cropzy

http://homepage.ntlworld.com/phopewell/airsoft/chargetimes/ From what it's calculated it will take 9 hours and 54 minutes.

What does your charger output in milliamps?

What type are your batteries. What voltage are they? How many milliamps are they?

I actually really like it. I really like stuff like this too.

I see you have a point, however I want full face protection without having to wear goggles and mesh separate.

Just use this http://www.amazon.co.uk/Paintball-Goggle-Proto-Switch-EL/dp/B0020R399A/ref=sr_1_1?ie=UTF8&qid=1399452868&sr=8-1&keywords=proto+switch+el I do an I have not looked back.

ARES UMP 45 Mid cap (finally found a place that stocks them!)

Baka.

Practically every tactical torch. Be a little more specific.

It was literally what I had lying around in the garage. I do plan on getting some krylon and painting the whole thing then putting some military stencils on. Thanks for the nice feedback!

Cropzy here again. Here is how I made my gun case. I purchased one of these of off Fleabay http://www.ebay.co.uk/itm/271152550770?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 Now they are old and have been stored outside since the 90's so they have a little rust on them. The case itself is quite heavy being an army surplus ammo crate. They are air tight and water tight and the locks are very tough and hard to lock. Mine came with the original inserts for the munitions it once held, which are certainly bigger than 50 cal. I took the lid and give it a scrub down with a wire brush to get rid of all of the loose rust and then did the same to the case itself. I then took the lid and painted it with some green Hammerite we had laying around, this is so that the lid is protected from rust and rain etc for the future. After it had dried. I then started looking at foam to put in it, I figured most gun cases have egg box style foam in so I bought a sheet of it measuring 2m L x 2m W x 3mm H and cut it to size in 3 pieces. 1 for the bottom and lengthways sides. Then the other 2 for the other sides. I then purchased some spray glue (carpet adhesive) and sprayed the inside and fitted the foam and then let it dry. The final product turned out quite well, its not as good as a professional but it will do!

Welcome to AF-UK!

A few quick pictures. I will eventually make a mini guide on how I made this (no lid because hammerite is drying on it).

Do, its great stuff.

Built my own gun case yesterday, I will upload pics tonight after work.

Cheapass red dot sight off of ebay for a temp sight until I can afford an EOtech.

I have this http://www.actionhobbies.co.uk/Dan-Wesson-CO2-Revolver-Black-2-5-Inch_A10HKH.aspx?nh=171355#.U2SrXfldWqs Great gun. Nice feel and weight, however if you want to use it for CQB you will need downgrade shells. Also you can mod all of the dan wessons to be stupidly powerful, but then they are too powerful to use anywhere. Easy to strip and you can see everything and you don't have to worry about anything jumping out or springing out when you strip it.

Thanks for the chuckle. I assume it wouldn't be that bad in CQB w/350fps limit but outdoor maybe yeah.

This guy.

So I skirmished last night. I can confirm Cat Crap works a real treat and completely stops fog. Bearing in mind I wear a proto switch el as face protection and it gets real sweaty in there it only fogged where i didn't apply the cat crap, I only had to put it on once and it last me all night. I would seriously recommend it.

It's called I wear what I think looks cool loadout. (IWWITLC)

Give it a try, its amazing. https://www.youtube.com/watch?v=pG-AsWEPinw

I think that just ruins the look of airsoft RIFs as it's essentially like a flamethrower that spits bb's and is very expensive.

Where are you located?