-
Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.
The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here
If you have any issues please post about them in the Forum Feedback thread: Go Here
THE TM MWS thread
- Thread starter Wo1f
- Start date
most likely they have different gas release valves. Maybe modify them to push more gas.
Hi , PMAG install high flow valve . I think that problem is the sealing lip with nozzle.... leaking gas
Hypokondrikern
Members
- Oct 15, 2019
- 163
- 36
It could be worthwhile to read up on Bada Bing Pictures's facebook page. He had more or less the same problems - a lack of recoil and power.
https://www.facebook.com/BadaBingPictures/
I have seen very few complaints about the magazines and find myself confident in a purchase. The loss in recoil seems like an acceptable trade off for the pmag style and comfy weight but one should probably do a slight filing to the top of the bolt tab to prevent jamming. But I'd like to hear more opinions.
What do you guys think of these?
40 round mags :0
P.S is it time to compile a google doc FAQ and summary of earlier pages on the MWS topic? Something for the beginners but also to formulate a consensus. We had one but it got lost somewhere on page 80. Can we make it pinned somewhere?
This is weird, hi flow valve gives you more gas not less so recoil and FPS should increase unless there’s a leak somewhere. Swap the valve and test. Is it still the same, worse or better?
Last edited by a moderator:
Davegolf
Members
- Sep 22, 2009
- 2,103
- 850
Check between the original and new mag for differences.
The centre pin looks different in length.
Is the gas route rubber the same flowing internally?
And is it sealing to the nozzle properly - thinly put some silicone grease on the top surface of the gas route, insert and remove the mag - is there witness grease on the nozzle entry?
Is it being held high enough by the mag catch?
The centre pin looks different in length.
Is the gas route rubber the same flowing internally?
And is it sealing to the nozzle properly - thinly put some silicone grease on the top surface of the gas route, insert and remove the mag - is there witness grease on the nozzle entry?
Is it being held high enough by the mag catch?
hi guys , I am doing a lot of test and I see that sealing gas route to nozzle it´s worst .
But If I up mag , up all struct and maybe have jam issues. therefore I think that is better up gas route.
@Davegolf both. gas route and high mag catch.
But If I up mag , up all struct and maybe have jam issues. therefore I think that is better up gas route.
Hypokondrikern
Members
- Oct 15, 2019
- 163
- 36
So mag sits too high and gas route / rubber lip is too high as well?
I remember that badabing changed nothing but the empty magazine tab which means that the protruding lip might be what causes the jam. Did you replace it with standard magazine lip?
Last edited by a moderator:
I can only tell you that everything seems like a gas route sealing problem with the nozzle.
I talked already with badabing and he swap all valves and tab bolt lock with parts TM. I have used very little mag and I can´t say if mag has jam issues.
Hypokondrikern
Members
- Oct 15, 2019
- 163
- 36
I see, but I think he replaced the gas route lip with a standard TM as well. I recall seeing an image of it at least. Did you try this yourself? Could be that it is too tight or deformed.
The problem is the gas route.
If you have nozzle Stock , you need use gas route TM with shim lower gas route to higher and perfect fit.
If you have nozzle Angry gun , in my case MPA ... you can use both gas route , but you need shimm gas route too.
service ace 1 arms is very poor , one week waiting ask.....
lazer_actual
Members
- Apr 24, 2020
- 3
- 0
Would there be any interest in a modified AW WE box mag to fit the MWS? I’ve spoken to someone who has done it and isn’t interested in doing any more. I plan on making a couple of them for myself, wondering if it’s something anyone else would be interested in? It’d hold around 330 rounds. What would be people be prepared to pay? I should have mine built in the next few weeks all being well with post.
G
Guest
Guest
lazer_actual
Members
- Apr 24, 2020
- 3
- 0
Have an engineer friend who wants to have a crack at them! I wondered if you’d pop up! Haha! Looking at tig welding them!
Similar threads
