Neilbarker

Yup I was indeed

Both a we sig and a we m4. I was trying to compare the difference between standard we green gas and the 3.0 so o just filled two mags, one of each, the normal gas fired fine so I'm Assuming I filled both correctly :/ and yeah it's the same at room temp too

I bought some nuprol 3.0 gas for the colder weather and while trying it out I was getting about 20 feet before the bbs dropped that's if it cycled at all. So why? It's for cold weather it's 10 degrees tonight according to the car, so why the poor performance? Thanks

They're not in the feed lips I can see inside the feed lips and there's bbs stuck beside each other under them but no bbs actually in them

Yeah pushing it right down and it came back up and the bbs fed right for two more shots then it jammed again

Okay pushed it down, it reset, fired two bbs and done it Again though there's not one rattling about an more it's just stuck. I wanna open it and take the bbs out and try different ones but in not sure if that'd stop me being able to send it back as it just got here yesterday

Nope it's seated properly and yeah the gun cycles just doesn't Fire bbs. The bbs are jammed under the feed lips. I can see there's two bbs jammed further down and then there's one that rattles around on top and even if I pull the follower down they still stay jammed in there but the bbs below it come down with the follower

Nope open blaster .25s

I have a problem with my we m4 gas mag. It's a double stack mag and as I'm firing it, the top two bbs seem to jam and the gun just cycles gas. I'm just wondering if anyone knows what's causing it and how to fix it? Thank you

Ive seen aluminium nozzles and steel bolts and stuff, but my guess is that if I upgrade one part itll increase wear on the others, so it'd need to be done all at once. hop and barrel wqise, they take VSR rubbers? would putting a tight bore and a new hop rubber do me well? I cleaned the barrel when i got it and damn it was dirty

Hey guys, ordered a a WE M4, and I'm just wondering what I should replace in what order? I've read that the steel bolt can be a pain to install at times, and that it causes increased wear on almost everything, so if i was to replace it, what else would need done at the same time? Thank you.

Just a quick question, which 7 inch RIS will fit onto the delta ring without needing it all changing? I've been looking but can't make sense of the differences in the rails available.

Turns out they are the open bolt versions, so they just reused the pictures

Yeah the email time is fine, I was just wondering if anyone had any idea which version they were selling. I'll give them a call and see what's what. Thanks

Yesterday afternoon I emailed them, still nothing back as of yet

I'm looking at this m4 on zero one (not sure if I can link here remove if not please) http://www.zerooneairsoft.com/product_info.php?cPath=268_317_484&products_id=4923 Now the description says open bolt but I think I'm right in saying that the pictures show the brass tube, which is the closed bolt. I've emailed them but so far no reply, I'm just wondering if anyone knows which version it really is? Thank you.

From what I've read the hammer spring makes it use more gas? Some people were getting only 12-13 shots from the full mag. Does the slide lock still work with the 150% recoil spring in there?

Hey, I'm after some info on the best parts to upgrade in the pistol I have. I have already replaced the spring guide as I read that the little pin on it was a particular weak point. So I got a guarder one and so far no problems. It also has a guarder 6.02 barrel and I think it's an A plus bucking. But what else should I replace, and with what? Ive searched around but would like to know what's worked from other people's experience. Thank you

Here's to another expensive hobby. Excellent fun today in Fife and the guys are fantastic. Hicaps make soo much noise though

Well thanks for the heads up regarding makes! Doubtless I'll be back clogging up the forum With some useless questions in the future! Thanks again

Like I said, I might get there and find that the noise isn't so bad at all, however from what I've heard watching reviews and videos and stuff the whine is almost unmissable. And I get what you mean that if something goes wrong that's me out until it's fixed which is something I didn't consider at all to be honest. Mag capacity isn't a huge issue, I'd feel kinda cheaty blasting away with a 400 round mag on an m4. But it might all change when I get there and try it out!

I could likely go to around 400 initially. I feel like I will enjoy airsoft however I doubt I'll enjoy using an AEG as the noise is seriously off putting to me, however until I play on sunday I wont know for sure. But as is stands I feel like a GBBR will be what I want and im just trying to get a feel for brands and whats good and bad and what not just now.

The motor noise mainly. I just dont like the little whine they make

okay thank you, how about this? it says king arms and GHK which the other thread points out as good.

Hello all, I'm after some advice on guns for a first timer. I've been interested in this for a while but never got roudn to it really, always torn between this or paintball but decided to bite the bullet and go to a game this sunday to see before I go spending any cash, getting the UKARA started too, though I dont mind two tone if I can have my own gun, I can sort that out at a later date. I have looked and looked and just cannot seem to find an AEG I like. Im not a fan of the motor noise at all. I have a WE P226 and had it apart many times while just messing around with it and reckon I could figure out the internals of a rifle well enough to keep it performing relatively well and if not, I'm willing to learn the hard way! I've found two guns I like at a decent price but I cant really find too much about one of them online and would like a bit of advice This one here or this one here however I am open to sugggestions and what not as you guys on here are far more knowledgable than I am. Thank you.