• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

What have you made?

Raid modded my Helikon BDU shirt.

Wrist adjuster and chest pocket buttons replaced with velcro.

Lower pockets removed and large loop velcro patches added. These were then attached to the upper arms.

Also bar tacked over a small rip. Quite a productive afternoon given how bleedin’ hot it was!

Coyote brown velcro from ContactLeft (Ebay) and Gutterman thread (colour 208 - from Amazon)

View attachment 94725

 
decided to make my own gun case. It's not the neatest but it works. 

Bought a tool box from b&q, hardboard, pick and pluck foam and a few cans of plasti dip. 

I made it three layers with the bottom one glued to the base of the box. With the pistol layer I can pick the foam out for other attachments if needed and just plasti dip that section again to firm it up. 

All the layers also have foam under each piece of equipment. 

View attachment 94927

View attachment 94928

View attachment 94929

View attachment 94930

 
Enid_Puceflange said:
Yeah! ?

Might have to make a mk2 and adjust the height of the crossbar to make it slightly less religious, but more importantly actually lift my pc a couple of inches higher ?
Click to expand...


Surely it's easier to just sling some additonal blocks under the 'feet' of it? ?

 
alxndrhll said:
Surely it's easier to just sling some additonal blocks under the 'feet' of it? ?
Click to expand...
That won’t really do the job

As the lowest part of the PC and the dangler pouch on the front are currently resting on them

 
Last edited by a moderator:
Got some Shadow Foam from Airsoft Anonymous.

For the top layer of the extra large case I bought some velcro straps from Amazon, cut slots for them then glued the whole thing into the lid with a strong foam adhesive. I have a foam layer that sits in the middle when the case is shut.

Decided to try something fancy for the other lid. The triskelion came out a bit wonky, but overall I'm very happy.

View attachment 96283

 
mightyjebus said:
Battery extender for KWA sliding stocks.
Click to expand...




If I could make a suggestion - extend it all the way back into the butt-pad cavity so it butts up against the flat section at the back. It'll act as a stabiliser to help to reduce flex/wobble. Also gives you more battery/wiring space.

 
Speedbird_666 said:
If I could make a suggestion - extend it all the way back into the butt-pad cavity so it butts up against the flat section at the back. It'll act as a stabiliser to help to reduce flex/wobble. Also gives you more battery/wiring space.
Click to expand...
not a bad idea.

 
A build in progress. Transplanting an AUG hop unit into my S&T M249. I've had feeding issues and low power in it right from day one so decided to try this before I retire and replace it.

View attachment 96704

More work to do yet, but as of today I've got it feeding and the power level is up. I fitted an adjustable nozzle which I'll need to dial in fully yet. Planning to give it a shake down at the next game day to see how it performs.

View attachment 96705

 
Last edited by a moderator:
You must log in or register to reply here.

Similar threads

A
Calling all that have a 3D printer, MOSQUITO Open Beta test!
Replies
12
Views
5K
Speedbird_666
Speedbird_666
sp00n
What have you just 3d printed (for airsoft)
22 23 24
Replies
471
Views
86K
MrTea
MrTea
Hef Legend
Snipermechanics SRS Guide
Replies
0
Views
7K
Hef Legend
Hef Legend
jeremythegenius
Mil-Tec Ghillie suit review
Replies
5
Views
5K
Happy
Happy
Back
Top