Titan will give you this info on screen, but a meter tells you on any gun

(plus it "can" help you find the sweet spot for motor height - in conjuction with sound it all makes)

((depending on how well you set bevel/motor height in the first place of course))

 

PS - we only know some of this knowledge or slight wisdom coz we've all made numerous

(and plenty) of balls ups, learning from our mistakes (wisdom)

Plus we are all still learning, I know I am, doing stuff slightly different to things I was doing a year or two ago

always trying to squeeze maximum performance & efficiency from each subsequent build etc...

 

I'd say you did a reasonable job compared to my first few attempts that were complete disasters

(the first three were fucked completely and the next few were far from good let alone great rebuilds)

Link to comment
Share on other sites

Haha yes I'm lucky to have one of them fancy hook test meters for work 😁

 

Yes certainly a good first ballsy build @Alimcd and you clearly have some good fortune seeing as you got away with not blitzing your piston 😂

Link to comment
Share on other sites

Thanks for all the insight, it’s great fun having a little project gun like this. When it’s purring away at 20-25rps and being electrically reliable I’ll be a particularly happy bunny.

 

I’ve ordered a 22,000 motor due to Corona cabin fever. It’ll give me a few more things to fiddle with anyway!

 

I’m hugely appreciative for the help and look forwards to many more fuck ups going forwards. Here’s a little piccy on the Specna anyway, it’s basically a pistol. I can feel the more Milsim inclined already adding me to an ignore list!

DBD7E122-8610-488B-B950-2C0E9C93D005.jpeg

Link to comment
Share on other sites

But at least you have an L85 above it, not another AR... yawn 😂

 

Although yours is hot little guns like that are ace indoors, def have a soft spot for SMGs 😁

 

IMG_4476.JPG

Link to comment
Share on other sites

The L85 is the “just leave it alone gun” so if the others that I’ve buggered around with fail, I’ve still got a stock ICS that’s perfectly fine. All it’s had is a gate NanoHard popped in to save the contacts! I thought it would be ironic to have an L85 as my Ol’reliable

 

Loving that MP5K!

Link to comment
Share on other sites

The ICS L85 is a great gun, nice gearbox too. I've had 3, only have my first one left, but it's in bits lol as it became a self contained HPA project 🙈

I did not leave it alone 😂

 

Going back to a previous comment of yours - I agree cabin fever is 'spendy' lol, just ordered a load of guts to pimp yet another gearbox, just can't leave it alone!

 

I imagine @Sitting Duck crafting away at something as we speak haha!

Link to comment
Share on other sites

HPA looks pretty interesting, I think I’ll just get my head around AEGs for now! 
 

Looking forwards to trying that 22,000 it could be the solution to both the PME and the overheating. Thanks for the advice guys

Link to comment
Share on other sites

  • Supporters
1 hour ago, Alimcd said:

HPA looks pretty interesting, I think I’ll just get my head around AEGs for now! 
 

Looking forwards to trying that 22,000 it could be the solution to both the PME and the overheating. Thanks for the advice guys

 

TBH - just try a decent 7.4v....

 

22,000 x 1.55 = 34,100

 

your present motor is a 35k supposedly on 8.4v (7.4v fully charged, each 3.7 cell can hold up to 0.5 extra volts = 4.2v)

so a 7.4v = 8.4v fully charged or a 11.1v = 12.6v

 

the 1.55 or 55% value for 2 cell > 3 cell calculation so speed rps will be running nigh on the same

 

YES the AMPS from the 22k will be lower but due to Voltage the Watts will vary....

 

eg: 35k draws say 19 amps on 7.4v so a full Lipo = 19 x 8.4v = 159.6 Watts or say 160 Watts

 

now 22k on same 13:1 say 12.5 amps (guessing tbh), 12.5 x 12.6 = 157.5 Watts - not a lot of difference eh ???

