Not impressed

[Jack Reacher]

Well I've had Rs type 56-2 for a few weeks now & gotta say overall I'm not impressed by it I suspect I've got a wrongun ,range is poor ,power is low ,accuracy is only good at short distances & to top it off today on its 2nd skirmish it won't fire properly on semi ? Any ideas anyone .cheers Jack

 

[BrightCandle]

What do you mean by its not firing properly on semi? Could be a variety of potential problems (jamming the gearbox temporarily or failing to discharge the round etc etc).

Have you had the FPS of the gun tested? Might be an idea to do so and just make sure something isn't obviously wrong in the pneumatics of the gun and that its compressing air sufficiently.

 

[M_P]

Could just be a lemon.

 

[NickM]

If its brand new there is a very simple solution, you contact the retailer that sold it to you and it should get sent back.

If its second hand things are a bit more of a problem. You could send it off to someone like Kingdom of Airsoft ( a very well respected gun tech up in Scotland) or have a bash yourself.

 

[Jack Reacher]

It was chronoed a couple of weeks ago & it was was 285/290 fps .It fires a couple of shots on semi then make a crunching sound .To be honest I was expecting a lot better performance overall but it's not much better than the hire guns .Its not a mag problem because it did it on all 6 mags I've got .Is it still covered under warranty as I've only had 6/7 weeks & it was only its second skirmish today .cheers jack

 

[Jack Reacher]

I just checked I bought it on 16feb .cheers jack

 

[n1ckh]

Send it back under warranty, ring them tomorrow, explain what's going on with it

Unfortunately its not like a car when you know whats wrong before sticking it in for repair to see if they actually do it

 

[Jack Reacher]

Back it goes then ,might Aswell get some upgrades done whilst it's there any suggestions .cheers jack

 

[Monty]

No, don't touch the internals. Just send it back

 

[BrightCandle]

A metallic crunching noise could be the gears crashing against the anti reversal latch, although I can't say I have ever heard it myself so its not a normal noise. Could also just be the gears are not shimmed well and its making a lot of noise when the gears are stopped immediately on anti reversal, that could very well make quite a bit of noise. Or it could be something like the tappet or nozzle scrapping on something. Its an open it up and look for the damage/wear type of description that one I am afraid. Which since its in warranty I would just send it back and let the retailer send you a nice new working one, especially since the FPS is sounding on the low side as well.

 

[Jack Reacher]

Someone else said bad shimming & gunk on connecters & I wanted a new spring anyway to get it nearer to 340/50,cheers jack

 

[n1ckh]

As stated above, its usually bad gear meshing plus lack of greasing, if they sort it out they can upgrade a few bits for you at the same time

 

[Jack Reacher]

A Minnor set back just blooming annoying ,I even had to send the mag back as soon as I got it because it wouldn't feed & there supposed to be bomb proof ,guess I just got a Friday after noon one lol cheers jack

 

[n1ckh]

Well fingers crossed mate it dont happen again

Shame it turned out to be such a dog & your next one will be much better

 

[NickM]

Send it back, its under warrenty so they should just send you a new one. In that case you should get one with a better fps. I wouldn't mention upgrades yet.

Most guns work good enough out of the box that upgrading too early will end up causing you pain in the long run.

I have 2 ICS guns, 1 L85 that I bought first and after 6 months I started tinkering, I upgraded all sorts and my tinkering has had some good but also some bad effects. I now rarely skirmish this one because it's not as good as the stock M4 I bought as a backup. I will continue to mess about with the L85 and if I decide to upgrade the M4 down the road I'll send it to a reputable gun tech rather than do it myself I'll also not do it till the L85 is working sweetly.

 

[EvilMonkee]

I had exactly the same issue with my 56-1 - turned out it was a stripped piston. Fire Support whipped it out and added a new spring - hey presto 60m shooting gun....

 

[Jack Reacher]

I doubt there send me a new one I expect there just fix this one but I dontbmind Aslong as it works as it should .cheers jack

 

[Jack Reacher]

Well it's getting picked up on third-Friday & I'm gonna have the spring upgraded is it honestly worth having any further upgrades done whilst it's there ie hop rubber ,bucking ,air nozzle because they the parts don't cost that much & whilst it's apart it would be easier as I don't wanna mess about in the future.Honest opinions Wellcome .cheers jack

 

[n1ckh]

I upgraded the piston in my CM16 cause the plastic teeth got stripped so I swapped out the piston head, cylinder head and nozzle but then had to downgrade to an M90 spring

If you ask them to upgrade those parts, they can put in the relevant spring then

 

[Ian_Gere]

Who did you buy it from? Please let us know how it is when it comes back to you.