Supporters sp00n Posted November 7, 2015 Supporters Posted November 7, 2015 Here is my review on the Alyan Arisoft and Reaper Airsoft GBBR m4 hi-cap mags. For the purpose of this review i am using my bog standard (no npas) WE SCAR rifle. why HPA mags?, i really don't like real caps, gas can get expensive, gas mags are not cheap, winter, and i already have HPA gear. (both mags are sold as 1000rd mags, but the Alyan is 1inch shorter so i suspect its only a 800rd mag) Alyan Airsoft mag This was the first out of the 2 mags i bought. from the outside this mag looks really nice, however its not very good at all. My first problem was i could not get bb's to feed, they kept getting stuck in the alloy top part, i found there was a small tube inside the head, 5mins with some emery paper soon sorted that, then on to testing. I could not get the FPS above 265fps (0.25's) and the FPS would vary wildly from shot to shot, i went as far as getting a palmers regulator and taking the air pressure up to 180PSI, with out joy. at this point i decided to open up the mag and see what was what. Just behind the fitting that screws into the alloy block, was clogged with PTFE tape, and this lead to another discovery ... the valve that Alyan use's is ... well rubbish. It is not one that's designed for gas, its backwards (literally), and you are relying on the spring that goes to the brass striker on the back to keep it closed! (unlike most valves that the gas pressure aids in keeping the valve closed, this one the gas fights against the spring). No matter what i did, i cannot get this mag to work. Its pants don't, buy one you will waste 120 Euro's Reaper Airsoft After being burned by Alyan, i noticed that a lot of people who ran GBBR's, used standard WE mags but with the russian HPA tap. This is where Reaper Airsoft comes In! They don't try to reinvent the wheel (valve arrangement) they do it right, basically they use the top end of a standard WE GBBR mag mated to the hi cap mag, and it works brilliantly, proper British engineering!. with approx 65PSI i was getting 300FPS (0.25's). They where brilliant when i was asking about the mag, and sent me loads of pics that i asked for. Now don't get me wrong, it is £140, but it works! and for me its worth every penny. also major plus points go to this mag, as should the gas valve fail, being standard WE item, its easily replaced Conclusion :- Alyan Airsoft= useless waste of time and money if they was on fire and i had a glass of water .. i would suddenly be very hydrated Reaper Airsoft = extremely well made mag, that dose exactly what it is supposed to do i would buy from them again. proffrink and spiralvirus 2
Supporters Rock-climby-Dave Posted November 7, 2015 Supporters Posted November 7, 2015 What is the BB capacity on the mags? spiralvirus 1
Supporters sp00n Posted November 8, 2015 Author Supporters Posted November 8, 2015 Doh, sorry i forgot to add that lol they are both sold as 1000rd, but the reaper is approx 1inch longer, so i suspect the alyan is only a 800rds spiralvirus 1
spiralvirus Posted November 8, 2015 Posted November 8, 2015 Ive got a few Reaper mags and have bought from Allyan in the past. Allyan uses 800 round mags where Reaper use 1200, that's what they start off as anyway, by the time they've been adapted your going to lose a few rounds, which is how Reaper come up with 1000, I Think Allyan just plucked a number out of the air though to be honest, sp00n 1
Supporters sp00n Posted November 8, 2015 Author Supporters Posted November 8, 2015 Are these electric hi-caps? yes they both are
Recommended Posts