Motor only works when I hit it

[Hangtight]

Depends on the battery....but I keep coming back to the ASG 30k for most builds too, although the 22k on 11.1v and 13:1 gears with a 9 tooth bevel is nice for rapid semi auto with heavier springs.

[ImTriggerHappy]

1 minute ago, Hangtight said:

Depends on the battery....but I keep coming back to the ASG 30k for most builds too, although the 22k on 11.1v and 13:1 gears with a 9 tooth bevel is nice for rapid semi auto with heavier springs.

Op is claiming 110 with an 11.1v lipo so should be good. 

 

22k is good for Dmr builds 

[SCAR_Jester]

20 minutes ago, ImTriggerHappy said:

Op is claiming 110 with an 11.1v lipo so should be good. 

 

22k is good for Dmr builds 

Sitting Duck is helping me out with a spare 28TPA, which is overkill for a cqb semi auto on SSG but it means I don't need to pick up a mosfet with Active Braking (yet). Or worry about any sort of heat issues.

Run that till it dies then grab a mosfet with AB or a TITAN + a slightly less torquey motor.

 

[ImTriggerHappy]

53 minutes ago, Corky2110 said:

Sitting Duck is helping me out with a spare 28TPA, which is overkill for a cqb semi auto on SSG but it means I don't need to pick up a mosfet with Active Braking (yet). Or worry about any sort of heat issues.

Run that till it dies then grab a mosfet with AB or a TITAN + a slightly less torquey motor.

 

Good old Duck the man is a star.

[Sitting Duck]

2 hours ago, Corky2110 said:

Sitting Duck is helping me out with a spare 28TPA, which is overkill for a cqb semi auto on SSG but it means I don't need to pick up a mosfet with Active Braking (yet). Or worry about any sort of heat issues.

Run that till it dies then grab a mosfet with AB or a TITAN + a slightly less torquey motor.

 

 

2 x Cyma armatures (right side with white gluey bit by commutator end)

both with D pinions, seem OK, sit at 90 degrees with a JG bevel

so "should" sit at 90 degrees with a SHS bevel & others

Cyma bevels are cut funny sitting at 85 degrees so not all teeth mesh 101% in situ

(think I found a few odd qwirky pinions that sit with cyma bevels better for next cheapo build)

 

Anyway.....

 

 

2 x Cyma's on right side with OK pinions (D type)

one pinion is a bitch to get on the other Cyma/Chaoli

but other pinion fits on all 3 armatures

 

1 Chaoli on left from f*ck knows where....

(but some people crave/rave about them)

28tpa for me on 7.4v is a bit slow - fine for 3 cell mofo's

 

Fairly sure they are 3 x similar looking 28tpa mofo's

 

Was gonna send an end bell (tee hee bell end) from each type

so you got some spare brushes or stuff

but might as well send up 2 motors complete & spare armature and be done with it

The long shaft guides are just crap solid scrap alloy

 

I'll chuck it in a small box and send it out tomorrow I guess

Hopefully you should be able to get a new lease of life in your gun once again

[SCAR_Jester]

9 minutes ago, Sitting Duck said:

 

2 x Cyma armatures (right side with white gluey bit by commutator end)

both with D pinions, seem OK, sit at 90 degrees with a JG bevel

so "should" sit at 90 degrees with a SHS bevel & others

Cyma bevels are cut funny sitting at 85 degrees so not all teeth mesh 101% in situ

(think I found a few odd qwirky pinions that sit with cyma bevels better for next cheapo build)

 

Anyway.....

 

 

2 x Cyma's on right side with OK pinions (D type)

one pinion is a bitch to get on the other Cyma/Chaoli

but other pinion fits on all 3 armatures

 

1 Chaoli on left from f*ck knows where....

(but some people crave/rave about them)

28tpa for me on 7.4v is a bit slow - fine for 3 cell mofo's

 

Fairly sure they are 3 x similar looking 28tpa mofo's

 

Was gonna send a end bell (tee hee bell end) from each type

so you got some spare brushes or stuff

but might as well send up 2 motors complete & spare armature and be done with it

The long shaft guides are just crap solid scrap alloy

 

I'll chuck it in a small box and send it out tomorrow I guess

Hopefully you should be able to get a new lease of life in your gun once again

Have my babies..

 

But in all seriousness thank you for your help, really.

PM me your invoice