Liamcella96

Amazing thanks everyone. I've taken it apart today and the internals seem shot. Plastic piston a little stripped. Nozzle not the best. I will replace the internals and let you know how it goes. Thanks

You just place some o rings over the barrel until the maximum pressure is applied that still let's you put the receivers back together? Not heard of this before I will give it a go.

Hi mate. Thanks for reply. I have a zci hop & Macaron rubber with an omega nub. Would you just recommend to go up a spring strength. I forgot to mention I'm currently at 290fps. I'm just looking to boost to the 340ish mark. Uk based yes and on 0.2gs

Hello, I have managed to get my hands on a great VFC m4 which is a smiling size to an mp5 so I plan to use it more as an smg but also if I want to field it in woodland games that would be great. The barrel I have to use is a 147mm 6.03 bore. Can anybody help in what will help me achieve 350fps? Any tips etc. What cylinder do you recommend? Should I go for a full cylinder or a 1/2. Etc Thanks

All out of stock

Sorry.... I don't think you understand. Probably my fault for posting that link I've ordered that gearbox from another company with no bushings etc.. It's just that link was easier to share to show you the box I have ordered.

Hello. I've had some troubles with my airsoft gearbox and I have managed to find a replacement for a good price that will see me through for now This is the shell... https://www.bullseyecountrysport.co.uk/nuprol-airsoft-v2-gearbox-shell-casing-delta-series-20234-p.asp Trouble is... where ever I look I'm unable to find the bushing/bearing size for this shell. Does anybodybhappen to have some knowledge or experience with this shell who can give me the answer so I can order my bushings before the shell arrives. Thanks a lot.

Hi guys. I purchased this battery for my AEG standard crane stock as I thought i would be able to make it fit but sadly I'm unable to. Does anybody have some tips for me to get it to fit into my crane stock. Any help would be amazing. Thanks FCONEGY Airsoft LiPo Battery 3S 11.1V 2400mAh 20C Rechargeable Triple Stick Battery Pack with Mini Tamiya Plug for Air Soft Gun Rifle https://www.amazon.co.uk/dp/B07PJJJMVB/ref=cm_sw_r_awdo_navT_g_G97G7BAYHW8DWJXJWJHP

Yeah it's a complete air seal. But does it matter that the valve is in there still

Hi guys. I have an mk23 pistol and as you'd expect my TM mags started leaking... what a surprise. Im 99% sure it was due to old dried out O rings but whilst I was having to open it anyway I thought I may as well do the full monty. So I have filled the release valve with resin as is recommended. 1 thing I didn't do though as I had read it was OK was I didnt remove the valve from the hole before filling it on top of the valve. Does this make any difference? Or am I going to have to drill it all out and refill it? I'm pretty sure it shouldn't matter as it is still completely filled but can somebody confirm please. Thanks

Yeah I was able to do a full cycle. Even with the spring In there as well. The anti reversal latch is also definitely in place because as I was turning the gear I was locking the gears after every so often and then when I pulled the latch up it reset the system as you would expect.

Hi guys. I have received a V2 gearbox from a friend who left his RIF out of action for a while and when he returned the gun no longer fired. I took the gearbox apart to take a look and the grease has solidified partially which I thought could be the issue. I have completely stripped the gearbox, and cleaned all gears etc so no grease or grease build up at all, also cleaned piston etc and replace grease in necessary places. When the gearbox is open, all of the gears move freely and are placed correctly. All wiring has also been tested and working as it ahould to power motor from the firing switch. When I tried to fire the gearbox. I can hear the motor turning what must be about 1mm before it hits the 1st gear but then everything is just rock solid and the motor cannot turn the gears. The battery and connectors then get rather hot due to the motor being frozen. I have tried the motor and tested it in another RIF and it is working perfectly. Does anybody have any idea why the gearbox has frozen? I have also been able to turn the gears manually with a screwdriver and the piston and spring seems to be working correctly. I just don't know why the motor cannot make the gears turn.

Thanks guys. Figured it out now. In order to twist the outer barrel I had to remove the 2 locking pins. How do you get them back in easily haha.

Hi Guys. I'm trying to take apart my airsoft gun so I am able to give it a full clean and remove any dirt and dust that may have built up over years of playing. The gun is a A&K SPR Mod 1. My question is how in God's name do I remove the hand guard? I can't for the life of me work out how. As it seems the iron sights need to come off first also and I cannot figure how to get them off either. any help whatsoever is greatly appreciated and happy sorting everybody.