Wild Weasel

Guns great I think it may be the operator!

So what is the solution? Fill as best as you can, and just swap out for another mag if it gases out mid game? That will get annoying with only 5 mags. It's a cracking sustem, well built, very accurate and great when it's going right but I'm struggling to make it useable - I just cannot seem to be able to gas the mags up enough for reasonable usage even after green gas modding them!

Nope struggling to get a full mag out of any of the five, I don't know if it's my filling adapter or the fill valves. All mags hold gas and are on calor's finest. I wonder if a complete strip and rebuild would do it? I just can't understand how people can get a full mag out of a ten second squirt. I did not have this problem with my Kwa MP9!

Thanks, I'll try that.

No, as God intended.

Ladies and gents, if I was still in a class I get the feeling I'd be wearing the dunce cap. I'm still struggling to fill my mags reliably from propane - They are all basically new, have been looked after, have been green gas modded, have two different types of propane adapter on the bottles (the madbull type, the Airsoft innovations polymer type and a brand new v5 blue AI adapter type from firesupport. I have replaced two of the fill valves with laylax nineballs and yet I'm struggling to fill some of them. The symptoms are as follows: starts to fill for a second then goes quiet, so I take the nozzle off, give it a shake and go again. Nothing no gas/liquid transfer - nothing, so only after pressing way harder than I should it starts to fill a bit which gets me a few more rounds then gasses out again. After a couple of times of this I can get it to fill using the madbull type nozzle as the ai nozzle vents the can if you press too hard. I know this has been done to death on this forum but I'm really struggling and would appreciate the advice. I don't think I should need to stab the crap out of the fill nozzles but find it the only way to get gas in so I must be doing something wrong. Like it said all my mags are looked after and never left un gassed... Help!

I've still modded all mine as I was none the wiser, I reckon it still ok to do and gives you a slightly bigger gas capacity!

Yep spot on, cheers.

Yep, fail, when I push the ai polymer fill valve on, the mag fill valve does not want to 'give' and if I push harder the ai bottle adapter vents instead. All other 4 mws mags and 3 hk45 mags ok. The spring feels very stiff on the mag valve like!

Just done it now, left it in a pot of 5cwt silicone oil for ten minutes and reassembled. Looks brand new in there too me!

Thanks Dave, I'll have a look at stripping it today as I couldn't get gas in - it felt like there was no spring back. Other news my flame king refillable 1Ib bottle kit arrived today so those of you who run propane that is an option as Coleman bottles and I believe plumbers bottles are not refillable due to a bearing being added to prevent that. I now have 19kg of gas for plinking! Cheers

Sorry if this has already been asked (can only find one fleeting reference) but has anybody tried these : https://eagle6.co.uk/shop/catalog/product/view/id/575/s/laylax-nineball-magazine-gas-injection-valve-set-black-for-all-gas-series/ had my first failed inlet valve on my first mag plinking today! Cheers

I fitted a rs BCM gunfighter trigger guard to mine, I had to do a small amount of filling on the trigger guard at the front on top to get the small hex screw hole to line up, also the drift pin that came with it is too large diameter so be nice to your existing mws one to re use. Make sure you support the "wings" when you tap this through or you risk breaking them off!

So, looks like it's going to be an omega nub then. So, I'll just give that a go and let you guys know how it turns out, just in case somebody else buys one then. Cheers lads

Hi, I'm getting a bit concerned about the reliability of my Angry gun MPA nozzle I've noticed my FPS consistently dropping and after adjusting it the screw is very loose that adjusts the nozzle. Has anybody tried putting a spot of weak loctite on the screw after removing it or is it not recommended - I'm running Coleman propane on a standard gun. Can anybody advise who has one of these nozzles. Cheers

Hey, does anyone know the contact for the six g supernub on here, I've been after one for a bit but I've had no reply. Cheers

ATRG has a review https://atrg.blog/2019/12/14/accessory-review-hao-mk16-rail-part-one-13-5-urg-i/

Nice one thanks.

Yep +1 on this, I'm still a Mws noob and I was wondering the same - I'm basically stock less an angry gun MPA nozzle running on Coleman propane shooting 340fps on a new mag with 0.3 BLS precision bb's ending up around 30fps lower at shot 35. Is this normal and if so how can you get consistently and accuracy with such wide variables? Cheers

Update, been using this for a bit now with Coleman propane, lags out everywhere like bit does the job..

Hi, I know this has been covered again and again but I can't seem to find it - I currently have a stock cqbr mws and would like the mk18 Daniel defence rail look, however some people are telling me it will drop straight on others are saying it will require a bit of machining where the handguard strikes the front receiver pin holding the upper and lowers together. Could someone recommend a handguard, barrel nut, barrel wrench, gas block and anything I'll need to square this away please. Additionally would anyone have any experience of this:- http://www.redwolfairsoft.com/redwolf/airsoft/Accessories_RIS_Systems_G_P_DD_MK18_M4A1_RIS_II_9_5_inch_Front_Set_for_Tokyo_Marui_M4A1_MWS_GBBR_Black.h Cheers

Bollox, I was after 3 next week - he did mention he was ordering in 70 odd by mid Dec though so all good.

Where do I find NugentGL, had a shufti at you/face tube and drew a blank.

Yep, +1 on that. I wonder how many TM's have been sold on the back of those videos??? Two from me for definite.