Pollynator_bravo2 Posted November 20 Share Posted November 20 Evening all, so I have put together a quick build with some bits I had in the garage. I brought a max pro hop as the spare I had was bust. It’s running a max 21.25mm nozzle, maple leaf bucking. Compression from cylinder was fantastic no leaks. Inside the gb is a 13:1 gear set with a ASG 18k motor. I had two inner barrels that I’ve tried a brass 280mm and a steel 240mm I think. I am getting on the brass a range between 160 -280 and on the steel it never got past 150. 🤦♂️ there is no delay chip on as there wasn’t in this gb before. any ideas ? Link to comment Share on other sites More sharing options...
Pollynator_bravo2 Posted November 20 Author Share Posted November 20 FYI was testing with 0.28g bbs. I grabbed a hi cap mag to test but normally I run mid cap pts epm1 mags so not sure if it’s a feed issue? Link to comment Share on other sites More sharing options...
ak2m4 Posted November 20 Share Posted November 20 What's the cylinder type, and what's the spring if you happen to know? Link to comment Share on other sites More sharing options...
The_Lord_Poncho Posted November 20 Share Posted November 20 With that much fps variation, potentially the bucking is folding at the lips? If you haven't already, maybe try a variety of different buckings, and ideally a different hop chamber at least to rule that out. Link to comment Share on other sites More sharing options...
Pollynator_bravo2 Posted November 21 Author Share Posted November 21 9 hours ago, ak2m4 said: What's the cylinder type, and what's the spring if you happen to know? Spring I think in m100. Cylinder I can’t remember the exact type but the port looks to be about two thirds down the cylinder 7 hours ago, The_Lord_Poncho said: With that much fps variation, potentially the bucking is folding at the lips? If you haven't already, maybe try a variety of different buckings, and ideally a different hop chamber at least to rule that out. Ok cool I have a couple of stock buckings I can try. Maple leaf have given me the occasional issue in the past however this one looked to be positioned correctly compared to those that have given me grief Link to comment Share on other sites More sharing options...
ak2m4 Posted November 21 Share Posted November 21 cylinder vents sounds right, as other said chop and change the chamber and/or the nozzle Link to comment Share on other sites More sharing options...
Colin Allen Posted November 21 Share Posted November 21 I would start by swapping out the hop unit or pairing it with a Maxx nozzle; the Maxx hop units are very picky and can be prone to power fluctuations if they are not happy. Link to comment Share on other sites More sharing options...
Pollynator_bravo2 Posted November 22 Author Share Posted November 22 On 21/11/2024 at 21:58, Colin Allen said: I would start by swapping out the hop unit or pairing it with a Maxx nozzle; the Maxx hop units are very picky and can be prone to power fluctuations if they are not happy. Yeah it’s paired up with a Maxx nozzle as I had also read this so was a bit miffed when I ended up With problems tbh Link to comment Share on other sites More sharing options...
Colin Allen Posted November 22 Share Posted November 22 1 hour ago, Pollynator_bravo2 said: Yeah it’s paired up with a Maxx nozzle as I had also read this so was a bit miffed when I ended up With problems tbh I would still try changing both the hop unit and the nozzle. ak2m4 1 Link to comment Share on other sites More sharing options...
Pollynator_bravo2 Posted Tuesday at 21:01 Author Share Posted Tuesday at 21:01 So tried changing bucking and it got worse, tried different barrel still bad. Checked compression on nozzle (should have done this before) and Maxx pro noz was leaking loads. Tried another max pro noz and same thing. Switched back to shs and hey presto it worked a treat. Now consistent fps at 270/280 and 0.9j-1j on 0.28g. Happy days and thanks for the help folks The_Lord_Poncho and Colin Allen 2 Link to comment Share on other sites More sharing options...
Colin Allen Posted Tuesday at 21:10 Share Posted Tuesday at 21:10 8 minutes ago, Pollynator_bravo2 said: So tried changing bucking and it got worse, tried different barrel still bad. Checked compression on nozzle (should have done this before) and Maxx pro noz was leaking loads. Tried another max pro noz and same thing. Switched back to shs and hey presto it worked a treat. Now consistent fps at 270/280 and 0.9j-1j on 0.28g. Happy days and thanks for the help folks Excellent! That is a success. Pollynator_bravo2 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now