What have you made?

[RostokMcSpoons]

View attachment 94418

The Breakaway Coaster doohickies arrived from eBay.   With a bit of dremelling I gouged a chunk out of the inside to accommodate the existing zoom lever hump... and I have to say this is an excellent "Extended zoom lever mod" for a mere £6.

Video explaining the fitting and the dremel work... https://www.youtube.com/watch?v=4X4t6mK_Yz4

 

[Lozart]

View attachment 94418

The Breakaway Coaster doohickies arrived from eBay.   With a bit of dremelling I gouged a chunk out of the inside to accommodate the existing zoom lever hump... and I have to say this is an excellent "Extended zoom lever mod" for a mere £6.

Video explaining the fitting and the dremel work... https://www.youtube.com/watch?v=4X4t6mK_Yz4

Click to shrink...

I've had a couple of those on my scopes for a while! Dead handy and cheap!

 

[concretesnail]

A new liner for one of the cases.

View attachment 94634

 

[SSPKali]

Raid modded my Helikon BDU shirt.

Wrist adjuster and chest pocket buttons replaced with velcro.

Lower pockets removed and large loop velcro patches added. These were then attached to the upper arms.

Also bar tacked over a small rip. Quite a productive afternoon given how bleedin’ hot it was!

Coyote brown velcro from ContactLeft (Ebay) and Gutterman thread (colour 208 - from Amazon)

View attachment 94725

 

[Speedbird_666]

Mk5 Thunderflash holder to go on the front of my chest rig. Velcro backed - it'll have a loop of shock cord to provide tension.

View attachment 94817

View attachment 94816

 

[Stevobeavo]

decided to make my own gun case. It's not the neatest but it works. 

Bought a tool box from b&q, hardboard, pick and pluck foam and a few cans of plasti dip. 

I made it three layers with the bottom one glued to the base of the box. With the pistol layer I can pick the foam out for other attachments if needed and just plasti dip that section again to firm it up. 

All the layers also have foam under each piece of equipment. 

View attachment 94927

View attachment 94928

View attachment 94929

View attachment 94930

 

[Alvin]

Added some fans to my helmet. Beep boop.

Will see how it goes.

View attachment 95591

View attachment 95592

 

[Rogerborg]

Added some fans to my helmet

Click to shrink...

Ooh, noise!  I mean, nice!

 

[Enid_Puceflange]

Knocked up a PC stand

Buulders are in, plenty of useable off cuts and a router helps

Really helps when changing pouches around etc

View attachment 95620View attachment 95621

 

[Tactical Pith Helmet]

Knocked up a PC stand

Buulders are in, plenty of useable off cuts and a router helps

Really helps when changing pouches around etc

View attachment 95620View attachment 95621

Click to shrink...

You could crucify dwarves on that.  

 

[Enid_Puceflange]

You could crucify dwarves on that.  

Click to shrink...

Yeah! ?

Might have to make a mk2 and adjust the height of the crossbar to make it slightly less religious, but more importantly actually lift my pc a couple of inches higher ?

 

[alxndrhll]

Yeah! ?

Might have to make a mk2 and adjust the height of the crossbar to make it slightly less religious, but more importantly actually lift my pc a couple of inches higher ?

Click to shrink...

Surely it's easier to just sling some additonal blocks under the 'feet' of it? ?

 

[Enid_Puceflange]

Surely it's easier to just sling some additonal blocks under the 'feet' of it? ?

Click to shrink...

That won’t really do the job

As the lowest part of the PC and the dangler pouch on the front are currently resting on them

 

[Clanktank]

Some gear and shim holders for when the gearbox is in bits. Made from old bearings, brass hook stubs, and some wood offcuts. Can't have them lying around and getting mixed up. ?

View attachment 95635

 

[Skullchewer]

Got some Shadow Foam from Airsoft Anonymous.

For the top layer of the extra large case I bought some velcro straps from Amazon, cut slots for them then glued the whole thing into the lid with a strong foam adhesive. I have a foam layer that sits in the middle when the case is shut.

Decided to try something fancy for the other lid. The triskelion came out a bit wonky, but overall I'm very happy.

View attachment 96283

 

[concretesnail]

Love the cut cases

 

[mightyjebus]

Battery extender for KWA sliding stocks.

View attachment 96663

View attachment 96664

View attachment 96665

 

[Speedbird_666]

Battery extender for KWA sliding stocks.

Click to shrink...

If I could make a suggestion - extend it all the way back into the butt-pad cavity so it butts up against the flat section at the back. It'll act as a stabiliser to help to reduce flex/wobble. Also gives you more battery/wiring space.

 

[mightyjebus]

If I could make a suggestion - extend it all the way back into the butt-pad cavity so it butts up against the flat section at the back. It'll act as a stabiliser to help to reduce flex/wobble. Also gives you more battery/wiring space.

Click to shrink...

not a bad idea.

 

[Nick G]

A build in progress. Transplanting an AUG hop unit into my S&T M249. I've had feeding issues and low power in it right from day one so decided to try this before I retire and replace it.

View attachment 96704

More work to do yet, but as of today I've got it feeding and the power level is up. I fitted an adjustable nozzle which I'll need to dial in fully yet. Planning to give it a shake down at the next game day to see how it performs.

View attachment 96705