SimonDJXC Posted July 6 Share Posted July 6 Hi, I am running 0/28s and was wandering if anyone knows what spring would get me to about 300fps. I am currently at 250. Any recomendations? Link to comment Share on other sites More sharing options...
Colin Allen Posted July 6 Share Posted July 6 There are so many variables that it is almost impossible to say. What spring is currently fitted? Link to comment Share on other sites More sharing options...
SimonDJXC Posted July 6 Author Share Posted July 6 i believe it was called an M something.... looking i think its the m100. next question is then will the mofset need upgrading as well? Link to comment Share on other sites More sharing options...
Hudson Posted July 6 Share Posted July 6 You don't want to beat 300 on 0.28s. The 1.14J limit will be approximately 295fps. Rather than opening the gearbox and swapping the spring, you'll probably be better off ensuring you have a good air seal, as well as bucking & barrel which should get you to what you want. Cannonfodder 1 Link to comment Share on other sites More sharing options...
SimonDJXC Posted July 6 Author Share Posted July 6 how do you ensure a good seal? Link to comment Share on other sites More sharing options...
Hudson Posted July 6 Share Posted July 6 Good bucking and barrel and ensuring it's all in place properly and snugly in the hop unit to start with, after that it means opening the gearbox up and getting good air nozzle/cylinder etc. parts Link to comment Share on other sites More sharing options...
Colin Allen Posted July 6 Share Posted July 6 (edited) 3 hours ago, SimonDJXC said: i believe it was called an M something.... looking i think its the m100. next question is then will the mofset need upgrading as well? You need to get it up to about 280-290 fps (300 is hot!), which is a considerable increase and, if the current spring is an M100, is going to need at least an M110 spring. However, assuming that the barrel and cylinder are properly matched, you may well have a poor air seal, which you would be well advised to sort out. Give the inner barrel a good clean with isopropyl alcohol as well. You don’t need to upgrade the mosfet just because you install a stronger spring. Edited July 6 by Colin Allen Link to comment Share on other sites More sharing options...
Galvatron Posted July 6 Share Posted July 6 1 hour ago, SimonDJXC said: next question is then will the mofset need upgrading as well? What feature do you think your current one is lacking that you need to upgrade it? Link to comment Share on other sites More sharing options...
SimonDJXC Posted July 6 Author Share Posted July 6 i dont, just watching dissasembly videos doesnt seem to hard. I will try .25s first. can you identify which barrel and cylinder we are talking about? definatly something i want to check. Link to comment Share on other sites More sharing options...
Galvatron Posted July 6 Share Posted July 6 For the sake of clarity, can you confirm which gun you are talking about? Are you talking about the TM 416 DEVGRU NGRS or another RIF that has DEVGRU in its name? One troubleshooting tip is checking the compression in your cylinder - if you put your thumb over the nozzle while pressing the piston into the cylinder, a sign of good compression is that you will eventually get resistance against pushing the piston. If you get no resistance and you piston goes all the way down despite your thumb being in place over the nozzle, you've likely got a compromised seal, which would explain why your muzzle energy is much lower than expected with an M100 spring. Your piston head and/or its O-rings may be the culprit is your compression is poor. Colin Allen 1 Link to comment Share on other sites More sharing options...
Colin Allen Posted July 6 Share Posted July 6 21 minutes ago, Galvatron said: For the sake of clarity, can you confirm which gun you are talking about? Are you talking about the TM 416 DEVGRU NGRS or another RIF that has DEVGRU in its name? One troubleshooting tip is checking the compression in your cylinder - if you put your thumb over the nozzle while pressing the piston into the cylinder, a sign of good compression is that you will eventually get resistance against pushing the piston. If you get no resistance and you piston goes all the way down despite your thumb being in place over the nozzle, you've likely got a compromised seal, which would explain why your muzzle energy is much lower than expected with an M100 spring. Your piston head and/or its O-rings may be the culprit is your compression is poor. And/or the cylinder head O ring(s) and the seal of the nozzle to the air tube. Galvatron 1 Link to comment Share on other sites More sharing options...
SimonDJXC Posted July 7 Author Share Posted July 7 Yes TM 416 Devgru. Ok thanks will give that a try! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now