sonofsammo Posted November 5, 2019 Share Posted November 5, 2019 Have come across a bit of a problem with my MWS when I'm running my HPA drum mag. It's running at just under 50psi, at under the DMR limit of 298 fps on .36s. BUT it's utter wank. No range at all. Really slow bolt and poor recoil. No shot to shot consistency in range or accuracy. It's operating probably 50-60% of the range I get from using mags / red gas. Here's a link to some vids:https://photos.app.goo.gl/dhjNR55tJjKenKtR6 The vid of the lower fps is from the drum mag, whilst the higher is red gas mag (the mags were warm when I did the test, hence the higher fps). The other vids are so you can hear/see the difference in the bolt/recoil... Can anyone give me a clue as to wtf might be going on? Because I have not got the foggiest! Link to comment Share on other sites More sharing options...
Guest Posted November 5, 2019 Share Posted November 5, 2019 I say send it back to the drum maker and get a full refund 😂😂 Link to comment Share on other sites More sharing options...
sjhirst Posted November 6, 2019 Share Posted November 6, 2019 I'm probably asking the obvious, but does it perform better with higher psi? I had a we scar that if the psi was too low, the recoil was sloppy and range was bad as there was not enough air to cycle correctly. Link to comment Share on other sites More sharing options...
sonofsammo Posted November 7, 2019 Author Share Posted November 7, 2019 On 06/11/2019 at 08:14, sjhirst said: I'm probably asking the obvious, but does it perform better with higher psi? I had a we scar that if the psi was too low, the recoil was sloppy and range was bad as there was not enough air to cycle correctly. Yup, works much better with higher psi- but power goes up and is no longer site legal 😞 I think it might be the reg, so @rocketdogbert had kindly lent me his to see if it works any better. Link to comment Share on other sites More sharing options...
Guest Posted November 7, 2019 Share Posted November 7, 2019 18 minutes ago, sonofsammo said: Yup, works much better with higher psi- but power goes up and is no longer site legal 😞 I think it might be the reg, so @rocketdogbert had kindly lent me his to see if it works any better. Fingers crossed mate 🙂 Link to comment Share on other sites More sharing options...
sjhirst Posted November 7, 2019 Share Posted November 7, 2019 yes, hope its that and it gets sorted Link to comment Share on other sites More sharing options...
Skara Posted November 29, 2019 Share Posted November 29, 2019 I reckon you could use a shorter barrel, in relation to the PSI needed to let the gun fully cycle. Let's say you have a 400mm barrel (just guessing, I have no idea what lenght you're running), you switch to a 300mm one and up the PSI to idk, 70 to get the same J output. As you all know barrel lenght has no impact on accuracy/consistency. It's just another way to regulate FPS/m/s/J output. As an alternative you could run a larger diametre barrel, from idk, 6.04 to 6.23, with the same end result (cranking up the PSI without impacting the J output) Link to comment Share on other sites More sharing options...
jsmithski Posted January 5, 2020 Share Posted January 5, 2020 Obviously no gbbr works at 50psi unless highly modified. I normally run all my hpa gbbrs at 120+ psi which in turn requires some mods to be at a desired FPS. Link to comment Share on other sites More sharing options...
Boristhedriver Posted February 7, 2020 Share Posted February 7, 2020 Just out of interest where did you get your MWS drum mag from? Link to comment Share on other sites More sharing options...
sonofsammo Posted February 7, 2020 Author Share Posted February 7, 2020 30 minutes ago, Boristhedriver said: Just out of interest where did you get your MWS drum mag from? It was custom built for me by our very own legend @rocketdogbert 😄 Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.