Alexharris246 Posted July 5, 2019 Share Posted July 5, 2019 Hello all! I've been having a few issues with my tm glock. First of all the slide kept getting stuck half way so i researched the issue and everyone was saying its the trigger bar so i replaced the trigger bar. However this has not fixed the issue and when reassembling the small spring in the hammer assembly (Pictures for reference) shot out and flew across the room and out the window. The glock still fires however the slide does not slide far enough back to pick up the next bb. Could the spring that shot out be linked to this or is it another issue? Cheers, Alex. Link to comment Share on other sites More sharing options...
Guest Posted July 5, 2019 Share Posted July 5, 2019 It’s not that little spring. Without it, your gun won’t fire properly, but it’s unlikely that’s the issue. Does it still have the same fault as previously? Where are you in the country? Link to comment Share on other sites More sharing options...
Alexharris246 Posted July 5, 2019 Author Share Posted July 5, 2019 2 minutes ago, rocketdogbert said: It’s not that little spring. Without it, your gun won’t fire properly, but it’s unlikely that’s the issue. Does it still have the same fault as previously? Where are you in the country? It does have the same fault as previous but it doesn't happen as frequent. I can rack the slide a few times before the issue occurs whereas before it happened after the slide was pulled back once and i am located in Lincolnshire. Link to comment Share on other sites More sharing options...
Guest Posted July 5, 2019 Share Posted July 5, 2019 https://www.fire-support.co.uk/product/guarder-enhanced-spring-set-for-maruikjwe-glk-g17g18c Very tricky to fix remotely, how much wear on the gun? Replace the spring, and try again Link to comment Share on other sites More sharing options...
AK47frizzle Posted July 5, 2019 Share Posted July 5, 2019 How was it getting stuck halfway? Could yyou force it forward? If so, it's probably just the roller on the trigger unit. Needs a good clean with the contact points. Link to comment Share on other sites More sharing options...
Alexharris246 Posted July 5, 2019 Author Share Posted July 5, 2019 3 minutes ago, rocketdogbert said: https://www.fire-support.co.uk/product/guarder-enhanced-spring-set-for-maruikjwe-glk-g17g18c Very tricky to fix remotely, how much wear on the gun? Replace the spring, and try again I think i might send it off and see if anyone else can fix it as taking them apart stresses me out as all the parts are so small and i have big hands 😂. Could you recommend anyone? 1 minute ago, AK47frizzle said: How was it getting stuck halfway? Could yoy force it forward? If so, it's probably just the roller on the trigger unit. Needs a good clean with the contact points. The slide couldn't be forced forward, i had to remove the mag and get the slide off by pulling the slide back and use force to get the slide off sideways. Link to comment Share on other sites More sharing options...
Guest Posted July 5, 2019 Share Posted July 5, 2019 12 minutes ago, Alexharris246 said: I think i might send it off and see if anyone else can fix it as taking them apart stresses me out as all the parts are so small and i have big hands 😂. Could you recommend anyone? I can sort it, or @AK47frizzle Link to comment Share on other sites More sharing options...
Alexharris246 Posted July 5, 2019 Author Share Posted July 5, 2019 2 minutes ago, rocketdogbert said: I can sort it, or @AK47frizzle How much? Link to comment Share on other sites More sharing options...
AK47frizzle Posted July 5, 2019 Share Posted July 5, 2019 24 minutes ago, Alexharris246 said: How much? I'd suggest feeding the poor, hungry student I got parts lying around to fix it immediately I'll dm you. Link to comment Share on other sites More sharing options...
Guest Posted July 6, 2019 Share Posted July 6, 2019 This ^^^ Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.