GiantKiwi

https://www.youtube.com/watch?v=JnzCJfyrnu4 Video, still processing.

Nope.

Used a Reprap (Cost about £250-£300 to make) to make a part to replace the weakened original, which is load bearing, for an Ergotron MX Monitor Arm, It currently has £3500 worth of monitor on it (all 13kg's of it), I have absolute faith that the one above would be more than sufficient for a go pro (<1kg?)

I'm just glad I bought loads with my LM4, so i'll never have to deal with the hassle of finding them. Now just to scrape up enough funds for an MKM

Why be concerned? Your friend obviously didn't do much research, as if they are so dangerous, why would every modern portable electrical device be using them?

So my internet is being slow. It's barely made it halfway through the upload

It has to be a lipo, as you will see in the video when it finally uploads. On a side note, didn't notice this until after i'd done the video: I do believe this might have one of the toptech gearboxes in it o.O

Youtube, file is 2.5GB...this may take a while.

I've done the video now, just need to upload it, i'll just upload the raw footage for now, just to give an idea of it. There are a few things that need removing from it for the long run

Well its not a high cycle, according to G&G those are being recalled as they have very low fps and chew themselves to bits rather promptly.

Whoever told you Flash Mags reduce the noise is talking utter rubbish, if anything they're worse. If you buy Lonex (or ASG rebranded) they will give about 2 years service until the ratchet spring fails. But then a replacement spring is a few pence to replace. If you however buy the cheap ones, you'll get a few months tops before the whole mechanism collapses, which is virtually irreparable. Had a few of each for a Dytac for woodland games, the Lonex were drastically better.

More marketing BS from G&G. It needs a stock tube LiPo, not exactly difficult to get hold of, a smart charger such as a Imax B6 or a Turnigy Accucell 6 is needed however. The cheap power brick ones are no good. No G&G gun as far as I am aware comes with a battery or charger. And I've had a lot of them in the past 5 years. Those midcap mags are what i've bought to go along with it, so I shall be able to give a fair assessment of those as well.

Nope, nope, nope. 5.56 suppressor on a 7.62. ACOG is way too high to maintain cheek weld whilst shooting. And that rail? Just no.

Not going to lie, but I didn't buy it for the supposed high cycle, that's just a possible bonus. I wanted that amplifier

Well after ringing them to find out where the hell it is, been informed it will be shipped today, so arriving tomorrow. Will try to get a short video up on it promptly afterwards.

high cycle is just a high rate of fire, from the videos of them introducing it at SS 2014, they were aiming for 40rps.

I ordered one on Monday, waiting for the damn thing to be shipped. I'll be reviewing it as soon as it does arrive however, as there are reports of this supposedly being one of the new G&G high cycles (please god, be true ) Oh and FPS isn't everything, the G&G hop unit is good enough that the difference in range between 328 and 350fps is pointlessly minimal.

http://www.youtube.com/watch?v=TfMc0dRBc20 And a complete opposite,

Condor OD M14 Double Stack pouch and Box of KA M14 Midcaps (Feed lip now fixed)

It already has a 6.04 as standard, but I want an Orga Magnus 6.13 or 6.23, and everything else will be replaced with lonex v7 parts bar the gearset. Sorbo'd, AOE sorted, Airlab Mosfet. When I bought it, it was on the understanding that i would be keeping only the gearbox shell and the externals in the long run. Replacing the hop rubber is a given, and will undoubtedly be a prommy purple. Aiming for ~400fps semi locked. The sling: http://www.military1st.co.uk/54001-019-5.11-single-point-static-sling-black.html

Got it originally to go with the recoil 416 (no one had any freedom art sling points in stock), it comes from a 5.11 Static Single Point sling kit, and it is by far one of the best made I've used. Once i'd dialed the hop in, the rifle was insane, only guns outranging me on the field were a fully Laylaxed VSR and L96, still going to upgrade the internals anyway

Would just like to say Pete's packaging when shipping stuff is absolutely top notch, definitely worth considering for parts

CYMA M14 MOD 1 EBR. Bought this nearly a month ago now, been throwing stuff at it for the external look and have now got it to a point where I am happy with it. Internally, I'm not touching it, because it was surprisingly accurate at range when I was testing it before purchase. Getting skirmished for the first time tomorrow, then 2 weeks time it's coming to Northern Star with me