 

I based this guess on similar builds & @Davegolf 10.4a on a m135

though I feel you must have a m110 at least & your gear ratio of 13(13.5) over a 18(18.65) is about 1.38

So basing on a smidge lower of 10a x 1.38 = 1.38 possible reading, maybe round it down a bit

(I've had a really low 25k ferrite 13:1 SS 3 teeth build draw 11.75 @ 335fps)

So did a kinda guess in the middle of a neodym 22k being around 12.5-ish

could be 12amps, doubt if it would be 13amps but your shimming might be a whisper smidge out so 12.5a is my figure

 

12.5a x 12.6v is not far off the Wattage of say a 19a x 8.4v - though this could be 20a x 8.4v = 168 Watts but not THAT much difference

 

Don't matter, but might save you £40

 

Just saying you might be OK just on 7.4v and perhaps a higher capacity as you should gain some space on a 2 cell than a 3 cell LiPo

 

FFS, this Corona Isolation bollox better end soon if the highlight of my day is doing mathematical airsoft predictions :P

My calculations could be completely way way off the mark and is intended to only be guide, it does not reflect the true actual readings you may or may not get as each gun is individually different plus....

 

Your gun is at risk if you do not keep up servicing or other loans secured upon on it

charges & indemnities may apply & you should always seek professional advice

any advice given is regulated by the amount of alcohol I have consumed

Sitting Duck is not affiliated with any other species of water foul or any other poultry or KFC

 

Full T&C's available on request - if I can be arsed depending how long this corona or thread goes on for

Link to comment
Share on other sites

  • Supporters
6 minutes ago, Davegolf said:

Remember maths is fun kids 👀

 

I have asked somebody to give them the once over to see if they are about right

 

Unfortunately she is self isolating with Corona 25 as she is high risk & has type 3.5 diabetes....

 

The Philosophical Muser: 08/03/17

Link to comment
Share on other sites

With all the measures taken by treasury, we’ll need her unique mathematical mind as chancellor by the end of this!

 

 

Also, SittingDuck. I haven’t completely ignored your advice. I’m going to try a 7.4 in there as well first.

 

I’m working from home and had eBay open in another window. Got a proper ball-achey task come in and thought, sod it, why SHOULDN’T I have a 22,000 as well. Complete the set...

Link to comment
Share on other sites

  • Supporters
38 minutes ago, Alimcd said:

sod it, why SHOULDN’T I have a 22,000 as well. Complete the set...

 

Yeah, I got like that with loads of things like consoles, peew peew's etc...

doesn't hurt to have a spare "just in case...."

 

Now I finally admit I have a problem....

I have no more fucking room to hide them from Mrs Duck

 

agreed - your money - your gun/motor & all that

Me personally I'd use a 22k/22tpa mainly for higher stress build say a DMR or DSG perhaps on 11.1v

For reg AEG I tend to go with 7.4v on a balanced 30k/16tpa

Others might use a Higher Speed 40k+ on std gears to achieve the snap, but that can draw more amps

(though if you don't spam loads a higher speed motor is OK, just going nutz will create more heat)

 

It is all down to personal preference, budget & your circumstances

Admit I was using faster motors at first, but found they (the motor) or they gun didn't last too long

Now I tend to stick on a 25k to 30k, but no faster for me on 7.4v

 

I stick on 7.4v coz it is generally cheaper and space saving over a 11.1v

(not always true, HobbyKing do some deals at times where a 25c 11.1v block LiPo is cheaper than similar 7.4v)

https://hobbyking.com/en_us/rhino-2200mah-3s-25c-lipo-pack-w-xt60.html?queryID=7bd535558be7b9d8aedbbec64c6dc4eb&objectID=83948&indexName=hbk_live_magento_en_us_products

Link to comment
Share on other sites

I must confess that the quality of Lipos is something I have less than zero knowledge about. I just used the same company that I used to buy Nimhs off back in the day, componentshop. 
 

I’ve been using these

https://www.componentshop.co.uk/11-1v-2600mah-25c-continuous-discharge-cranestock-lipo-battery.html
 

and have just noticed that they aren’t 30c as thought but 25c. Are these infamously crap or worth sticking with?

