• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

THE TM MWS thread

Hi there! I'm having some trouble with my TM MWS! Unfortunately it seems to almost be short stroking on semi auto, leading to random uncontrollable bursts of full auto. I recently installed an NPAS and the problem got worse (it was there before). Could it also be some problem with my sears? Before it was mostly a problem when the gas was low, now it happens on a full mag. Thank you! 

 
Rawrcakkes said:
Hi there! I'm having some trouble with my TM MWS! Unfortunately it seems to almost be short stroking on semi auto, leading to random uncontrollable bursts of full auto. I recently installed an NPAS and the problem got worse (it was there before). Could it also be some problem with my sears? Before it was mostly a problem when the gas was low, now it happens on a full mag. Thank you! 
Click to expand...
Hi, i did hear from random burst in semi from an AMG tuning experiment video. He meant this problem is coming from the bolt where it hits the hammer. If its sqashed to much it doesnt recycle the hammer fully. He recomended a lighter hammer spring in combination with his magazin valve and flute valve for the nozzle. And check if the nozzle valve spring is not stuck. Had full auto trouble because of this, as well in semi when it got stuck

 
Last edited by a moderator:
I still have my stock bolt, perhaps I can try to install that later tomorrow and see if that fixes the problem. Maybe my guns modify bolt has finally had enough rounds in it to get some decent wear? 

 
Hi , 

I have leak gas to one magazine. O-ring is the MGG2-79 part. 

Somebody know measure to this o-ring ?

 
Afternoon guys . So after a spell out from playing I dusted off the tm and got round to fitting the angry gun  bolt with npas . Set up the desired fps with .20s . ( this was with a original tm mag ) . Now here's the issue , I have afew of the iron Pmags so I fill up the mag same gas same bbs and the fps was all over the place from 60fps right up to 380fps but mostly around the 240 mark. Any ideas ? The last time I played I used the mags without issue but I had the uac ( I think it was )lightened bolt instead anyone else had any issues with the angry gun bolt ? 

I know the Pmags are hit and miss but I just thought I got lucky as I never had a issue with them all last year 

 
Dread68 said:
...anyone else had any issues with the angry gun bolt ? 
Click to expand...


I'm mostly an idiot... but it sounds to me that your problem of wildly varying FPS more likely stems from the NPAS (and/or its seal with the P-Mags) than the angry gun bolt.

 
Hello guys ! I am from Spain ( Madrid) , now as cold as it is i've decide to put down my mws just for winter . Meanwhile i can do some improvments , in fact i wanna raise his potencial to maximum , i am not so eager to spend lots of cash but since i have much love for gbb more than anything else  i can make an exception. I am following this page from last year ago but i still haven't a clear idea what to do to my rifle . I wanna make a dmr gbb so the main idea should be a mk12a1 like external . I wan't some advices about what to buy , i have a local airsoft store that is like a rwa retailer .... Juddging from yours experience what to do : barrel lenght , type , hopup chamber , rubber , bolt , buffer , mags , gas !? 

 
Last edited by a moderator:
Uncle Pauly said:
I'm mostly an idiot... but it sounds to me that your problem of wildly varying FPS more likely stems from the NPAS (and/or its seal with the P-Mags) than the angry gun bolt.
Click to expand...
I'm home now so going to swap over the bolts . I was just confused that they worked perfectly with the old bolt and not the new one . But I'm sure someone on here had said they had issues also with the angry gun bolt 

 
Troubleshoot by using only the original TM mags.  The iron airsoft mags are known to be junk.  I own the AG BCG and MPA nozzle and it works flawlessly.

 
Rawrcakkes said:
I still have my stock bolt, perhaps I can try to install that later tomorrow and see if that fixes the problem. Maybe my guns modify bolt has finally had enough rounds in it to get some decent wear? 
Click to expand...
I would try it. If its working this AMG guy was right. Maybe i will look up to get his stuff. Please tell the results

 
Last edited by a moderator:
Reapur said:
Troubleshoot by using only the original TM mags.  The iron airsoft mags are known to be junk.  I own the AG BCG and MPA nozzle and it works flawlessly.
Click to expand...
Yep swapped to the uac bolt and iron mags and they work spot on together . Swapped back to the angry gun bolt and were all over the place again . So the iron mags are off in the back of my cupboard and will stick with the tm mags 

 
so I notice angry gun uploaded some new bolt designs the other day... and I'm sat here wondering if the branded 416 bolt means they have more things in the works potentially?

anyone have any thoughts or info on this?

View attachment 53080

 
Last edited by a moderator:
You must log in or register to reply here.

Similar threads

Rechard
Which M4 gas mag is better? VFC or MWS?
Replies
6
Views
1K
ProfHappyCat
ProfHappyCat
Angelvill3
Guns modify mws magazine issue
Replies
2
Views
715
Angelvill3
Angelvill3
Cr0-Magnon
MWS GBBR for Plinking?
Replies
5
Views
634
BigStew
B
aragoth
Custom m733 MWS
Replies
3
Views
361
ButcherBill
ButcherBill
Impulse
G&G m700 knock arm and plunger set issues
Replies
6
Views
1K
Impulse
Impulse
Back
Top