[THE TM MWS thread]

Does anyone know whether the MWS take down pins are milspec or not? Looking to get rid of the slop between the upper and lower that's built up over the past year, but don't know if 'oversized' take down pins will fit or not. 

[THE TM MWS thread]

7 hours ago, RMDavis said:

Anyone running an Angry Gun complete high speed bolt carrier with MPA nozzle?

 

With lower ambient temperatures fast approaching I was wondering whether a lighter bolt carrier would help me with my intention of using my MWS in every season!

 

Or is my money better spent elsewhere?

 

Any help/advice would be appreciated. 👍

I've ran mine for about 3000 rounds now and just had my first problem with it. The top portion where the gas key would be on an actual AR snapped clean in half whilst firing, causing no additional damage luckily. AG told me that this is a common fault with older batches, but they've resolved it now by changing the material. 

Only advice would be to keep AG and TM parts separate, some of the springs are different lengths and the fitment of things isn't very good between the two.

[THE TM MWS thread]

So, I just took apart my MWS hop adjuster unit again because it wasn't holding its position properly, and I've stupidly pinged the dial clicker across the garden. Does anyone have a spare one for sale? Eagle 6 are currently out of stock. 

EDIT

Just found it it a plant pot luckily, still need to know why it won't hold position though if anyone can help 

[THE TM MWS thread]

12 minutes ago, SSPKali said:

Probably due to play and uneven / offset spring tension causing binding. It is a really weird trigger set up that has lots of places for friction and uneven loading

 

My fix for this was to strip and clean the trigger parts, note where they were burnished and sand them with fine grit wet&dry then rebuild with 0.1mm shims to remove as much play as possible while not causing it to bind. Takes a while to do but much smoother and consistent now.

 

One thing to check is that you are not getting a light strike...The valve knocker isn't moving with the first stage?

Cheers for the reply, no the knocker doesn't protrude until the second "wall" and everything seems to work fine, honestly would be fine with it staying either single-stage or two-stage, the randomness is the annoying part. Bought the dynamic precision enhanced trigger box springs as spares for when something breaks - thinking now might be the time to try them if I'm taking the unit apart.

[THE TM MWS thread]

[THE TM MWS thread]

Sorry if it's been troubleshot before but has anyone had their MWS trigger turn two-stage? It doesn't happen every time, but after the initial take up, if the trigger isn't pulled straight to the rear it almost slips a centimeter or two before reaching another wall. It doesn't happen consistently which is the main problem, as sometimes the trigger breaks normally and sometimes I get the false break and new wall which throws me off. Seems like a weak spring or a bad contact patch between something in the trigger box, any help would be appreciated before I open it up, cheers.

EDIT

Added a video to better demonstrate the problem; the first trigger pull is normal, then the second one I thought was going to be two-stage but almost slipped through with the full trigger pull, and the third stuck very firmly on the second stage.

[THE TM MWS thread]

1 hour ago, Horse84 said:

Yea just last week. Take out your BCG and press on the hop up unit assembly with your finger if u feel any bit of movement, it has come loose. You’ll have to disassemble the barrel and tighten the retaining screw holding the hop up assembly in place. After you’ve done that there should be no more movement in the hop assembly and that should be you sorted 

Ahh my bad, thanks for the answer though 👌

[THE TM MWS thread]

Sorry if this has already been written about and I've just missed it but has anybody has their hopup wheel come unset when shooting? Currently mine undoes almost one click per shot, meaning my hop can go from fully engaged to fully off in less than a magazine. Anyone had this happen or know of a fix?

[THE TM MWS thread]

Anyone else taken the dive with spray paint yet?

[THE TM MWS thread]

26 minutes ago, Cyberlawyer said:

I have a stand alone Mk18 barrel currently fitted to my MWS and I also have the original short CQBR barrel.

 

Other than a difference in how the barrel nut fits (to hold the free footing rail on the MK18) I can’t tell any meaningful difference in the length.

 

A different flash hider would make more difference.

The shoulder of my outer barrel ends further back than the gas block on mine, I can't even put a flash hider on the end of the barrel in conjunction with with my gas block. The previous owner said he'd installed the angry gun 'milspec'outer barrel however I was sceptical as it didn't come with any of the additional barrel extension lengths.

[THE TM MWS thread]

6 minutes ago, Jacket said:

 What outer barrel do you currently have? If it’s the standard TM one on a CQBR, then that is 10.5"

It's a standard 14.5", decided to just get the angry gun 'milspec' outer barrel kit tho - not sure my original idea would've worked anyway as the threads run long 

[THE TM MWS thread]

Does anyone have/know where I can get a MK18 barrel extension for the 10" MWS outer barrel? Just wanting the small extension part, not looking for an entire outer barrel set. 

Alternatively, I believe any 0.5" outer barrel extension will work

[THE TM MWS thread]

Hey everyone, I've got some IronAirsoft Pmags which won't fill (I know there's better magazines, but I got them in a deal and up until now they've been alright - better in colder weather than stock mags IMHO. 😬) Problem seems to be the flow valve, which simply ejects all the gas out as I fill the magazine. I shot them until empty once, left them for a couple of hours at most and now they won't hold any gas. Checked all the O rings and added some PTFE tape in moderation to the threads just to be sure. The problem however seems to be the gap around the rear plunger and not the O ringed section that screws into the magazine. If anyone's had something similar or has some advice it'd be much appreciated - cheers