Link to comment
Share on other sites

  • Supporters

Vapex are a trusted name in airsoft batteries

 

Airsoft batteries are funny batch of juice boxes, often so called "airsoft" Lipo's do not match up to the same RC LiPo's of same spec

 

If you read reviews on HobbyKing, they have said the Turnigy "Nano-Tech" LiPo's designed for airsoft fall short of a block Turnigy of same rating

Be it less than expected performance - a 25c not having the same oomph as similar 25c

or the 2000mah Nano-Tech not lasting no way as long as a 2000mah block Lipo

 

Now Airsoft guns vary loads and crane stocks you often need ergh crane Lipo's like Nano-Tech & Vapex offer

The option for cranes is to wire in smaller block LiPo's in PARALLEL to create the SAME VOLTAGE but DOUBLE the capacity/mah

 

Wining diagram for Lipo's in series & Parallel | Model Flying

 

Don't do series or those 2 x 7.4v's will make a 14.8v and that would be REALLY taking the piss

Of course you don't have to wire two LiPo's in series in a crane stock

You could fit 2 x 1300 Lipo's, one in each tube and just go with one 1300 connected at a time

if you get caught short in battle then you switch over as soon as possible without going back to safe zone

(and both batteries don't have to same make/type/spec if only using one at a time

if pairing up LiPo's in parallel then they should be same types etc....)

 

On other guns like a G36 or an AK with a fixed stock you chuck in block type batteries which are MUCH cheaper than the "airsoft" crane lipo's

of run a fixed stock - a fixed stubby stock on titchy M4's and chuck any bloody battery shape in there

 

As yours is a titchy FireHawk type M4 these stubby stocks really work great with the gun tucked in tight to you for CQB I found

Or classic M4 a full size fixed stock option, though you lose the fine tuning of comfort to your own bespoke play style on full size fixed stocks

 

As always there is often a trade off in what stock and if wired front/back for weight balance or if to use a peq box etc....

 

Buying "airsoft" batteries will always be more expensive than block type

Also there are the 9.9v LiFe batteries that offer a stop gap or bridge between the 7.4v & 11.1v

Me personally I found them not to offer any really extra zest over a decent 25c or 30c 7.4v in a tweaked gun

But others say LiFe's are awesome - though my gut feel is that they might be OK in a stock/moderate tweaked gun

but in a gun that is tweaked a bit more the LiFe's that I tried really didn't seem to offer the boost I was expecting

so therefore though a potential stop gap between the two LiPo's I personally they don't have the real brute grunt of a LiPo in a 13:1 SS build

(I could have duff Turnigy LiFe's but when I tried them I just didn't feel it)

 

The cheapo 11.1v is what I'd buy to chuck in a cheapo Cyma 28a keeping most of it stock

end up getting towards near 20rps for next to fuck all, don't think it would fit in a G36c

so would have to measure and weigh up a smaller 11.1v for std build

or look at 7.4v 13:1 etc..... to get near 20rps maybe on better motor

Actually getting ultra involved, a JG is a 22tpa so rip that motor out of a G36c

replace it with a 25~30k neodym in G36, then drop the JG 22tpa in 28a AK & run on 11.v

(cheap Cyma motors are slow 28tpa so the JG 22tpa would offer a welcome bit of zest for a budget tweak)

ahem..... just saying various options of shifting stuff and matching up bits as stuff is a bit thin on ground atm

 

Airsoft batteries will cost more - even from HobbyKing and a bit more from "Airsoft" shops - they gotta apply their mark up

Places like HobbyKing you are going to one of the largest retailers of batteries for all hobbies and so you will save money

though you need to know and measure your potential battery space, checking very closely what you are buying

plus drop the dimensions a bit to be on safe side AND allow a bit more for both power & balance leads when you try to fit it in ya gun

 

Hence fixed stubby or guns that take a block type battery is perhaps easier to measure and choose something that will give good performance and capacity - but I've still screwed up buying a battery that didn't fit as expected in the past (oooops)

Also many HobbyKing LiPo's will come with XT60 over deans or small tamiya

so really this battery malarky is for people who know or not afraid to cut (one wire at a time ffs) &fit their own deans

 

Component Shop will offer you the service of Small Tamiya/Deans/XT60 on most of their batteries

all as part of their service, though no such thing as a free lunch or deans

 

For your battery £23 on deans plus £4:99 APC delivery = £27:99

on ebay seems like £28:65 so not cheaper this time around...

https://www.ebay.co.uk/itm/11-1V-800-2600mAh-Airsoft-LiPO-Battery-All-Sizes-Custom-Connector-/121637306533?var=&hash=item6297d00f3b

 

Component shop is very very respected on here, great customer service and ship stuff with low cost shipping, even on small orders

Also check out them on ebay, like many sellers, at times their ebay listings with free shipping included can end up being a tiny bit cheaper

Many sellers don't update or calculate complete costings when they apply increases or something

well it don't hurt to look, not always the case but at times sellers ebay listings can work out cheaper

 

It is all crap you learn through experience or rather as your toy gun collection grows and your wallet dwindles

Link to comment
Share on other sites

Thanks, I’ll absorb the information and when the LiPo eventually fails I’ll see if I can replace with one of your recommendations.
 

