THE TM MWS thread

[Wo1f]

It’s certainly right up there @EvilMonkee  my first game is next Sunday and after that, both rifles will be stripped and new bucking/nub combos tried and I’ll do another comparison. I really do like the modify tan and SixG though. Just a shame the modify wears quite quickly. 

 

[Softcore]

Anyone know where I could get a original 10.3 inch cqbr barrel? Impulse101 had some in the past but they're out of stock now.

 

[occidio]

Are the new magazines marked 2 far worse than the first ones?
I read that you can not green gas mode them, is that right?
For I have seen test (badabing) shoot 150bb after greengas mode and I can not shoot much more than 50bb on a refill. So can the new ones not be modded in the same way?

https://www.reddit.com/r/GasBlowBack/comments/hbsotk/tm_m4_mws_magazine

 

[Davegolf]

General consensus was the new #2 mags are better than the #1.

If you read back in this thread and other outside findings.

Are you sure you are filling them correctly??

 

[RMDavis]

Tried fitting the Magpul extended mag release yesterday to no avail...

The threads on the TM catch are obviously different, and wouldn't go on.

I'm pretty sure I have seen photos of guys with these fitted however. Is it a case of using a genuine mag release catch?

 

[Wild Weasel]

2 hours ago, occidio said:

Are the new magazines marked 2 far worse than the first ones?
I read that you can not green gas mode them, is that right?
For I have seen test (badabing) shoot 150bb after greengas mode and I can not shoot much more than 50bb on a refill. So can the new ones not be modded in the same way?

https://www.reddit.com/r/GasBlowBack/comments/hbsotk/tm_m4_mws_magazine

I've green gas modified mine before I new that v2's existed, mine are great but my Full auto is very unreliable I think due to this.  This is not an issue for me as I don't use it and the mags fill reliably and easily get through two to three loads of bb's, consistency seem fine with only a small deviation over one load of bb's

 

[SSPKali]

Tried fitting the Magpul extended mag release yesterday to no avail...

The threads on the TM catch are obviously different, and wouldn't go on.

I'm pretty sure I have seen photos of guys with these fitted however. Is it a case of using a genuine mag release catch?

I have an airsoft spec one that I don't use (left handed so kept dropping mags when slinging the weapon!) let me see if I can dig it out

 

[GregArm]

Hi guys,

My first post is here. I'm from Germany, sorry if I write something wrong.
 

I found this topic searching for MWS on the net, and I am very happy to see a lot of information about it.

Half a year ago I bought my Tokyo Marui MWS and I read everything that I can’t, because this is my first M4 GBB.

So far I have done all the mods that you guys recommended here, for example, a mod with green gas and the 4 most important upgrades:

- Prometheus 370mm 6.03

- SixG Super Nub

- Npas Ra-tech

- Modify Tan bucking

It seems to me that this works well together.

I noticed that many guys are building weapons of DMR, but for now I would like to play in the classic version.

Since automatic shooting mode is prohibited in Germany, we only shoot semi-automatic.

I want to order spare parts for my MWS such as Bolt Carrier, Nozzle and Buffer.  There are many options and combinations, but I am confused and do not know what works best together.  Advise details to increase rate of fire.  To make the cycle run faster and softer.

Thanks in advance.

HSB Spaser , Angry Gun Super Recoil Buffer , Dynamic Precision Aluminum Lightweight Bolt Carrier , ENHANCED DROP IN COMPLETE MPA NOZZLE 

View attachment 59673

It looks like my weapon now

View attachment 59677

 

[Davegolf]

Hello and welcome!

So you are happy with your gun as it is?

You are happy with your guns power?

You are not allowed full auto.

So your goal is to increase cycle speed, and reduce recoil?

I can only comment on personal experience - a UAC Aluminium bolt with HSB Spacer will make for a very fast cycle.

You may need to unscrew your buffer tube 1 or 2 turns to make the bolt catch reliable.

 

[Wo1f]

Also, there’s no point in putting a light bolt carrier in and then a stupidly heavy buffer as they will cancel each other out. I found the angry gun super recoil buffer (silver one) much too heavy. It gave a good kick, but it was a sluggish kick. 

 

[GregArm]

Thanks to Davegolf and Wo1l for quickly responding to my question.

Yes, I am happy with my weapon and how strong and accurate it is. We are not allowed a full auto. You correctly understood that I want to increase the speed of the cycle. 

So what you recommended: Does this mean I only need to buy a UAC Aluminum Bolt and an HSB Spacer.

Nozzle I leave the original one from TM MWS (or I need to buy one too), but also Npas Ra-tech too?

Install SixG HSB as in the photo from Dave SixG.  And it works without a spring and a buffer?

Sorry for the stupid questions and bad English.

View attachment 59682

View attachment 59685

 

[marine]

hi guys , someone replace piston head ? I´m looking for the best.

PD : My Nozzle MPA has broken .... Bad quality and Bad piston head.

 

[Wo1f]

@GregArm you still need the spring and buffer. You put the spacer in first, then the spring, then the buffer. The spacer pre-compresses the spring for better response 

 

[Hypokondrikern]

@GregArm I’d buy the HSB first and if you find yourself with the extra cash - buy yourself an extra bolt of Aluminium with all the guts. This gives you an emergency bolt for long games in case of the standard breaking. But this not really needed and will cost you around 120 €. Rather then spend the money on sporting your gear. Last advice: The HSB is enough  

 

[GregArm]

@GregArm вам все еще нужны пружина и буфер. Сначала вы вставляете проставку, затем пружину, затем буфер. Распорка предварительно сжимает пружину для лучшего отклика 

Thanks Wo1f. Today I will write a message to Dave SixG.

@GregArm I’d buy the HSB first and if you find yourself with the extra cash - buy yourself an extra bolt of Aluminium with all the guts. This gives you an emergency bolt for long games in case of the standard breaking. But this not really needed and will cost you around 120 €. Rather then spend the money on sporting your gear. Last advice: The HSB is enough  

Thanks for the help.  Do you also mean UAC Aluminum Bolt or is it talking about another bolt?

 

[Hypokondrikern]

Thanks Wo1f. Today I will write a message to Dave SixG.

Thanks for the help.  Do you also mean UAC Aluminum Bolt or is it talking about another bolt?

Yeah, there are many different.  But I went with the SAI and UAC both working great. 

 

[GregArm]

Yeah, there are many different.  But I went with the SAI and UAC both working great. 

Thank you. I ordered HSB from Dave today.  Now I'm looking for a UAC bolt.

 

[Cipher-032]

Be aware, if you run a HSB, you get a FPS increase.

I didnt notice much cycling rate difference if im honest?

Gunna remove and see what It feels like this weekend

 

[GregArm]

Be aware, if you run a HSB, you get a FPS increase.

I didnt notice much cycling rate difference if im honest?

Gunna remove and see what It feels like this weekend

I think that I will get HSB soon and compare if there is a difference.

It is a pity that I can not find the UAC bolt anywhere.?

 

[Hypokondrikern]

I think that I will get HSB soon and compare if there is a difference.

It is a pity that I can not find the UAC bolt anywhere.?

http://www.bunnyworkshop.com.hk/airsoft/UAC_Aluminum_Lightweight_Bolt_Carrier_for_Marui_M4A1_MWS_GBB_Sliver