• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

THE TM MWS thread

Wavey_Gravey said:
Get a new grip, one with a steeper drop off.
Click to expand...


This helps (love my bcm gunfighter) but also make sure your stock is extended the correct amount for you, when holding so the stock tube parallel to your forearm, the stock end should sit neatly in the elbow crease. 

So many people have the stock too short, especially for airsoft (no recoil to manage). 

 
Any budget friendly place to buy TM mags?
aftermarkets ones are extremely expensive when you buy 3+ price is almost double.

 
StoveCap said:
Newish here too, had my DE MWS a few months now. So take what i say with a little salt, but from my experience and research -

Firstly, the Bolt needs to be forward, and the gun has to be primed. Just rack the gun, and punch out the pins.

Secondly, especially with green gas, you need to swap the nozzle return spring. Bavtac make the best out there afaik.

Thirdly, Its a whole lot of maths and physics, but Gas guns are prone to this thing called Joule creep - far more than their AEG or spring counterparts. Without going to jargon, you'll notice that heavier BBs have proportionally more power than they would with AEGs. To remedy this you'll want to get this thing called an NPAS. The best one out there is the Federal Concepts NPAS/ FEDA valve (However they're out of stock right now, as he's swapping to a newer version, shouldn't be too long until they're back in stock), followed by the RA-Tech, then the Angry gun. 

Sub-Note, using weaker gas is actually what the TM system is made for, green gas is stronger than what the system is designed for, so using duster gas (otherwise known as 144a) is also a perfectly alright alternative to installing an NPAS.

Lastly, after every game day. Especially if its outside, and especially with green gas. Explosive enterprises made a good video on how to maintain your gun, but its mainly - wipe the barrel, wipe the BCG, wipe the visible parts of the lower and all of the inside of the upper, apply lube where needed, and go.
Click to expand...
Thank you very much for all of the replies just quoting one as I didn’t want to fill the feed, great information from everyone! 
 

I found some Abbey 144a gas but it’s got ‘maintenance’ gas written on the from will this work or no good? 
 

Thank you again! 
 

 
Hound said:
Thank you very much for all of the replies just quoting one as I didn’t want to fill the feed, great information from everyone! 
 

I found some Abbey 144a gas but it’s got ‘maintenance’ gas written on the from will this work or no good? 
 

Thank you again! 
 
Click to expand...


It has a higher Silicone content so not optimal to use.  The Silicone ends up on the hop rubber and negates the back spin. 

 
Yeah, don't run maintenance gas through your gun. It's great for storing your mags after a game day as the higher silicone content keeps the o-rings nice and lubed, but vent it out and refill with regular gas before shooting because as @Chev Chelios said, the higher silicone content will get on the hop rubber and stop it from shooting well.

 
Ulmocuk said:
any thoughts about these mags?
https://www.sixmm.com/en-gb/products/cgs-cyma-30-rds-stanag-magazine-for-cgs-marui-mws-m4-gbb-series?pr_prod_strat=e5_desc&pr_rec_id=51656ba78&pr_rec_pid=8168672854273&pr_ref_pid=8162908274945&pr_seq=uniform
Click to expand...
Thats a CGS (Cyma Gas System) which is just T8 Shit renamed. It wont work with your MWS (not well atleast). Avoid any and everything T8 / CGS.

Its stupid that they're still trying to market T8 stuff as MWS compatible. 

 
I wouldn’t be putting any kind of mineral oil near an airsoft gun personally.

 
StoveCap said:
Thats a CGS (Cyma Gas System) which is just T8 Shit renamed. It wont work with your MWS (not well atleast). Avoid any and everything T8 / CGS.

Its stupid that they're still trying to market T8 stuff as MWS compatible. 
Click to expand...
Thanks mate appreciated ? 

 
Today, I finally found the time to install my Flamingo 60 bucking, Titan nub, and Crazjet inner barrel (250mm) into my N4 Noveske. However, I was disappointed with the results I got. When I tested my upgraded N4, the range and accuracy were almost the same as when it was stock. I couldn't think of anything I might have done wrong. Have any of you encountered this problem before? Any advice would be greatly appreciated.

Note: I was using the mag EMG Helios Noveske N4 M4 MWS Gen 3 Gas Magazine by Double Eagle ( Hate these mags but it is only available atm)
With nurpol green gas and 0.32 BB

 
Last edited by a moderator:
Have you changed the gas routers in the DE mags? The stock ones are not a great seal. Try the GM ones.

I've picked up the GM v3.5 nozzle as pictured, does anyone know what the rubber o ring is for and where it goes?

View attachment 129341

 
You must log in or register to reply here.

Similar threads

Rechard
Which M4 gas mag is better? VFC or MWS?
Replies
6
Views
1K
ProfHappyCat
ProfHappyCat
Angelvill3
Guns modify mws magazine issue
Replies
2
Views
714
Angelvill3
Angelvill3
Cr0-Magnon
MWS GBBR for Plinking?
Replies
5
Views
631
BigStew
B
aragoth
Custom m733 MWS
Replies
3
Views
358
ButcherBill
ButcherBill
Impulse
G&G m700 knock arm and plunger set issues
Replies
6
Views
1K
Impulse
Impulse
Back
Top