I picked up one of the ASG Strike stocks recently and there’s room in there for a decent sized brick style battery. I haven’t offered up one of my 7.4 2200 blocks as I got so wrapped up in the “must have 11.1 for the rate of fire because YouTube told me so”

Link to comment
Share on other sites

  • Supporters

Ahhhh Youtube - which isn't THAT bad if you watch respected chaps

(remember opinions are like arseholes - everybody has one etc...)

 

the real risk is watching really old clips where stuff is really out of date

Or taking say the US techs as gospel - ergh they got 400fps + limits

so their PME won't kick in until say 30rps due to faster return of m120 spring

where as UK 350fps means 25rps is about your limit - so you can't take everything you see as 101% gospel

or old methods/tweaks of yester-year and the fanboys now matured into the not so fan-men (hopefully)

(go on I'll admit to buying madbull/prowin/modify/ultimate and any other go faster add-on's that this tech raved about)

 

I admit the stuff I do today is a bit different to how I did stuff 5 or 6 years ago when i starting teching ergh breaking guns

so as said it is a constant learning curve that we are all still learning as we go, learning from each build almost

 

  

19 minutes ago, Alimcd said:

Thanks, I’ll absorb the information and when the LiPo eventually fails I’ll see if I can replace with one of your recommendations.
 

I picked up one of the ASG Strike stocks recently and there’s room in there for a decent sized brick style battery. I haven’t offered up one of my 7.4 2200 blocks as I got so wrapped up in the “must have 11.1 for the rate of fire because YouTube told me so”

 

I wouldn't worry too much, my normal War & Peace essay bollox

Just pointing out in my own very "concise" way there are numerous ways to achieve similar results

eg: 7.4v on zesty 30k motor or 11.1v on more torquey 22tpa motor - it's 350fps so either will do

as long you don't go mental on 45k if you can help it if planning a rebuild is my own personal choice

(but to each their own as stated many many times)

Link to comment
Share on other sites

  • 4 weeks later...

For anyone interested in an update, Sitting Duck's advice sorted the pre-engagement issue and the formula for calculating ROF has been pretty spot on. 6 weeks of not being able to do much has led to an acute case of madness and poor financial restraint. I won't tell you what's new in the gearbox yet, I'll try to get a few pictures when I can get in and do the work but it should be a bit of naughtiness! The Specna body is currently with Mark at FMJUK for a bout of Cerakoting as the Specna finish was crap. It's coming back with a Graphite Black and Satin Aluminium paint job so purists, avert thine eyes.

 

Last few parts needed for the build arrived at my workplace today so as soon as I can get in to start putting it all together, I'll get some pictures up on here.

Link to comment
Share on other sites

  • 4 weeks later...

It’s amazing how little you can get done during lockdown when you’re about 13 miles away from your workbench! This has taken 3 sneaky Monday morning UPS-drop off runs to finish but it was worth every excuse I had to tell my wife!

 

just waiting on a new ejection port cover from PowAir and she’s done! Internally, it’s now Sporting a retro arms split V2, 16:1/SHS DSG with a M160 spring giving about 340 (+-5) at c.40rps. Drum mag feeds like a champ and the new externals scream “wannabe youtuber who claims everyone is a cheater”

 

The C-More sights are great BTW and I think it’s a nice break from the sea of Eotechs and Aimpoints seen on every other pew. 


cheers again to Sitting Duck for the advice!

 

EC324155-0654-4C46-85A5-13A14163F89D.jpeg

697E2B2E-7C21-4D59-B201-E651FB0D6006.jpeg

E007BBC8-B10C-4EFD-8513-8D17BC1E9CAF.jpeg

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...