occidio

Guide?

is it possible to make your own npas solution as it is on WE and GHK?

how will you fill them with gas

Have others experienced that they can not lift .43g bb´s? w. Maple Leaf rubber? I have tried with maple leaf autobot and MR rubber and with org nub with a cord inside to make it hard and with the maple leaf nub. in 2 MWS rifles It lifts nicely .36g with the hupup about halfway. I can see the hopup comes further down when i adjust it, but it's like that the bb dont get more back spin, does the BB sit so far forward in the chamber that it does not hit it properly? Does anyone have an idea?

JUSTICE_RAINS Barrel??

I have not done any major testing, I have just adjusted the hopup and aiming before the game. I shot after something like 35x35cm signs at 45m and 75m, they are on our shooting range. 45m hit almost constantly and 75m I think hit the 3 out of about 10 but all shots were very close, had it been a person I might have hit with them all, there was a little wind so a little hard to do a proper test. During games I felt it shot just as well as my VSR 10 which is fully modified and and I have played with it as a sniper for 10 years. But it's just a feeling, I think it worked as exactly as you would expect at long distances, I at least got a lot of kills at long distances. .

Have put new barrel in my mws. It surprises me a little how hard it got to shoot. Barrel 370mm 6.00mm + ML bucking nothing else. However, it was about 25 * C So that probably helped a little 😊 But stil..

prometheus 6.00 barrel, does anyone have experience with 6.00 in a GBBR? I want to raise FPS though I must also be able to hit from a distance

Can people with DMR maintain a proper 1.6-2 joule when it is cold 0 - 5 * C

okey. for the hop up "nub" ? Will the ML barrels fit?

Nice.. what was the joule on the middle setting? and at what temperature?

I have a bit of a hard time with these inner barrels, is there a difference in GBBR barrels? with AEG they all fit, minus length, but here I see that someone says fits WE, KWA, TM MWS etc plus sometimes says certain others?

Will this fit the MWS https://www.anareus.cz/gb/363-410mm/4273-maple-leaf-602-precision-inner-barrel-for-gbb-370mm--MPLF021.html

And the gun looks good same fps and same gas efficiency? And are the thing with the bolt fixed?

Should it be understood as that ML barrel does not fit in and is .5mm off?

Dont the "G&P have 3 power settings? 1.14j is that on the low or hi setting?

I play places where I have to use about 2j and others where I have to be under 1.69j. Another Precision Inner Barrel 6,03 has been ordered, but I would like the opportunity to adjust exactly as I can on my WE. as it is the easiest solution to not shoot too hot but still be close to max Joule Which type of (npas) is best, which one do you recommend,? NPAS KIT FOR TOKYO MARUI MWS GBB RA-TECH Angry Gun Enhanced Drop In Complete MPA Nozzle Set for Marui MWS M4 G&P MARUI MWS CNC ADJUSTABLE POWER NOZZLE If it is G&P which one (number) is right one for the desired joule? Thanks..

Are the new magazines marked 2 far worse than the first ones? I read that you can not green gas mode them, is that right? For I have seen test (badabing) shoot 150bb after greengas mode and I can not shoot much more than 50bb on a refill. So can the new ones not be modded in the same way?

Ok, thanks. Can it hold up to IT or? And how about gas efficiency

100fps just w. a Bartel? If I want to adjust the pressure what would you recommend to buy

Standard barrel. For the m4 mws

My hop is Upgraded 😉 so now i ned more power, the limet where i play is 2 joule for semi and its a big open Fields, so the Range is importent 🙂

I want longer range, my GHK goes just below 2joules (450fps) and has significantly longer range than my TM with about 1.4joules (390fps) on a hot day and 1.1joules (340) on a normal day 20C Desired joule 2 (fps 450) with the option to turn down. I use 0.43g bb or 0.36g What parts should I buy? Does it give extra wear, or is it just a "gas pressure" ? Will gas efficiency be much worse?