Jump to content
SSPKali

We G19 Recommend Upgrades

Recommended Posts

I am loving my WE G19 with the Maple Leaf hop unit and crazy jet barrel.

 

The trigger safety has got a bit floppy so I was looking at replacing that with a Guarder unit...is there anything else I should look at replacing while I have it in pieces?!

 

Looking for consistency and efficiency...not bothered about cosmetics.

 

TIA!

Share this post


Link to post
Share on other sites

Do you mean the front bar that locks the trigger?

 

If you disassemble the front rail (which you’ll need to do to replace the safety spring anyway), you can just bend it back.

 

To improve accuracy, try the non-drop g17 barrel mod, and /or inner barrel stabilisation (plenty of info on YouTube) 

Share this post


Link to post
Share on other sites
1 minute ago, rocketdogbert said:

Do you mean the front bar that locks the trigger?

 

If you disassemble the front rail (which you’ll need to do to replace the safety spring anyway), you can just bend it back.

 

To improve accuracy, try the non-drop g17 barrel mod, and /or inner barrel stabilisation (plenty of info on YouTube) 

Hi, no the little lever that sits in the trigger blade, the spring tension is pretty poor in it.

 

I'll take a look at those other mods, thanks!

Share this post


Link to post
Share on other sites
Just now, SSPKali said:

Hi, no the little lever that sits in the trigger blade, the spring tension is pretty poor in it.

 

I'll take a look at those other mods, thanks!


that’s because it’s a cheapo little bit of plastic, unless you have the WET edition, got a picture?

Share this post


Link to post
Share on other sites
Just now, rocketdogbert said:


that’s because it’s a cheapo little bit of plastic, unless you have the WET edition, got a picture?

Just the regular one, which is why the Guarder trigger would be a good upgrade

Share this post


Link to post
Share on other sites
Just now, SSPKali said:

Just the regular one, which is why the Guarder trigger would be a good upgrade


personally, I’d go for an SAI trigger, but the rigged Guarder is fine. I’ve probably got a few spare standard triggers floating about

Share this post


Link to post
Share on other sites

9ball mag routes are good . There's also the lees precision route shims always fitted them both in all my gbbp mags. The lpe shims are not fitted for the glock but you can snip one end off and place 2 or 3 opposing and will do the same job. The shim improves the seal between the route and bbu piston. The route improves the flow of the gas. Will boost 10-15fps and fps consistency  without any negative effect.

 

Share this post


Link to post
Share on other sites

Temp improvement with slivers of 3M sticky pad adding some spring to the naf bit of plastic. Now resetting the trigger safety.

 

I have also eliminated much of the inner / outer barrel wobble and hop unit to frame wobble.

 

Happily knocking toilet roll centres over at 12m with little fuss. Roll is about the size of the front sight at that range.

 

Thanks for the pointers!

20200419_153758.jpg

20200419_154842.jpg

Share this post


Link to post
Share on other sites

Personally I really like the WET trigger. You should be able to get one easily from KY Airsoft.

Share this post


Link to post
Share on other sites

I fitted the Laylax / 9ball purple gas routers to my mags today (great service by Fire Support as usual)

 

G19 is shooting well but fails to lock the slide back at all. I am guessing this is due to the new rubbers and extra friction and should settle down?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...