Jump to content

Archived

This topic is now archived and is closed to further replies.

DazMK5

Where can I buy PDI and Laylax parts for a Tokyo marui VSR?

This thread is over three months old. Please be sure that your post is appropriate as it will revive this otherwise old (and probably forgotten) topic.

Recommended Posts

Interested in getting a VSR-10, just want o see where I can get few bits from for it.

 

Cheers

Daz.

Share this post


Link to post
Share on other sites

Google search for 'pdi x fire it should take you to pdi's own website. Its an Asian shop but good prices

Lay lax can be bought from a number if retailers, try fire support.

Share this post


Link to post
Share on other sites

What's better PDI or laylax?

Share this post


Link to post
Share on other sites

And you can't get PDI hop up units from there :( or spring guide

Share this post


Link to post
Share on other sites

You don't need a new hop unit. Get a full cylinder set, it'll have all you need in that area.

PDI are generally rated better than lay lax.

Share this post


Link to post
Share on other sites

So if I just get a full cylinder set, new spring, new barrel and PDI zero one trigger, will that be everything I need for it to reach 500fps and be deadly accurate with good range?

 

M_P Your a legend mate :)! Always out to help others, cheers mate :)

Share this post


Link to post
Share on other sites

Will I need a hop lever or hop up chamber? Or change hop up itself for accuracy? Ill be shooting .3g bbs :) cheers mate

Share this post


Link to post
Share on other sites

Pretty much- make sure it's a standard one though, not a 'bore-up' one as they're made for different dimension receivers or something.

Yeah get the one on aspuk, the A type or whatever it was called (completely forgotten the brand) but no need to replace any other hop component.

Share this post


Link to post
Share on other sites

100%?? Thanks a lot mate, I thought. Wold need the hop up chamber for accuracy lol :).

 

So Ill get these

 

- (VSR310) http://www.x-fire.org/etop/bolt_sp.html

- (VSR10 pro 430mm 0.1 tight bore) http://www.x-fire.org/etop/01.html

- (this cylinder set???) http://www.x-fire.org/vsr10/e.vsr_cylinder_vc_pal.html

- (trigger??) http://www.x-fire.org/vsr10/e.vsr_triggerset.html

- (hop lever A)

http://www.airsoftsniperparts.com/apps/webstore/products/show/3072283

 

With this, I will get my good FPS and consistent accuracy?

(What are steel pins for)

 

That's me done then if that's it, but I might need someone to double check, ;). Cheers pal x

Share this post


Link to post
Share on other sites

Looks about right to me- you'd get a better air seal (and so consistancy and therefore accuracy) by getting some ptfe tape around the hop rubber and barrel and cylinder head threads. Then you just need to make some barrel spacers from electrical tape and you'll be sorted.

I'm doing the exact same with my VSR as soon as I get the money to do so as well lol

It's probably a given but you'll be wanting to be using .36g minimum bbs, probably .4s to be honest/

Share this post


Link to post
Share on other sites

Ah ok, so ill need the hop lever B instead then ;)

Share this post


Link to post
Share on other sites

Official Distributor - came across it last night while looking for something else.

Share this post


Link to post
Share on other sites

Official Distributor - came across it last night while looking for something else.

Cheers mate, nice to know you was thinking of me ;) lol

Share this post


Link to post
Share on other sites

×
×
  • Create New...