All Activity
- Past hour
-
Time Left: 6 days and 23 hours
- Wanted
- Used or as new
Looking for a few pieces, if you have any or multiple of the below I’ll gladly take them off your hands! after the following: Magpul RVG Grip Magpul BAD Lever Magpul/ Ergo etc rail panel any brand: Car15/ L119 stock pad Tangodown stubby grip HRF RCM / RAM magwell Surefire suppressor + 3 or 4 prong device RS Desert eagle grips (hogue etc) trademarked m203 (any size/ mount) please PM if willing to sell Thanks!NO VALUE SPECIFIED
-
Time Left: 6 days and 23 hours
- For sale
- Used
I bought this gun as a CQB gun in case I ever need one and I never did! So this gun just sits in the box not being used! This gun has had: new gears (standard ratio) replaced the trigger unit for the 2020 revisioned version which works so much better suppressor adaptor it shoots lovely on 0.8J with 0.28’s! looking for £350 with the 6 mags (there’s 5 in the photo but I need to find the 6th)£350
- GB
-
I don’t remember what mine cost; it was nine years ago.
-
Time Left: 6 days and 23 hours
- For sale or swap
- As new
LNIB only test fired Upgrades BAV TAC titanium z plate Bav tac 140% nozzle spring Bav barrel nut tool Bav tac BavTacs Magic Hop Nub Maple leaf steel crazy jet inner barrel Flamingo hop rubber Like new without a mark on the exterior. collection from Leicester trades or PX possible for other GBBR. WhatsApp 07393187136£320
Leicester - GB
- Today
-
Galvatron reacted to a post in a topic: Macks airsoft dreamers of the week thread
-
Austeyr reacted to a post in a topic: Macks airsoft dreamers of the week thread
-
That's a damning sentence right there
-
Galvatron reacted to a post in a topic: What grinds your gears on forums
-
Bracie5150 left Positive feedback for LukeTunst
-
I paid £550 for mine 😉 It was 8 years ago but still 😂
-
You've done a good job on the lower fence, I was gunna do that myself on a couple of builds in the past but never plucked up the courage. On another note, the later versions of the XM177E1 had a full fence lower receiver. There countless pictures showing this, and it would have still matched with the M16A1 traded lower which had it as standard. Unless you plan on filling these in also, like you did the selector markings on the opposite side? Nice work though.
-
Mine cost £580.
-
https://prefired.co.uk/ads/ares-l1a1-slr-aeg £650 for a preowned, or £610 for one with warranty (Which you'll need with it being Arse, I mean ares) https://www.defconairsoft.co.uk/product/ares-l1a1-slr-aeg-black-ar-024-p Even Daves Custom Airsoft is cheaper! https://www.davescustomairsoft.co.uk/ares-l1a1-slr-aeg-polymer
-
andrey reacted to an advert: A&K VN M60
-
Colin Allen reacted to a post in a topic: LCT G3 DMR upgrade, V2 gearbox swap
-
Well done to them; locking out via an ETU or mosfet should be acceptable. I know that the argument against is "But you can reprogramme it." However, how many sites actually check that DMRs really are mechanically locked?
-
Jackioannou737 left Positive feedback for DeadByDawn
-
Time Left: 6 days and 21 hours
- For sale
- Used
PPS K98k for sale. Shot about 30 times. And decided that albeit it's a lovely piece for a collection. It's not for me when it comes to actually playing. Comes with 5 mags, 1 of them as seen in a plastic wrapping, does need a new o ring where you fill with gas. The other are gas tight. Comes with a sling but it is for a gewehr 98 so it doesn't technically fit but does the job. Any questions lemme know!£400
Cheddleton, Staffordshire - GB
-
-
AcseticGumby joined the community
-
Socks reacted to an advert: GHK DDM4 14.5 V3 tan cerekote
-
ButcherBill reacted to a post in a topic: The 'What have you just bought' Thread
-
JRT joined the community
-
Tommo92 reacted to an advert: Metal & Wood Trenchgun
-
The 'What have you just bought' Thread
GiantKiwi replied to Cameron364's topic in Guns, Gear & Loadouts
Because everyone on HRC raves about them, I have bought: Waldo Dynamics MWS Hop adjuster arm and a pack of the Ion MWS return springs. Omega nub was a reasonable stop gap, but it doesn't work briliiantly, and the stock DE return springs are just poo. -
-
Socks reacted to a question on an advert: 50RD gas magazine for m4
-
-
KeyboardWarrior joined the community
-
-
Yeah same, the price is ridiculous. Mine has been great so far though.
-
Sorry, I missed that.
-
-
I was about to suggest a SADF M83 chest rig but then I googled them and saw how much they go for these days. If I'd known when I got mine they would up to quadruple in price I would've got more than 1
-
Orange_06 joined the community
-
Can LCT or other Brand V3 gearbox fit with NPO VSS-M
Austeyr replied to TsLo's topic in Electric Guns
A standard V3 AK gearbox should drop straight into it however I believe the motor cage may be proprietary to the NPO for how the stock is mounted. You will lose the selector ability (Should retain safety as it's physical?) -
sibur left Positive feedback for fredhill19
-
-
Or they give it a theme and name it then paint the hardcase in the theme,have gaudy quotes all over it and an insane price tag. (Looking at you "joker" themed aap)
-
I have a question about my NPO VSS-M because it's an HPA airsoft for now. I want to rebuild it back to an AEG. Wondering whether it can fit with a normal V3 gearbox, btw I don't mind about losing its special selector function because I have to install a ETU inside. I know the NPO one has different measurements with LCT. If you have the same airsoft as me, please leave your comment.
-